Hangzhou Hikvision Digital Technology K1802MK User Manual

DS-K1802 Series Card Reader

User Manual

DS-K1802 Series Card Reader

i

User Manual

© 2019Hangzhou Hikvision Digital Technology Co., Ltd.

About this Manual

This Manual is applicable to DS-K1802series card reader
This Manual is subject to domestic and international copyright
protection. Hangzhou Hikvision Digital Technology Co., Ltd.
("Hikvision") reserves all rights to this manual. This manual cannot
be reproduced, changed, translated, or distributed, partially or
wholly, by any means, without the prior written permission of
Hikvision.
Please use this user manual under the guidance of professionals.

Trademarks

and other Hikvision’s trademarks and logos are the

properties of Hikvision in various jurisdictions. Other trademarks
and logos mentioned below are the properties of their respective
owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND

FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,

AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY,
SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE,
AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE
LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL,
OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR
LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE
USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF

DS-K1802 Series Card Reader

ii

THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE
OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION
SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING
FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR
OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS
PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND
THE APPLICABLE LAW, THE LATER PREVAILS.

DS-K1802 Series Card Reader

iii

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
The device must not be co-located or operating in conjunction
with any other antenna or transmitter.
This equipment should be installed and operated with a minimum
distance 20cm between the radiator and your body.

FCC Conditions

DS-K1802 Series Card Reader

iv

This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied
accessories too are marked with "CE" and
comply therefore with the applicable
harmonized European standards listed under

the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products
marked with this symbol cannot be disposed
of as unsorted municipal waste in the
European Union. For proper recycling, return
this product to your local supplier upon the

purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information
see: www.recyclethis.info.

2006/66/EC (battery directive): This product

contains a battery that cannot be disposed

of as unsorted municipal waste in the

European Union. See the product

documentation for specific battery

information. The battery is marked with this

symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper
recycling, return the battery to your supplier or to a designated
collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

DS-K1802 Series Card Reader

v

This device meets the CAN ICES-3 (A)/NMB-3(A) standards
requirements.

Use only power supplies listed in the user instructions:

Model

Manufacturer

Standard

TS-A018-120015Ec

Shenzhen Transin

Technologies Co., Ltd

CEE

Safety Instruction

These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious
injury or death.
Cautions: Neglecting any of the cautions may cause injury or
equipment damage.

Warnings

 All the electronic operation should be strictly compliance with the

electrical safety regulations, fire prevention regulations and
other related regulations in your local region.

 Please use the power adapter, which is provided by normal

company. The power consumption cannot be less than the
required value.

Warnings Follow these
safeguards to prevent
serious injury or death.

Cautions Follow these
precautions to prevent potential
injury or material damage.

DS-K1802 Series Card Reader

vi

 Do not connect several devices to one power adapter as adapter

overload may cause over-heat or fire hazard.

 Please make sure that the power has been disconnected before

you wire, install or dismantle the device.

 When the product is installed on wall or ceiling, the device shall be

firmly fixed.

 If smoke, odors or noise rise from the device, turn off the power

at once and unplug the power cable, and then please contact the
service center.

 If the product does not work properly, please contact your dealer

or the nearest service center. Never attempt to disassemble the
device yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)

Cautions

 Do not drop the device or subject it to physical shock, and do not

expose it to high electromagnetism radiation. Avoid the
equipment installation on vibrations surface or places subject to
shock (ignorance can cause equipment damage).

 Do not place the device in extremely hot (refer to the specification

of the device for the detailed operating temperature), cold, dusty
or damp locations, and do not expose it to high electromagnetic
radiation. The appropriate temperature is -20℃ to 65℃.

 The device cover for indoor use shall be kept from rain and

moisture.

 Exposing the equipment to direct sun light, low ventilation or heat

source such as heater or radiator is forbidden (ignorance can
cause fire danger).

 Do not aim the device at the sun or extra bright places. A

blooming or smear may occur otherwise (which is not a
malfunction however), and affecting the endurance of sensor at
the same time.

DS-K1802 Series Card Reader

vii

 Please use a soft and dry cloth when clean inside and outside

surfaces of the device cover, do not use alkaline detergents.

 Please keep all wrappers after unpack them for future use. In case

of any failure occurred, you need to return the device to the
factory with the original wrapper. Transportation without the
original wrapper may result in damage on the device and lead to
additional costs.

 Improper use or replacement of the battery may result in hazard

of explosion. Replace with the same or equivalent type only.
Dispose of used batteries according to the instructions provided
by the battery manufacturer.

Preventive and Cautionary Tips

To guarantee the card reader works properly, please read and
obey the notes below.
 If the card reader is powered by the controller, the power

supply distance is recommended to be no longer than 100m.
If the distance is longer than 100m, you are advised to power
the card reader by external 12V (range: -%10 ~ +%10) DC
power supply, which is nonswitched and linear.

 To guarantee the communication between the controller and

the card reader, you must use RVVP cable above 0.5 to
connect them.

 If the card reader is installed outside or in environment easy

to permeable, it is advisable to install a waterproof shield.

 If you need to install several card readers, the distance

among them must over 30cm.

 To reduce the noise in long distance transmission, the shield

of cable should connect to the GND of both controller and
card reader terminal.

 Please take care of your card and report card loss in time

when card is lost.

DS-K1802 Series Card Reader

viii

 If you require a higher security level, use multiple

authentication modes.

 Multiple card types are supported. Please select an

appropriate card type according to the card performance and
the usage scenarios.

DS-K1802 Series Card Reader

ix

Content

Chapter 1 Introduction ........................................................ 2

1.1 Over View ...................................................................... 2

1.2 Indicator and Component .............................................. 3

Chapter 2 Installation .......................................................... 3

2.1 Definition of Cable ......................................................... 3

2.2 W iring Cables ................................................................ 4

2.3 Installing Card Reader .................................................... 4

Chapter 3 Sound Prompt and Indicator ................................ 6

DS-K1802 Series Card Reader

2

Chapter 1 Introduction

1.1 Over View

DS-K1802EK/MK/SK

DS-K1802E/M/S

Figure 1-1 DS-K1802 Series Card Reader

DS-K1802 series card reader is a kind of high-performance
product. It communicates with access controller via Wiegand
protocol. As to the physical appearance, the PC+ABS material
makes water proof and dust proof possible in poor environment.

DS-K1802 Series Card Reader

3

1.2 Indicator and Component

Figure 1-2 Indicator and Component

Chapter 2 Installation

2.1 Definition of Cable

The description of cables is shown below.

Table 2-1 Description of Cable

Color

Description

Red

PWR (+12 VDC)

Black

GND

Purple

Beep Control

Brown

OK

Orange

ERR

Green

Wiegand W0

DS-K1802 Series Card Reader

4

Color

Description

White

Wiegand W1

Blue

Wiegand 26/ 34

2.2 Wiring Cables

Purpose:

Wire the cables between controller and card reader, thus to

establish the communication between them.

Steps for Wiegand communication mode:

1. Set the Wiegand mode before power-on:

Cable

Wiring Method

Wiegand Mode

Blue Wiegand Cable

Grounded

Wiegand 26

Not Grounded

Wiegand 34

2. Wiring the cable between controller and card reader as

shown below.

Black

Red

Green

White

Purple

Orange

Brown

Card Reader

ERR

OK

Figure 2-1 Wiring for Wiegand Communication Mode

2.3 Installing Card Reader

Steps:

DS-K1802 Series Card Reader

5

1. Fix the plate on the wall or

other places by using two

screws (PA4×25-SUS). Make

sure the arrows on the plate are

upwards.

2. Check whether the plate is fixed

and in the right direction.

3. Slide the card reader from the

direction A to B along the plate

side until the bottom matches

the joint. Make sure the card

reader is tightly on the wall or

other places.

4. Drag and move the card reader

to make sure it is fixed.

DS-K1802 Series Card Reader

6

Chapter 3 Sound Prompt and Indicator

After the card reader is powered on, LED status indicator will turn
green and blink for 1 time. Then it will turn red and blink for 3
times. At last the buzzer will send out a beep sound indicating the
starting up process is completed.
When using the card reader, it will send out different sounds
prompt and the LED indicator to indicate different statuses. You
can refer to tables below for detailed information.

Table 1-1 Description of Prompt Sound

Sound Prompt

Description

One beep

Swiping card prompt

Pressing keys prompt

Prompt for too long card No. input by
pressing keys.

Time out prompt for pressing keys or
swiping card.

For Card + Password authentication:
prompt for entering the password after
swiping the card.

Two rapid beeps

The operation of pressing keys or swiping
card is valid.

Three slow beeps

The operation of pressing keys or swiping
card is invalid.

Rapidly
continuous beeps

Prompt for tamper-proof alarm.

Prompt for buzzer alarm.

Slowly continuous
beeps

The card reader is unencrypted.

DS-K1802 Series Card Reader

7

Table 1-2 Description of LED Indicator

LED Indicator Status

Description

Green (blink for 1
time), and red (blink
for 3 times)

The card reader is power on.

Green and slow
blinking

For Card + Password authentication:
prompt for entering the password after
swiping the card.

Solid green for 3s

The operation of pressing keys or swiping
card is valid.

Solid red

Card reader is working normally.

Red and blink for 3
times

The operation of pressing keys or swiping
card is invalid.

0200001090515

DS-K1802 Series Card Reader

8

UD05260B-A