Hangzhou Hikvision Digital Technology K1102MK, K1103MK, K1101MK, K1104MK, K1102EK User Manual

DS-K1100 Series Card Reader

User Manual

DS-K1100 Series Card Reader

User Manual

Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology C o., Ltd. or its

subsidiaries (hereinafter referred to be “Hikvision”). This user ma nual (hereinafter referred to be “the Manual”) cannot be reproduced, changed,

translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. This Manual is applicable to card reader.

Series Models Description

DS-K1101 Series

DS-K1102 Series

DS-K1103 Series

DS-K1104 Series

About this Manual

This Ma nual is subject to domestic and international copyright protection.

Hangzhou Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all

DS-K1101M Card Reader DS-K1101MK DS-K1101C DS-K1101CK DS-K1102M DS-K1102MK DS-K1102C DS-K1102CK DS-K1102E DS-K1102 EK DS-K1102 EM DS-K1102 EMK DS-K1103M DS-K1103MK DS-K1103C DS-K1103CK DS-K1104M DS-K1104MK DS-K1104C DS-K1104CK

Card Reader

DS-K1100 Series Card Reader

rights to this man ual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.

Trademarks

properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFT WARE AND FIRMWARE, IS PROVIDED "AS IS", WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AN D NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIA L, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WI TH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

and other Hikvision’s trademarks and logos are the

DS-K1100 Series Card Reader

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly approved

by the party responsible for compliance could void the user’s authority to

operate the equipment.

FCC compliance: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

The device must not be co-located or operating in conjunction with any

other antenna or transmitter.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is s ubject to

the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference

that may cause undesired operation

iii

DS-K1100 Series Card Reader

EU Conformity Statement

2014/30/EU, the LVD Directive 2014/35/EU, the RoHS

Directive 2011/65/EU.

For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

This product and - if applicable - the supplied

accessories too are marked with "CE" and

comply therefore with the applicable

harmonized European standards listed under

the RE Directive 2014/53/EU, the EMC Directive

2012/19/EU (WEEE directive): Products marked

with this symbol cannot be disposed of as

unsorted municipal waste in the European Union.

For proper recycling, return this product to your

local supplier upon the purchase of equivalent

new equipment, or dispose of it at designated

collection points. For more information see:

www.recyclethis.info.

2006/66/EC (battery directive): This product

contains a battery that cannot be disposed of as

unsorted municipal waste in the European Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

DS-K1100 Series Card Reader

Use only power supplies listed in the user instructions:

Model

Manufacturer

Standard

TS-A018-120015Ec

Shenzhen Transin

Technologies Co., Ltd

CEE

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage.

Warnings

 All the electronic operation should be strictly compliance with the

electrical safety regulations, fire prevention regulations and other related regulations in your local region.

 Please use the power adapter, which is provided by normal company. The

power consumption cannot be less than the required value.

 Do not connect several devices to one power adapter as adapter overload

may cause over-heat or fire hazard.

 Please make sure that the power has been disconnected before you wire,

install or dismantle the device.

 When the product is installed on wall or ceiling, the device shall be firmly

fixed.

Warnings Follow these safeguards to prevent serious injury or death.

Cautions Follow these precautions to prevent potential injury or m aterial damage.

DS-K1100 Series Card Reader

 If smoke, odors or noise rise from the device, turn off the power at once

and unplug the power cable, and then please contact the service center.

 If the product does not work properly, please contact your dealer or the

nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)

Cautions

 Do not drop the device or subject it to physical shock, and do not expose

it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).

 Do not place the device in extremely hot (refer to the specification of the

device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. The appropriate temperature is -20℃ to 65℃.

 The device cover for indoor use shall be kept from rain and moisture.  Exposing the equipment to direct sun light, low ventilation or heat source

such as heater or radiator is forbidden (ignorance can cause fire danger).

 Do not aim the device at the sun or extra bright places. A blooming or

smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.

 Please use the provided glove when open up the device cover, avoid direct

contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.

 Please use a soft and dry cloth when clean inside and outside surfaces of

the device cover, do not use alkaline detergents.

 Please keep all wrappers after unpack them for future use. In case of any

failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs.

 Improper use or replacement of the battery may result in hazard of

explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.

Preventive and Cautionary Tips

DS-K1100 Series Card Reader

vii

To guarantee the card reader works properly, please read and obey the

notes below.  If the card reader is powered by the controller, the power supply

distance is recommended to be no longer t han 100m. If the distance is

longer than 100m, you are advised to power the card reader by

external 12V (range: -%10 ~ +%10) DC power supply, which is

nonswitched and linear.

 To guarantee the communication between the controller and the card

reader, you must use RVVP cable above 0.5 to connect them.

 If the card reader is installed outside or in environment easy to

permeable, it is advisable to install a waterproof shield.

 If you need to install se veral card readers, the distance among them

must over 30cm.

 To reduce the noise in long distance transmission, the shield of cable

should connect to the GND of both controller and card reader

terminal.

 Please take care of your card and report card loss in time when card is

lost.

 If you require a higher security level, use multiple authentication

modes.

 Multiple card types are supported. Please select an appropriate card

type according to the card performance and the usage scenarios.

+ 16 hidden pages