How it Works
Hangzhou Hikvision Digital Technology
Loading...
K3B601LE
Users manual
120 pgs4.04 Mb0

Hangzhou Hikvision Digital Technology K3B601LE, K3B601LM Users manual

Swing Barrier
User Manual
Product Name
Model
Description
Swing Barrier
DS-K3B601-L Series
Left Pedestal
DS-K3B601-M Series
Middle Pedestal
DS-K3B601-R Series
Right Pedestal
DS-K3B601A-L Series
Left Pedestal
DS-K3B601A-M Series
Middle Pedestal
DS-K3B601A-R Series
Right Pedestal
User Manual
© 2018 Hangzhou Hikvision Digital Technology Co., Ltd. This manual applies to swing barrier.
Note: L represents left pedestal, M represents middle pedestal, and R represents right pedestal.
It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product.
About this Manual
This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision
Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be
reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Support
Should you have any questions, please do not hesitate to contact your local dealer.
i
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. —Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the
radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed
of as unsorted municipal waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information see:
www.recyclethis.info
ii
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage.
iii
Warnings Follow these safeguards to prevent serious injury or death.
Cautions Follow these precautions to prevent potential injury or material damage.
Warnings
All the electronic operation should be strictly compliance with the electrical safety regulations,
fire prevention regulations and other related regulations in your local region.
Please use the power adapter, which is provided by normal company. The power consumption
cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause over-heat
or fire hazard.
Please make sure that the power has been disconnected before you wire, install or dismantle
the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power
cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)
Cautions
Stainless steel may be corroded in some circumstances. You need to clean and care the device
by using the stainless steel cleaner. It is suggested to clean the device every month.
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the specification of the device for the detailed
operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.
The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or
radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may occur
otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
Please use the provided glove when open up the device cover, avoid direct contact with the
device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.
iv
Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do
not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure occurred, you
need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion. Replace with the
same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.
v
Table of Contents
Chapter 1 Overview ..................................................................................................................... 1
1.1 Introduction..................................................................................................................... 1
1.2 Main Features .................................................................................................................. 1
Chapter 2 Installation .................................................................................................................. 2
2.1 Disassembling Pedestals .................................................................................................. 2
2.2 Installing Pedestals........................................................................................................... 2
Chapter 3 Wiring ......................................................................................................................... 4
3.1 Components Introduction ................................................................................................ 4
3.2 Wiring Electric Supply ...................................................................................................... 4
3.3 Wiring Interconnecting Cable .......................................................................................... 5
3.4 Terminal Description ........................................................................................................ 7
3.4.1 Master Control Board Terminal Description.................................................................. 7
3.4.2 Slave Control Board Terminal Description..................................................................... 7
3.4.3 Main Control Board Terminal Description..................................................................... 8
3.4.4 Main Control Board Serial Port ID Description ............................................................ 11
3.4.5 RS-485 Wiring ............................................................................................................ 12
3.4.6 RS-232 Wiring ............................................................................................................ 13
3.4.7 Wiegand Wiring ......................................................................................................... 14
3.4.8 Barrier Control Wiring................................................................................................ 14
3.4.9 Alarm Output Wiring ................................................................................................. 16
3.5 Wiring Lithium Battery (Optional) .................................................................................. 16
Chapter 4 Device Settings .......................................................................................................... 18
4.1 Setting Closed Position .................................................................................................. 18
4.2 Pairing Remote Control (Optional) ................................................................................. 19
4.3 Initializing Device ........................................................................................................... 19
4.4 Switching RS-485/RS-232 Mode ..................................................................................... 19
4.5 Switching Relay Output Mode (NO/NC) ......................................................................... 20
4.5.1 Barrier Control Relay Output Mode ............................................................................ 20
4.5.2 Alarm Relay Output Mode (NO/NC) ........................................................................... 20
Chapter 5 Device Activation ...................................................................................................... 22
5.1 Activating via SADP Software ......................................................................................... 22
5.2 Activating via Client Software ........................................................................................ 23
Chapter 6 Client Operation ........................................................................................................ 26
6.1 Function Module ........................................................................................................... 26
vi
6.2 User Registration and Login ........................................................................................... 26
6.3 System Configuration ..................................................................................................... 27
6.4 Access Control Management ......................................................................................... 28
6.4.1 Adding Access Control Device .................................................................................... 29
6.4.2 Viewing Device Status ................................................................................................ 42
6.4.3 Editing Basic Information ........................................................................................... 43
6.4.4 RS-485 Settings .......................................................................................................... 43
6.4.5 Authenticating M1 Card Encryption ........................................................................... 44
6.4.6 Remote Configuration ................................................................................................ 45
6.5 Organization Management ............................................................................................ 55
6.5.1 Adding Organization ................................................................................................... 56
6.5.2 Modifying and Deleting Organization ......................................................................... 56
6.6 Person Management...................................................................................................... 56
6.6.1 Adding Person ............................................................................................................ 56
6.6.2 Managing Person ....................................................................................................... 67
6.6.3 Issuing Card in Batch .................................................................................................. 68
6.7 Permission Configuration ............................................................................................... 69
6.7.1 Adding Permission ..................................................................................................... 70
6.7.2 Applying Permission ................................................................................................... 71
6.8 Advanced Functions ....................................................................................................... 72
6.8.1 Access Control Parameters ......................................................................................... 72
6.8.2 Card Reader Authentication ....................................................................................... 75
6.8.3 Multiple Authentication ............................................................................................. 76
6.8.4 Open Door with First Card.......................................................................................... 79
6.8.5 Anti-Passing Back ....................................................................................................... 80
6.9 Searching Access Control Event ...................................................................................... 81
6.9.1 Searching Local Access Control Event ......................................................................... 82
6.9.2 Searching Remote Access Control Event ..................................................................... 82
6.10 Access Control Event Configuration ................................................................................ 83
6.10.1 Access Control Event Linkage ................................................................................. 83
6.10.2 Access Control Alarm Input Linkage ........................................................................ 84
6.10.3 Event Card Linkage ................................................................................................. 85
6.10.4 Cross-Device Linkage .............................................................................................. 88
6.11 Door Status Management .............................................................................................. 89
6.11.1 Access Control Group Management ....................................................................... 89
6.11.2 Anti-control the Access Control Point (Door) .......................................................... 91
vii
6.11.3 Status Duration Configuration ................................................................................ 92
6.11.4 Real-time Card Swiping Record............................................................................... 94
6.11.5 Real-time Access Control Alarm.............................................................................. 94
6.12 Arming Control .............................................................................................................. 95
6.13 Time and Attendance .................................................................................................... 96
6.13.1 Shift Schedule Management .................................................................................. 97
6.13.2 Attendance Handling............................................................................................ 103
Appendix A Tips for Scanning Fingerprint .............................................................................. 106
Appendix B DIP Switch Description ........................................................................................ 107
DIP Switch Introduction ........................................................................................................... 107
DIP Switch Corresponded Functions ........................................................................................ 107
Appendix C Table of Audio Index Related Content ................................................................. 109
Appendix D Error Code Description ........................................................................................ 110
viii
The swing barrier with two barriers and 12 IR lights is designed to detect unauthorized entrance or exit. By adopting the swing barrier integratedly with the access control system, person should authenticate to pass through the lane via swiping IC or ID card, scanning QR code, etc. It is widely used in attractions, stadiums, construction sites, residences, etc.
Chapter 1 Overview
1.1 Introduction
1.2 Main Features
32-bit high-speed processor TCP/IP network communication
The communication data is specially encrypted to relieve the concern of privacy leak
Permissions validation and anti-tailgating Remaining open/closed mode selectable Bidirectional (Entering/Exiting) lane
The barrier opening and closing speed can be configured according to the visitors flow
The barrier will be locked or stop working when people are nipped. Anti-forced-accessing
The barrier will be locked automatically without open-barrier signal. It can bear the force of up to 120 Nm.
Self-detection, Self-diagnostics, and automatic alarm Audible and visual alarm will be triggered when detecting intrusion, tailgating, reverse passing,
and climbing over barrier.
Remote control and management Online/offline operation LED indicates the entrance/exit and passing status. Barrier is in free status when powered down; If the device is installed with lithium battery
(optional), the barrier remains open when powered down
Fire alarm passing
When the fire alarm is triggered, the barrier will be open automatically for emergency evacuation.
Valid passing duration settings
System will cancel the passing permission if a person does not pass through the lane within the valid passing duration
Opens/Closes barrier according to the schedule template. Up to 3000 visitor cards and up to 60,000 cards except for visitor cards can be added
1
Chapter 2 Installation
2.1 Disassembling Pedestals
Purpose:
Before installation, you should use the key to open the pedestals. View the pictures below to find the locks and installation holes.
2.2 Installing Pedestals
Before you start:
Prepare for the installation tools, check the device and the accessories, and clear the installation base.
Notes:
The device should be installed on the concrete surface or other non-flammable surfaces. If the installation area is too close to the wall, make sure the distance between the pedestal
and the wall should be no more than 120 mm, or you cannot open the pedestal’s top panel.
Steps:
1. Draw a central line on the installation surface for installing the center pedestal.
2. Draw another two parallel lines on each side of the central line for installing the other two
pedestals.
Note: The distance between the nearest two line is L+200 mm. L represents the lane width.
3. Drill holes on the ground according to the installation holes on the pedestals and insert the
expansion sleeves.
4. Bury interconnecting cables for pedestal communication.
2
Note: For detailed information about burying and wiring interconnecting cables, see 3.3 W iring
Interconnecting Cable.
5. According to the entrance and exit marks on the pedestals, move the pedestals to the
corresponded positions.
Note: Make sure the installation holes on the pedestals and the base are aligned with each
other.
6. Secure the pedestals with expansion bolts.
Note: Do not immerse the pedestal in the water. In special circumstances, the immersed height
should be no more than 10 mm.
The installation footprint is as follows:
3
Chapter 3 Wiring
3.1 Components Introduction
Purpose:
By default, basic components of the swing barrier are connected well. You should wire the pedestals together for communication and wire the swing barrier to the AC electric supply.
Note: The voltage fluctuation of the electric supply is between 100 VAC and 220 VAC, 50 to 60 Hz.
The picture displayed below describes each component’s position on the swing barrier.
3.2 Wiring Electric Supply
Wire electric supply with the switch in the pedestal. Terminal L and terminal N are on the switch, while terminal PE should connect to a ground wire (yellow and green wire).
4
3.3 Wiring Interconnecting Cable
Purpose:
You should use interconnecting cables to connect the master lane board and the slave lane board for components communication. The picture displayed below describes the interconnecting cable hole’s position on the pedestals.
5
The picture displayed below describes the interconnecting cable’s wiring diagram.
Notes:
The supplied interconnecting cable length is 3.75 m. If you need a longer one, ask our
technique supports or sales and purchase 5.5 m interconnecting cables.
The inner diameters of the low voltage conduit and the high voltage conduit should be larger
than 30 mm. If there is a high-power peripheral (for authentication) installed on the left pedestal (according to the picture displayed above), you should increase the inner diameter of the high voltage conduit.
General burying method: Bury one network cable and one AC power cord for the right pedestal
and bury one network cable and one AC power cord for the central pedestal before installation. If no AC power cord buried independently, you should bury an AC power cord between the right pedestal and the central pedestal.
If you want to bury both of the AC power cord and the low voltage cable at the entrance side,
the two cables should be in separated conduits to avoid interference.
If all wires of the interconnecting cable have connected with peripherals and more peripherals
are required to connect, you should increase the conduit diameter or bury another conduit for the external cable.
6
3.4 Terminal Description
Purpose:
The lane controller contains master lane controller and slave lane controller, which controls the IR beams, motor, and other components work.
3.4.1 Master Control Board Terminal Description
Purpose:
The master lane control board contains lane communication interfaces, interconnecting interface, motor encoder interface, remaining open and fire alarm interface, barrier opening directions interface, people counting interface, remote control receiving antenna, motor drive interface, brake interface, power interface, battery interface, DIP switch, and seven-segment display (SSD).
Note: For detailed information about the DIP switch, see Appendix BDIP Switch Description.
The picture displayed below is the master control board diagram.
3.4.2 Slave Control Board Terminal Description
Purpose:
The slave lane control board contains lane communication interfaces, interconnecting interface, motor encoder interface, remaining open and fire alarm interface, barrier opening directions interface, people counting interface, motor drive interface, brake interface, power interface, battery interface, and seven-segment display. The picture displayed below is the slave control board diagram.
7
3.4.3 Main Control Board Terminal Description
8
Main Controlling Board Terminal Description
Power
Output1
+12V
Grounding
GND
Power Output
Wiegand
Card
Reader1
OK
Indicator of Card Reader Control Output (Invalid
Card Output)
ERR
Indicator of Card Reader Control Output (Valid
Card Output)
BZ
Card Reader Buzzer Control Output
W1
Wiegand Head Read Data Input Data1
W0
Wiegand Head Read Data Input Data0
GND
Grounding
Wiegand
Card Reader
2
OK
Indicator of Card Reader Control Output (Invalid
Card Output)
ERR
Indicator of Card Reader Control Output (Valid
Card Output)
BZ
Card Reader Buzzer Control Output
W1
Wiegand Head Read Data Input Data1
W0
Wiegand Head Read Data Input Data0
GND
Grounding
RS-485
Interface
GND
Grounding
RS-485 B-
Connect to Card Reader RS485-
RS-485 B+
Connect to Card Reader RS485+
GND
Grounding
RS-485 C-
Connect to Card Reader RS485-
RS-485 C+
Connect to Card Reader RS485+
Power
Output2
5V
5 VDC Power Output
GND
5 VDC Grounding
RS-232
Interface
GND
Grounding
RS-232 G-
Connect to Card Reader RS232-
RS-232 G+
Connect to Card Reader RS232+
GND
Grounding
RS-232 H-
Connect to Card Reader RS232-
RS-232 H+
Connect to Card Reader RS232+
Power Input
+12V
12 VDC Power Input
GND
12 VDC Grounding
Event Input
C1
Event Alarm Input 4
GND
Grounding
C2
Event Alarm Input 3
C3
Event Alarm Input 2
Table 3-1 Main Control Board Terminal Description
9
Main Controlling Board Terminal Description
GND
Grounding
C4
Event Alarm Input 1
Exit Button
B2
Door 2 Signal Input
GND
Grounding
B1
Door 1 Signal Input
Door Lock
(Relay)
D1-
Door 1 Relay Output(Dry Contact)
D1+
D2-
Door 2 Relay Output(Dry Contact)
D2+
Alarm
Output
NO/NC1
Alarm Output Relay 1(Dry Contact)
COM1
NO/NC2
Alarm Output Relay 2(Dry Contact)
COM2
NO/NC3
Alarm Output Relay 3(Dry Contact)
COM3
NO/NC4
Alarm Output Relay 4(Dry Contact)
COM4
Network Interface
LAN
Network Accessing
Notes:
The alarm input hardware interface is normally open by default. So only the normally open
signal is allowed. It can be linked to the buzzer of the card reader and access controller, and the alarm relay output and open door relay output.
The DIP of RS485 card ID is set as 1 and 4 by default. 1 is for entering, and 4 is for exiting. Set the
DIP as 3 for connecting visitor card reader.
The Wiegand card reader 1 and 2 respectively refer to the entering and exiting card reader. The alarm output supports network camera accessing. For any requirements, the door lock can control the door barrier status of the third party. D1
controls the barrier opening for entrance, while D2 controls the door opening for exit. For details, see 4.5.1 Barrier Control Relay Output Mode.
C3 and C4 in the event input can also be people counting interface. C3 controls people counting
for entrance, while C4 controls people counting for exit. When the main control board detects signals in C3 and C4, the people number will be accumulated. For detailed information about people counting and people number, see Configuring People Counting Parameters in 6.4.6 Remote Configuration.
10
UART2/UART3 Jumper Cap:
Reserved serial port. Use the jumper cap to switch the serial port communication mode. You can switch between the RS-485 communication mode and the RS-232 communication mode. By default, it is in RS-485 communication mode.
UART6 Jumper Cap:
Use the jumper cap to switch the serial port communication mode with the slave lane controller. You can switch between the RS-232 communication mode and the RS-485 communication mode. By default, it is in RS-232 communication mode.
UART5 Jumper Cap:
Use the jumper cap to switch the serial port communication mode with the slave lane controller. You can switch between the RS-484 communication mode and the RS-232 communication mode. By default, it is in RS-485 communication mode.
3.4.4 Main Control Board Serial Port ID Description
Purpose:
You can use the jumper cap on the main control board to switch the interface communication mode. For details about switching between RS-232 and RS-485 communication type, see 4.4 Switching RS-485/RS-232 Mode.
According to the picture above, the RS-485 serial port corresponds to UART2 and UART3. RS-232 serial port is corresponded to UART7 and UART8. Wiring Interface is corresponded to UART1, UART4, UART6, UART6, and Lane. The main control board descriptions are as follows:
11
UART1 Jumper Cap:
Use the jumper cap to switch the serial port communication mode with the master lane controller. You can switch between the RS-484 communication mode and the RS-232 communication mode. By default, it is in RS-485 communication mode.
Lane:
Use the jumper cap to switch the serial port communication mode with the lane controller. By default, the interface is wired and it is in RS-485 communication mode.
If wiring other controllers (compatible with Hikvision communication protocol), use the jumper cap to switch between RS-485 and RS-232 communication mode.
UART4:
The serial port is in the wiring interface according to the picture above, which has a fixed RS-232 communication mode to communicate with the master lane controller. It contains no jumper cap and cannot change the communication mode.
UART7/UART8:
Reserved serial port. The serial port has a fixed RS-232 communication mode. It contains no jumper cap and cannot change the communication mode. It can connect QR code scanner, card recycler, and text screen.
3.4.5 RS-485 Wiring
Notes:
There are five RS-485 interfaces, which are for connecting ID card reader, IC card reader, QR
code scanner, fingerprint and card reader, card recycler, text screen, fingerprint reader, and face recognition terminal. Take the wiring of RS-485 card reader as an example.
For details about text screen, see Configuring Screen Parameters in 6.4.6 Remote Configuration.
12
3.4.6 RS-232 Wiring
Note: There are three RS-232 interfaces (UART4, UART7, and UART8). UART7 and UART8 can
connect QR code scanner, card recycler, and text screen, while UART4 can connect QR code scanner, card recycler, text screen, and face recognition terminal. For details about text screen, see Configuring Screen Parameters in 6.4.6 Remote Configuration. Take the wiring of face recognition terminal as an example.
13
3.4.7 Wiegand Wiring
Note: You must connect the OK/ERR/BZ if using access controller to control the LED and buzzer of
the Wiegand card reader.
3.4.8 Barrier Control Wiring
Purpose:
By default, the barrier has connected with the main control board. The lane control board can control the barrier status. If possible, the device can connect with a third party lane control board to control the third party barriers. Interface D1 controls barrier opening for entrance, while interface D2 controls barrier opening for exit.
14
Entering Wiring
Exiting Wiring
15
3.4.9 Alarm Output Wiring
Note: For details about changing the relay output status via the jumper cap, see 4.5.2 Alarm Relay
Output Mode (NO/NC).
3.5 Wiring Lithium Battery (Optional)
Purpose:
The lithium battery supplies power for master lane control board and slave lane control board when the device is powered off. The battery interface position is as follows:
Before you start:
Ask our technique support and sales and purchase for the lithium battery.
Steps:
1. Install lithium batteries.
1) Remove the screws on the battery component to disassamle the battery component.
2) Put the lithium battery inside the component.
3) Secure the components on the device by the screws.
2. Insert the battery connecter to the battery interface on the lane control board.
Note: There are battery interfaces on both of the master lane control board and slave lane
control board.
16
17
Chapter 4 Device Settings
After installation and wiring completed, you should set the barriers closed position (study mode) before entering the working mode. You can also set the passing mode and memory mode, pair the remote control, initialize the hardware, switching between RS-485 communication mode and RS-232 communication mode, and view relay output NO/NC diagram by setting the DIP switch.
Study Mode: The barrier will learn the closed position. Normal Mode: The device will work properly. The barrier position configured in study mode is
the closed position when the device is working normally.
Passing Mode: There are 9 passing modes, including controlled bi-direction, controlled
entrance and prohibited exit, controlled entrance and free exit, free bi-direction, free entrance and controlled exit, free entrance and prohibited exit, prohibited bi-direction, prohibited entrance and free exit.
Memory Mode: By default, the memory mode is enabled. When multiple cards are swiped and
authenticated, it allows multiple persons passing through the lane. When it counts the passing people number is equal to the card swiped times, or no person passing through the lane after the last person passing, the barriers will be closed.
Note: You can also set the DIP switch to control the action of swiping card to open the barrier in
alarm area, entrance and exit controlling type, remote control pairing, etc. For details about the DIP switch value, see Appendix B DIP Switch Description.
4.1 Setting Closed Position
Purpose:
Enter the study mode through DIP switching to set the closed position of the device barrier.
Steps:
1. Set The No.1 and No.2 switches of the 8-digit DIP Switch on the master lane controlling board
by referring the following figure to enter the study mode.
2. Adjust the closed position of the barrier.
3. Power on the device.
The device will remember the current position (closed position) automatically.
4. Power off the device.
5. Set the No.1 and No.2 switches of the 8-digit DIP Switch on the master lane controlling board
by referring to the following figure.
6. Power on the device again.
18
The barrier will open automatically and turns back to the closed position. At this circumstance, the device enters the normal mode. Note: For details about the DIP switch value and meaning, see Appendix B DIP Switch Description.
4.2 Pairing Remote Control (Optional)
Purpose:
Pair the remote control to the device through DIP switch to open/close the barrier remotely.
Note: for details about the remote control’s operations, see the related user manual.
Before you start:
Ask our technique supports or sales and buy the remote control.
Steps:
1. Power off the swing barrier.
2. Set the No.1 switch of the 4-digit DIP Switch on the master lane control board according to the
figure below.
3. Power on the swing barrier and it will enter the pairing mode.
4. Hold the Close button for more than 10 seconds.
The indicator of the remote control will flash twice if the pairing is completed.
Notes:
You can also pair the remote control via the client software. For details, see Managing
Remote Control in 6.4.6 Remote Configuration.
Only one swing barrier can pair the remote control. If multiple swing barriers are in the
pairing mode, the remote control will select only one of them to pair.
For details about DIP switch value and meaning, see Appendix B DIP Switch Description.
4.3 Initializing Device
Steps:
1. Remove the JP11 jumper cap.
2. Disconnect the power and reboot the device. The device buzzer buzzes a long beep.
3. When the beep stopped, plug the jumper cap back.
4. Disconnect the power and reboot the device.
Note: The initializing of the device will restore all the parameters to the default setting and all
the device events are deleted.
4.4 Switching RS-485/RS-232 Mode
Take the UART2 and UART3 on the main control board as an example. If the Jumper cap’s position is like the picture displayed below. (The black part is the jumper cap.) The serial port is in RS-485 communication mode.
19
If the Jumper cap’s position is like the picture displayed below. (The black part is the jumper cap.) The serial port is in RS-232 communication mode.
4.5 Switching Relay Output Mode (NO/NC)
4.5.1 Barrier Control Relay Output Mode
The pins of the barrier control relay on the main control board is as below:
The jumper cap’s position of barrier opening for entrance (NO) is as below:
The jumper cap’s position of barrier opening for exit (NO) is as below:
The jumper cap’s position of barrier closing for entrance (NC) is as below:
The jumper cap’s position of barrier closing for exit (NC) is as below:
4.5.2 Alarm Relay Output Mode (NO/NC)
Alarm Relay Output Mode (NO):
20
Alarm Relay Output Mode (NC):
21
Loading...
+ 90 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use