Hangzhou Hikvision Digital Technology K1107MK User Manual

DS-K1107 Series Card Reader

User Manual

DS-K1107 Series Card Reader

i

User Manual

© 2019 Hangzhou Hikvision Digital Technology Co., Ltd.

About this Manual

This Manual is applicable to DS-K1107 series card reader
This Manual is subject to domestic and international copyright
protection. Hangzhou Hikvision Digital Technology Co., Ltd.
("Hikvision") reserves all rights to this manual. This manual cannot
be reproduced, changed, translated, or distributed, partially or
wholly, by any means, without the prior written permission of
Hikvision.
Please use this user manual under the guidance of professionals.

Trademarks

and other Hikvision’s trademarks and logos are the

properties of Hikvision in various jurisdictions. Other trademarks
and logos mentioned below are the properties of their respective
owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND

FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,

AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY,
SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE,
AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE
LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL,
OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR
LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE
USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF

DS-K1107 Series Card Reader

ii

THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE
OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION
SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING
FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR
OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS
PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND
THE APPLICABLE LAW, THE LATER PREVAILS.

DS-K1107 Series Card Reader

iii

Regulatory Information
FCC Information

Please take attention that changes or modification not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
The device must not be co-located or operating in conjunction
with any other antenna or transmitter.
This equipment should be installed and operated with a minimum
distance 20cm between the radiator and your body.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is

DS-K1107 Series Card Reader

iv

subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the
applicable harmonized European
standards listed under the RE Directive

2014/53/EU, the EMC Directive
2014/30/EU, the LVD Directive 2014/35/EU, the
RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new
equipment, or dispose of it at designated
collection points. For more information see:

www.recyclethis.info.

2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of
as unsorted municipal waste in the European
Union. See the product documentation for
specific battery information. The battery is
marked with this symbol, which may include

DS-K1107 Series Card Reader

v

lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For
proper recycling, return the battery to your supplier or to a
designated collection point. For more information see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards
requirements.

Use only power supplies listed in the user instructions:

Model

Manufacturer

Standard

TS-A018-120015Ec

Shenzhen Transin

Technologies Co., Ltd

CEE

Safety Instruction

These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious
injury or death.
Cautions: Neglecting any of the cautions may cause injury or

equipment damage.

Warnings

Warnings Follow these
safeguards to prevent
serious injury or death.

Cautions Follow these
precautions to prevent potential
injury or material damage.

DS-K1107 Series Card Reader

vi

 All the electronic operation should be strictly compliance with

the electrical safety regulations, fire prevention regulations and
other related regulations in your local region.

 Please use the power adapter, which is provided by normal

company. The power consumption cannot be less than the
required value.

 Do not connect several devices to one power adapter as

adapter overload may cause over-heat or fire hazard.

 Please make sure that the power has been disconnected before

you wire, install or dismantle the device.

 When the product is installed on wall or ceiling, the device shall

be firmly fixed.

 If smoke, odors or noise rise from the device, turn off the

power at once and unplug the power cable, and then please
contact the service center.

 If the product does not work properly, please contact your

dealer or the nearest service center. Never attempt to
disassemble the device yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.)

Cautions

 Do not drop the device or subject it to physical shock, and do

not expose it to high electromagnetism radiation. Avoid the
equipment installation on vibrations surface or places subject to
shock (ignorance can cause equipment damage).

 Do not place the device in extremely hot (refer to the

specification of the device for the detailed operating
temperature), cold, dusty or damp locations, and do not expose
it to high electromagnetic radiation. The appropriate
temperature is -20℃ to 65℃.

DS-K1107 Series Card Reader

vii

 The device cover for indoor use shall be kept from rain and

moisture.

 Exposing the equipment to direct sun light, low ventilation or

heat source such as heater or radiator is forbidden (ignorance
can cause fire danger).

 Do not aim the device at the sun or extra bright places. A

blooming or smear may occur otherwise (which is not a
malfunction however), and affecting the endurance of sensor at
the same time.

 Please use the provided glove when open up the device cover,

avoid direct contact with the device cover, because the acidic
sweat of the fingers may erode the surface coating of the device
cover.

 Please use a soft and dry cloth when clean inside and outside

surfaces of the device cover, do not use alkaline detergents.

 Please keep all wrappers after unpack them for future use. In

case of any failure occurred, you need to return the device to
the factory with the original wrapper. Transportation without
the original wrapper may result in damage on the device and
lead to additional costs.

 Improper use or replacement of the battery may result in

hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.

Preventive and Cautionary Tips

To guarantee the card reader works properly, please read and
obey the notes below.
 If the card reader is powered by the controller, the power

supply distance is recommended to be no longer than 100m.
If the distance is longer than 100m, you are advised to power
the card reader by external 12V (range: -%10 ~ +%10) DC

DS-K1107 Series Card Reader

viii

power supply, which is nonswitched and linear.

 To guarantee the communication between the controller and

the card reader, you must use RVVP cable above 0.5 to
connect them.

 If the card reader is installed outside or in environment easy

to permeable, it is advisable to install a waterproof shield.

 If you need to install several card readers, the distance

among them must over 30cm.

 To reduce the noise in long distance transmission, the shield

of cable should connect to the GND of both controller and
card reader terminal.

 Please take care of your card and report card loss in time

when card is lost.

 If you require a higher security level, use multiple

authentication modes.

 Multiple card types are supported. Please select an

appropriate card type according to the card performance and
the usage scenarios.

DS-K1107 Series Card Reader

ix

Content

Chapter 1 Introduction ...................................................... 10

1.1 Over View .................................................................... 10

1.2 Indicator and Component ............................................ 11

Chapter 2 Installation ........................................................ 12

2.1 Introduction for DIP Switch ......................................... 12

2.2 Definition of Cable ....................................................... 13

2.3 Wiring Cables .............................................................. 13

2.4 Installing Card Reader .................................................. 15

Chapter 3 Sound Prompt and Indicator .............................. 16

DS-K1107 Series Card Reader

10

Chapter 1 Introduction

1.1 Over View

Figure 1-1 DS-K1107 Series Card Reader

DS-K1107 series card reader is a kind of high-performance
product, with a 32 bit high-speed processor. It communicates with
access controller via either RS-485 protocol (AES encrypted) or
Wiegand protocol. And a build-in tamper-proof module helps to
protect card reader from malicious damage. As to the physical
appearance, the PC+ABS material makes water proof and dust
proof possible in poor environment.

DS-K1107 Series Card Reader

11

1.2 Indicator and Component

Figure 1-2 2.2 Indicator and Component

DS-K1107 Series Card Reader

12

Chapter 2 Installation

2.1 Introduction for DIP Switch

The DIP switch module is shown below. The No. of DIP switch

from left to right is 1 ~ 8.

Figure 2-1 DIP Switch Module

Table 2-1 Description of DIP Switch

Icon

Description

Represent 1 in binary mode

Represent 0 in binary mode

For example, binary value of the following status is: 0000 1100.

Figure 2-2 DIP Switch Module

Table 2-2 Description of DIP Switch

No.

Description

DIP Switch Status

1 ~ 4

Address of RS-485

1: 1
0: 0

5

Reserved

Reserved

6

Wiegand protocol or RS-485

1: Wiegand protocol;

DS-K1107 Series Card Reader

13

No.

Description

DIP Switch Status

protocol.

0: RS-485 protocol.

7

Wiegand Protocol
(available when No. 6 is 1)

1: Wiegand protocol
of 26-bit;
0: Wiegand protocol
of 34-bit.

8

Matched Resistance
(available for RS-485 protocol)

1: Enable;
0: Disable.

2.2 Definition of Cable

The description of 10 cables is shown below.

Table 2-3 Description of Cable

Color

Description

Orange

Red LED Control (available for Wiegand Protocol)

White

Wiegand W1 (available for Wiegand Protocol)

Green

Wiegand W0 (available for Wiegand Protocol)

Blue

RS-485-

Yellow

RS-485+

Red

PWR (+12 VDC)

Black

GND

Gray

TAMPER (available for Wiegand Protocol)

Purple

Beep Control (available for Wiegand Protocol)

Brown

Green LED Control (available for Wiegand
Protocol)

2.3 Wiring Cables

Purpose:

Wire the cables between controller and card reader, thus to

DS-K1107 Series Card Reader

14

establish the communication between them.

Steps for RS-485 communication mode:

1. Set the DIP switch of No. 6 as 0.

2. Set the DIP switch of No. 1 ~ 4 for RS-485 address and

reading card mode. For details, please refer to 2.1
Introduction for DIP Switch.

3. Wire the cable between controller and card reader as

shown below.

Yellow

Blue

Black

Red

Black

Red

Green

White

Purple

Orange

Brown

Controller

Card Reader

Card Reader

Card Reader

Green

Figure 2-3 Wiring for RS-485 Communication Mode

Steps for Wiegand communication mode:

1. Set the DIP switch of No. 6 as 1.

2. Set the DIP switch of No. 7 for reading card mode and

Wiegand protocol. For details, please refer to 2.1
Introduction for DIP Switch.

3. Wiring the cable between controller and card reader as

DS-K1107 Series Card Reader

15

shown below.

Black

Red

Green

White

Purple

Orange

Brown

Card Reader

Green

Figure 2-4 Wiring for Wiegand Communication Mode

2.4 Installing Card Reader

Before you start:

Set the DIP switch. For details, refer to 2.1 Introduction for DIP
Switch.

DS-K1107 Series Card Reader

16

Installation for DS-K1101/ 02/ 03/ 04 series card reader
Steps:

1. F ix the plate on the wall or

other places by using two

screws (PA4×25-SUS). Make

sure the arrows on the plate

are upwards.

2. Check whether the plate is

fixed and in the right direction.

3. Slide the card reader from the

direction A to B along the

plate side until the bottom

matches the joint. Make sure

the card reader is tightly on

the wall or other places.

4. Drag and move the card

reader to make sure it is fixed.

Chapter 3 Sound Prompt and Indicator

After the card reader is powered on, LED status indicator will turn
green and blink for 1 time. Then it will turn red and blink for 3

DS-K1107 Series Card Reader

17

times. At last the buzzer will send out a beep sound indicating the
starting up process is completed.
When using the card reader, it will send out different sounds
prompt and the LED indicator to indicate different statuses. You
can refer to tables below for detailed information.

Table 1-1 Description of Prompt Sound

Sound Prompt

Description

One beep

Swiping card prompt

Pressing keys prompt

Prompt for too long card No. input by
pressing keys.

Time out prompt for pressing keys or
swiping card.

For Card + Fingerprint authentication:
prompt for pressing the fingerprint after
swiping the card.

Two rapid beeps

The operation of pressing keys or swiping
card is valid.

Three slow beeps

The operation of pressing keys or swiping
card is invalid.

Rapidly
continuous beeps

Prompt for tamper-proof alarm.

Prompt for buzzer alarm.

Slowly continuous
beeps

The card reader is unencrypted.

DS-K1107 Series Card Reader

18

Table 1-2 Description of LED Indicator

LED Indicator Status

Description

Green (blink for 1
time), and red (blink
for 3 times)

The card reader is power on.

Green and blinking

For Card + Fingerprint authentication:
prompt for pressing the fingerprint after
swiping the card.

The operation of configuring the
fingerprint.

Solid green for 2s

The operation of pressing keys or swiping
card is valid.

Solid red

Card reader is working normally.

Red and blink for 3
times

The operation of pressing keys or swiping
card is invalid.

Red and blinking

For RS-485 protocol: Registering failed or
card reader is offline.

0200001090312

DS-K1107 Series Card Reader

19

UD05519B-A