How it Works
Hangzhou Hikvision Digital Technology
Loading...
K1TMC
User Manual
58 pgs2.98 Mb0
Table of contents
Loading...

Hangzhou Hikvision Digital Technology K1TMC, K1E, K1MC User Manual

Access Control Terminal
Quick Start Guide
UD.6L0206D1079A01
Series
Model
Standalone Access Control Terminal
DS-K1T105E
DS-K1T105M-C（with Camera）
Optical IP-based Fingerprint
Access Control Terminal
DS-K1T200EF
（with Camera）
-C-C
DS-K1T200MF--C
Quick Start Guide
© 2015 Hangzhou Hikvision Digital Technology Co., Ltd.
This quick start guide is intended for users of the models below:
It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product.
About this Manual
This Manual is subject to domestic and international copyright protection. Hangzhou
Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This
manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
i
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
Support
Should you have any questions, please do not hesitate to contact your local dealer.
0100001050825
ii
Regulatory Information
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.
2011/65/EU.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS Directive
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings Follow
these safeguards to prevent serious injury or death.
Cautions Follow these precautions to prevent potential injury or material damage.
Warnings
All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local region.
Please use the power adapter, which is provided by normal company. The power
consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug
the power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the device yourself. (We shall not
iv
Access Control Terminal·Quick Start Guide
assume any responsibility for problems caused by unauthorized repair or maintenance.)
Cautions
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the specification of the device for
the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.
The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as
heater or radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may
occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
Please use the provided glove when open up the device cover, avoid direct contact
with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the device
cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure
occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion.
Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.
v
Access Control Terminal·Quick Start Guide
Table of Contents
1 Overview ...................................................................................................... 1
1.1 Introduction ............................................................................................................. 1
1.2 Main Features .......................................................................................................... 2
1.2.1 Main Features of DS-K1T105 Series Model ....................................................... 2
1.2.2 Main Features of DS-K1T200 Series Model ....................................................... 2
2 Appearance .................................................................................................. 4
2.1 Appearance of DS-KITI05 Series Model ................................................................... 4
2.2 Appearance of DS-KIT200Series Model ................................................................... 5
2.2.1 Description of Components .............................................................................. 5
2.3 Appearance of Keys ................................................................................................. 6
2.3.1 Description of Items .......................................................................................... 6
3 Terminal Connection .................................................................................... 8
3.1 Terminal Description ................................................................................................ 8
4 Wiring Description ..................................................................................... 12
4.1 External Device Wiring Overview .......................................................................... 12
4.2 The Wiring of External Card Reader ...................................................................... 13
4.2.1 The Wiring of External RS485 Card Reader ..................................................... 13
4.3 The Wiring of Electric Lock and Door Magnetic ..................................................... 14
4.3.1 The Wiring of Electric Lock .............................................................................. 14
4.3.2 The Wiring of Door Contact ............................................................................ 15
4.4 The Wiring of Exit Button ...................................................................................... 16
4.5 The wiring of Alarm Input ...................................................................................... 17
4.6 The Wiring of External Alarm Device ..................................................................... 17
4.7 Card Reader Connection ........................................................................................ 18
4.7.1 The Wiring of Wiegand Output ....................................................................... 18
4.7.2 The Wiring of RS485 Output ........................................................................... 19
5 Activating the Access Control Terminal ....................................................... 21
5.1 Activating via SADP Software ................................................................................. 21
5.2 Activating via Client Software ................................................................................ 23
6 Basic Operation .......................................................................................... 27
6.1 User Management ................................................................................................. 28
6.1.2 Adding User ..................................................................................................... 29
6.1.2 Managing User ................................................................................................ 31
6.2 Communication Settings ........................................................................................ 34
6.2.1 Network Settings ............................................................................................. 34
6.2.2 Serial Port Settings .......................................................................................... 35
6.2.3 Wiegand Settings ............................................................................................ 36
vi
Access Control Terminal·Quick Start Guide
6.2.4 Wi-Fi Settings .................................................................................................. 37
6.3 System Settings ...................................................................................................... 38
6.3.1 Setting System ................................................................................................. 39
6.3.2 Managing Data ................................................................................................ 40
6.3.3 Restoring Settings ........................................................................................... 41
6.3.4 Door Settings ................................................................................................... 41
6.3.5 Setting the Camera .......................................................................................... 42
6.4 Time Settings ......................................................................................................... 43
6.5 Upload/Download Settings .................................................................................... 44
6.6 Testing ................................................................................................................... 45
6.7 Log Query Settings ................................................................................................. 46
6.8 System Information ............................................................................................... 47
vii
Figure 1-1 DS-K1T105 Series Standalone Access Control Terminal Front Panel
DS-K1T105 is a series of standalone access control terminal with picture capturing function. DS-K1T105 is designed with a 2.8-inch LCD display screen, and HD camera (2 MP optional). It supports two network communication methods (TCP/IP, and Wi-Fi), and supports offline operation.
Figure 1-2 DS-K1T200 Series IP-Based Fingerprint Access Control Terminal Front
Panel
DS-K1T200 is a series optical IP-based fingerprint access control terminal with multiple advanced technologies including fingerprint recognition, face detection, Wi-Fi, smart card recognition, LCD display screen, and picture capturing technology. It is designed
Access Control Terminal·Quick Start Guide

1 Overview

1.1 Introduction

1
with a 2.8-inch LCD display screen, and HD camera (2 MP optional). It is equipped with optical fingerprint recognition module (supporting 1:1 mode and 1:N mode), and supports offline operation.
Access Control Terminal·Quick Start Guide

1.2 Main Features

1.2.1 Main Features of DS-K1T105 Series Model

Doorbell ringtone settings function. Touch mode and blue light display technique for keypad. Stand-alone settings for the terminal. 2.8-inch LCD display screen. Transmission modes of wired network (TCP/TP) and Wi-Fi. Face detection and picture capturing function implemented by built-in
camera (2 MP optional, only supports DS-K1T105E/M -C)
Supports multiple door opening modes (card, card + password, exit
button, etc.)
Supports RS485 communication for connecting to external card reader. Supports working as a card reader, and supports Wiegand interface and
RS485 interface for accessing the controller.
Max. 100,000 valid card No., and Max. 300,000 access control events
records storage.
Supports EM card reading (DS-K1T105E/E-C)
Supports Mifare card reading, including card No. reading, & writing
function (DS-K1T105M/M-C)
Tampering detection, unlocking overtime alarm, invalid card swiping over
times alarm, and duress card alarm.
Accurate data and time display provided by built-in electronic clock and
watchdog program to ensure the basic function of the terminal.
Data can be permanently saved after power-off.

1.2.2 Main Features of DS-K1T200 Series Model

Doorbell ringtone settings function.
2
Access Control Terminal·Quick Start Guide
Touch mode and blue light display technique for keypad. Stand-alone settings for the terminal. 2.8-inch LCD display screen. Transmission modes of wired network (TCP/TP) and Wi-Fi. Face detection and picture capturing function implemented by built-in
camera (2 MP optional, only supports DS-K1T200EF/MF-C)
Supports RS485 communication for connecting external card reader. Supports working as a card reader, and supports Wiegand interface and
RS485 interface for accessing the controller.
Max. 100,000 card No., Max. 300,000 access control events records , and
Max. 9500 fingerprints storage.
Adopts the optical fingerprint module, supporting 1:N mode (fingerprint,
card + fingerprint) and 1:1 mode (card + fingerprint).
Supports multiple authentication modes (card, fingerprint, card +
fingerprint, card + password, fingerprint + password, card + fingerprint + password, and so on.)
Supports EM card reading (DS-K1T200EF/EF-C) Supports Mifare card reading, including card No. reading, and sector
reading & writing (DS-K1T200MF/MF-C)
Tampering detection, unlocking overtime alarm, invalid card swiping over
times alarm, duress card alarm, and so on.
Accurate data and time display provided by built-in electronic clock and
watchdog program to ensure the basic function of the terminal.
Data can be permanently saved after power-off.
3
No.
Description
1
2.8-Inch LCD Display Screen
2
HD Camera with 2 MP (only DS-K1T105E/M/ -C
support)
3
Keypad
4
USB 2.0 Interface
5
Tampering Switch
6
PSAM Card Slot
7
External Wiring Terminals
8
Serial Port
9
Ethernet Port
Access Control Terminal·Quick Start Guide

2 Appearance

2.1 Appearance of DS-KITI05 Series Model

Please refer to the following content for detailed information of the DS-K1T105 series model.
Figure 2-1 Appearance of DS-K1T105 Series Model
Table 2-1 Description of DS-K1T105 Series Model
4
No.
Description
1
2.8-Inch LCD Display Screen
2
HD Camera with 2 MP (only DS-K1T200EF/MF
-C support)
3
Keypad
4
Optical Fingerprint Reading Module
5
USB 2.0 Interface
6
Tampering Switch
7
PSAM Card Slot
8
External Wiring Terminals
9
Serial Port
Access Control Terminal·Quick Start Guide

2.2 Appearance of DS-KIT200Series Model

Please refer to the following content for detailed information of DS-K1T200 series model
Figure 2-2 Appearance of DS-K1T200 IP-Based Fingerprint Access Control
Terminal

2.2.1 Description of Components

Table 2-2 DS-K1T200 IP-Based Fingerprint Access Control Terminal
Components
5
No.
Description
10
Ethernet Port
No.
Description
1
Numeric Keys: Enter number in the textbox. Direction Keys: Select icons in the menu.
2
Editing Key: Click the key to enter/exit the editing status.
3
Exiting Key: Click the key to exit the menu.
4
Confirming Key: Click the key to confirm operations.
Long-click the key to enter the login interface.
5
Deleting Key: Click the key to delete contents in the textbox.
6 Status Indicator: Indicator for power, ring, and connection status
POWER
Power Status
Solid Blue: Normal Power. Off：Power Exception.
Doorbell Ring LINK
Normal Card/
Normal Card: Solid Blue
Access Control Terminal·Quick Start Guide

2.3 Appearance of Keys

Figure 2-3 Appearance of Keys

2.3.1 Description of Items

Table 2-3 Description of Keys
6
No.
Description
Illegal Card
Illegal Card: Solid Red
Connection Status
Off: Network or Wi-Fi Disconnected.
Solid Blue: Network or Wi-Fi connected, but client unarmed.
Flicker Blue: Network or Wi-Fi connected, but client armed.
(RS485 Card Reader Mode)
Flicker Red: Connection Exception.
Access Control Terminal·Quick Start Guide
7
Access Control Terminal·Quick Start Guide

3 Terminal Connection

3.1 Terminal Description

Figure 3-1 Terminal Diagram of Access Control Terminal
8
Line
Group
No.
Function
Color
Termina
l Name
Description
Line
Group
A
A1
Power
Input
Red
+12V
12V DC Power
Supply
A2
Black
GND
GND
Line
Group
B
B1
Alarm
Input
Yellow/Blue
IN1
Alarm Input 1
B2
Yellow/Black
GND
GND
B3
Yellow/Orange
IN2
Alarm Input 2
B4
Alarm
Output
Yellow/Purple
NC
Alarm Output
Wiring
B5
Yellow/Brown
COM
B6
Yellow/Red
NO
Line
Group
C
C1
RS485
Commun
ication
Port
Yellow
485 +
RS485 Wiring
C2
Blue
485 -
C3
Wiegand
Output
Green
W0
Wiegand Wiring 0
C4
White
W1
Wiegand Wiring 1
Access Control Terminal·Quick Start Guide
Table 3-1 Terminal Description
9
Line
Group
No.
Function
Color
Termina
l Name
Description
C5
Orange
LED-ERR
Error Prompt LED
Indicator Wiring
C6
Purple
BEEP
Beep Siren Wiring
C7
Grey
TAMPER
Tampering Alarm
Wiring
Line
Group
D
D1
Power
Output
Red
+12V
Power Output
D2
Black
GND
GND
D3
Door
Lock
White/Purple
NC
Lock Wiring
D4
White/ Yellow
COM
D5
White/Red
NO
D6
Yellow/Green
SENSOR
Door Contact Signal
Input
Access Control Terminal·Quick Start Guide
10
Loading...
+ 40 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use