Hangzhou Hikvision Digital Technology KDE, KDM User Manual
Video Intercom Card Reader Module
Quick Start Guide
Scan to get detailed User Manual
Video Intercom Card Reader Module·Quick Start Guide
ii
Quick Start Guide
©2018 Hangzhou Hikvision Digital Technology Co., Ltd.
This quick start guide is intended for users of card reader module: DS-KD-M (13.56 MHz)
and DS-KD-E (125 KHz).
Nametag module is the component of the module door station. Use it along with the
main unit.
It includes instructions on how to use the Product. The software embodied in the
Product is governed by the user license agreement covering that Product.
About this Manual
This Manual is subject to domestic and international copyright protection. Hangzhou
Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This
manual cannot be reproduced, changed, translated, or distributed, partially or wholly,
by any means, without the prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are
registered trademarks or the subject of applications for the same by Hikvision and/or its
affiliates. Other trademarks mentioned in this manual are the properties of their
respective owners. No right of license is given to use such trademarks without express
permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL.
HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE
USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION
CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE
WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA
OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN
DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
Video Intercom Card Reader Module·Quick Start Guide
iii
Support
Should you have any questions, please do not hesitate to contact your local dealer.
Video Intercom Card Reader Module·Quick Start Guide
iv
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the EMC Directive
2014/30/EU, LVD Directive 2014/35/EU, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info
Video Intercom Card Reader Module·Quick Start Guide
v
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see:
www.recyclethis.info
Video Intercom Card Reader Module·Quick Start Guide
vi
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
The working temperature of the device is from -40º C to 60º C.
All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
Please use the power adapter, which is provided by normal company. The power
consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug
the power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the device yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
The power supply must conform to LPS. The recommended adaptor models and
manufacturers are shown as below. Use the attached adaptor, and do not change the
adaptor randomly.
Model
Manufacturer
Standard
ADS-24S-12 1224GPCN
Shenzhen Honor Electronic
Co., Ltd.
GB
KPL-060F-VI
Channel Well Technology
Co., Ltd.
GB
Warnings Follow
these safeguards to
prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.
Video Intercom Card Reader Module·Quick Start Guide
vii
Cautions
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or
places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the specification of the device for
the detailed operating temperature), cold, dusty or damp locations, and do not
expose it to high electromagnetic radiation.
Do not aim the device at the sun or extra bright places. A blooming or smear may
occur otherwise (which is not a malfunction however), and affecting the endurance of
sensor at the same time.
Please use a soft and dry cloth when clean inside and outside surfaces of the device
cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure
occurred, you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device and
lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion.
Replace with the same or equivalent type only. Dispose of used batteries according to
the instructions provided by the battery manufacturer.
The warranty does not apply to the product defects and failures arisen as a result of
improper mounting (in contradiction herewith).
When the proper mounting instructions are not met, water might get in and destroy
the electronics.
Video Intercom Card Reader Module·Quick Start Guide
viii
Table of Contents
1 Overview ...................................................................................................... 1
2 Terminal and Wiring ..................................................................................... 2
3 Installation ................................................................................................... 3
3.1 Configure Sub Module Address ............................................................................... 3
3.2 One-Module Installation .......................................................................................... 4
3.2.1 One-Module Surface Mounting ........................................................................ 4
3.2.2 One-Module Flush Mounting ............................................................................ 8
3.3 Two-Module Installation ........................................................................................ 12
3.3.1 Two-Module Surface Mounting ...................................................................... 12
3.3.2 Two-Module Flush Mounting .......................................................................... 17
3.4 Three-Module Installation ..................................................................................... 22
3.4.1 Three-Module Surface Mounting .................................................................... 22
3.4.2 Three-Module Flush Mounting ....................................................................... 27
3.5 More-than-Three Module Installation ................................................................... 33
3.5.1 More-than-Three Module Surface Mounting .................................................. 33
3.5.2 More-than-Three Module Flush Mounting ..................................................... 39
4 Remote Operation ...................................................................................... 48
4.1 Activate Main Unit ................................................................................................. 48
4.2 Edit Network Parameters ....................................................................................... 49
4.3 Add Device ............................................................................................................. 50
Video Intercom Card Reader Module·Quick Start Guide
1
1 Overview
Card reader module supports issue cards and unlock door via swiping card. It works
together with the main unit and other sub modules.
Its appearance is shown as below.
Figure 1-1 Card Reader Module Appearance
Table 1-1 Appearance Description
No.
Description
1
Card Reading Area
2
Module-connecting Interface(output)
3
Module-connecting Interface(input)
4
Debug Port
The module connecting interface is used to connect with main unit or other function
module, such as nametag module, keypad module, card reader module, etc. All these
modules (except main unit) are known as sub module.
Video Intercom Card Reader Module·Quick Start Guide
2
2 Terminal and Wiring
The card reader module’s interfaces and terminals as below:
Figure 2-1 Terminals and Interfaces
Table 2-1 Descriptions of Terminals and Interfaces
No.
Interface
Description
A1
485-
Module-connecting Interface (Input)
A2
485+
A3
12V IN
A4
GND
A5
485-
Module-connecting Interface (Output)
A6
485+
A7
12V OUT
A8
GND
Video Intercom Card Reader Module·Quick Start Guide
3
3 Installation
Before you start:
Make sure the device in the package is in good condition and all the assembly parts
are included.
Sub module must work along with the main unit.
Set the sub module address before start the installation steps.
Make sure the place for surface mounting is flat.
Make sure all the related equipment is power-off during the installation.
Tools that you need to prepare for installation:
Drill (ø6), cross screwdriver (PH1*150 mm), and gradienter.
Buy corresponding accessory package for installation. The accessory package model
and its suitable installation method as below:
Package
Model
Mounting Method
Note
DS-KD-ACW1
One-Module Surface Mounting
Install the device according
to the instructions.
Not all the lines in the
accessory package will be
used.
DS-KD-ACW2
Two-Module Surface Mounting
DS-KD-ACW3
Three-Module Surface Mounting
DS-KD-ACF1
One-Module Flush Mounting
DS-KD-ACF2
Two-Module Flush Mounting
DS-KD-ACF3
Three-Module Flush Mounting
3.1 Configure Sub Module Address
You need to set the sub module address via DIP before installation.
Steps:
1. Remove the rubber cover on the sub module rear panel to expose the DIP switch.
Video Intercom Card Reader Module·Quick Start Guide
4
Figure 3-1 DIP Switch
2. Set the sub module address according to the DIP rules, and install the rubber cover
back.
Digit 1, 2, 3, 4 are used to coding the sub module address; Digit 5, 6, 7, 8 are reserved.
Valid sub module address range is 1 to 8. The No. should be unique for sub modules
that connected to the same main unit.
The sub module address and corresponding switch status as below.
Sub Module
Address
1 2 3 4 .5 6 7
8
Digit 1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Digit 2
OFF
ON
ON
OFF
OFF
ON
ON
OFF
Digit 3
OFF
OFF
OFF
ON
ON
ON
ON
OFF
Digit 4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
3.2 One-Module Installation
3.2.1 One-Module Surface Mounting
Mounting Frame
Video Intercom Card Reader Module·Quick Start Guide
5
Figure 3-2 Front and Side View
The dimension of one module mounting frame is: 117(L)×107(W)×32.7(D) mm.
The dimensions above are for reference only. The actual size can be slightly different
from the theoretical dimension.
Steps:
1. Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed leveled
via measuring with the gradienter.
2. Chisel 4 holes with drill align to the screw holes on the sticker.
The suggested size of hole is 6 (diameter) × 25 (depth) mm.
The suggested length of cables left outside is 100 mm.
Video Intercom Card Reader Module·Quick Start Guide
6
Figure 3-3 Chisel Screw Hole
3. Remove the sticker and insert the expansion sleeves into the screw holes.
4. Fix the mounting frame onto the wall with 4 expansion bolts.
Video Intercom Card Reader Module·Quick Start Guide
7
Figure 3-4 Fix the Mounting Frame
The mounting frame should be placed exactly as below for this step. The tamper plate
should be at the low-right.
5. Connect the cables to the corresponding interfaces of the main unit and insert it into
the frame.
Video Intercom Card Reader Module·Quick Start Guide
8
Figure 3-5 Insert the Main unit
6. Use the hexagon wrench in the package fix the cover onto the frame.
Figure 3-6 Fix the Cover
3.2.2 One-Module Flush Mounting
Gang Box
Video Intercom Card Reader Module·Quick Start Guide
9
Figure 3-7 Front and Side View
Figure 3-8 Appearance Description
Video Intercom Card Reader Module·Quick Start Guide
10
The dimension of one-module gang box is: 115(L)×134(W)×56(D) mm.
The dimensions above are for reference only. The actual size can be slightly different
from the theoretical dimension.
Steps:
1. Cave the installation hole, and pull the cable out.
The suggested dimension of installation hole is 118(L)×108(W)×45.5(D) mm.
The suggested length of cables left outside is 100 mm.
Figure 3-9 Cave the Installation Hole
2. Remove the plastic sheet in the cable entry.
3. Insert the gang box into the hole and pull out the cables through the cable entry.
Mark the screw holes’ position with a marker, and take out the gang box.
Figure 3-10 Mark the Screw Holes
4. Chisel 4 holes with drill align to marks on the wall, and insert the expansion sleeves
into the screw holes.
The suggested size of hole is 6 (diameter) × 45 (depth) mm.
5. Fix the gang box with 4 expansion bolts.
Loading...