Hangzhou Hikvision Digital Technology H2TS03 User Manual

Handheld Thermal
Monocular
User Manual
UD06410B
0100001070725
COPYRIGHT © 2017 Hikvision. ALL RIGHTS RESERVED
About This Manual
COPYRIGHT ©2017 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology
Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be
reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual.
This Manual is applicable to Handheld Thermal Monocular. The Manual includes instructions for using and managing the product.
Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the
properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH
ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
Handheld Thermal Monocular
User Manual
.
UD06410B
0100001070725
COPYRIGHT © 2017 Hikvision. ALL RIGHTS RESERVED
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation.
Cet appareil est conforme à la section 15 des réglementations de la FCC. Le fonctionnement de l’appareil est sujetaux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d’interférences néfastes, et (2) cet appareil doit tolérer les interférences reçues, y compris celles
qui risquent de provoquer un fonctionnement indésirable.
Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
EU Conformity Statement
This product and, if applicable, the supplied accessories are marked with “CE” and comply therefore with the applicable harmonized
European standards listed under the Radio Equipment Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. Fo r more information see: www.recyclethis.info.
After the laboratory measurement, the Max SAR value is 0.192W/kg for 2.4G Band which satisfies the RF exposure requirement
WARNINGS AND CAUTIONS
All the electronic operation should be strictly compliance with
the electrical safety regulations, fire prevention regulations and other related regulations in your local region.
Please use the power adapter, which is provided by normal
company. The power consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter
overload may cause over-heat or fire hazard.
Do not drop the device or subject it to physical shock, and do not
expose it to high electromagnetism radiation. Avoid the device installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the
specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.
The device cover for indoor use should be kept from rain and
moisture.
Exposing the device to direct sun light, low ventilation or heat
source such as heater or radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A
blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
For long-term storage of the battery, make sure you fully charge it every half year, to ensure the battery quality. Otherwise, you may damage the battery.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1 Introduction
1.1 Box Content
Non-dust
Cloth (×1)
USB Cable
(×1)
Manual (×1)
Protective
Bag (×1)
Handheld Thermal
Monocular (×1)
Neck
Belt(×1)
1.2 Overview
The handheld thermal monocular is a handheld thermal camera with functions of observation, hot spot mark, distance measurement, Wi-Fi hot spot, and so on. The high-sensitivity built-in IR detector provides you with clear view even in total darkness.
1.3 Features
High performance chip, and DDE
(Digital Detail Enhancement) technique
1024 × 768 Resolution OLED display Built-in rechargeable Li-ion battery Up to five hours continuous running
(GPS function and Wi-Fi hot spot function off)
USB Cable Small in size and light in weight
1.4 Functions
Distance Measurement: The device realizes distance measurement
function after marking the top and bottom of target, and input the target height.
Hot Spot Mark: The device detects and marks the hot spot of
highest temperature. Wi-Fi Hot Spot:
Device can capture snapshots, record videos, and set parameters via APP after being connected to your phone.
GPS Function: The device can be located with GPS system. Mode Switch: Device supports pallet switch and distance
measurement. Storage: Built-in memory module supports video
recording/snapshot capturing. Digital Zoom: Device supports 1× and 2× digital zoom. LED light: LED light supplement makes the device a torch
in the wild field.
2 Appearance
2.1 Dimensions
Take the figure below for the dimensions of the handheld thermal monocular.
57.6mm (2.27″)
51.9mm (2.04″)
189.4mm (7.46)
65.9mm (2.59″)
73.7mm (2.90″)
2.2 Buttons and Interfaces
Take the figure below for the buttons and interfaces description of handheld thermal monocular.
1
LED Light
LED Indicator
But tons
Power
Press: LED Light Supplement On/Off
Hold: Power On/Off
MOD
MODE
Press: Switch Pallet Hold: Distance Measure On/Off
Capture
Press: Capture Snapshot Hold: Start/Stop Record Video
Menu
Press: Shutter Release Hold: Menu Operation
Zoom ±
Press: Digital Zoom Hold: Reserved
USB Interface
Tripod Screw
Focus Knob
Eyepiece
Lens Cover
Lens Cover
Cover the lens when you are not using the monocular.
LED Indicator
When the LED indicator is on: the device is activating, and after the activation, the LED indicator turns off and the device is on.
Sight Adjust Knob
Slide the sight adjust knob to adjust the view according to your
degree of myopia.
USB Interface
Charge the battery and export videos/snapshots with the USB cable.
Note: For detailed operations of the menu, refer to Menu Operation Section.
3 Basic Operations
3.1 Charging the Monocular
Note: Please charge the monocular with the delivered USB cable and power adapter. The charging temperature should be 0 °C to 45 °C (32 °F to 113 °F).
Steps:
1. Lift the USB cover.
USB Interface
Battery Status Indicator
2. Plug in the USB cable and connect the
other terminal into the power adapter.
3. Plug the power adapter to the power
source.
When the monocular is turned on, the OSD (on-screen display) shows the battery status. When you see the Low Battery status, charge the monocular and ensure it’s working properly.
Battery LED Indicator Status
Red Flash
Error occurred.
Solid Red
Battery is properly charged.
Solid Green
Battery is fully charged.
Off
Battery is not charged.
3.2 Power On and Off
Power On Hold the POWER button for four seconds and
the LED indicator in the front turns green. After the device is powered on, the indicator keeps green.
Power LED Indicator
Refer to the figure below for the main view of the monocular.
Wi-Fi Hot Spot
Digital Zoom
Storage
Battery
Power Off When the monocular is turned on, hold the
POWER button for four seconds to power off the device.
3.3 Thermal View Observation
Steps:
1. Power on the monocular.
2. Hold the monocular and make sure the
eyepiece covers your eye.
3. Slide the sight adjust knob to adjust the
diopter until the OSD text or image is clear.
Sight Adjust Knob
Note: You must perform the sight adjustment before any further use of the monocular.
4. Point the monocular towards the target of
the view.
3.4 Basic Operation
Connect the thermal monocular to your PC with USB cable, you can export the recorded videos and captured snapshots.
Steps:
1. Hold the button to enter the menu
and select the icon .
2. Press and the icon turns to and
the Wi-Fi hot spot function is disabled.
3. Connect the thermal monocular to your
PC with USB cable, you can see a detected removable disk.
Notes:
When you connect the device to
PC for the first time, it installs the drive program automatically.
When you connect the device to
PC, the device displays images, but functions such as recording, capturing and Wi-Fi hot spot are disabled.
File Export
Steps:
1. Connect the thermal monocular to your
PC with USB cable and open the detected disk.
2. Enter DCIM>100EZVIZ to view the
videos and snapshots.
- Select and copy the videos to PC
and play the file with the player.
- Select and copy the snapshots to PC
and view the files.
3. Disconnect the device from your PC. Upgrade
Steps:
1. Connect the thermal monocular to your
PC with USB cable and open the detected disk.
2. Copy the upgrade file and paste it to the
root directory of the device.
3. Disconnect the device from your PC.
4. Reboot the monocular and the device
upgrades automatically. The upgrading process will be displayed in the main interface.
4 Main Function
4.1 Menu Operation
When the monocular is turned on, hold the button for three seconds to display the OSD menu.
OK
Press the button to move the cursor up, and press the button to move the cursor down. Press the button to confirm.
Press to display or hide the OSD information.
Press to enable/disable hot spot mark ( marking the spot of highest temperature).
Press to enable or disable the Wi-Fi hot spot. Connect your phone to the monocular via the Wi-Fi and record/capture with App.
Press to exit the menu operation interface.
Press to enter distance measurement mode. For details, refer to Section 0.
Press to enable or disable the GPS function.
Press to adjust the brightness. The icons on the left indicate: high Brightness, medium Brightness, and low Brightness.
Press to view the version number and serial number.
Press to restore all parameters to default settings.
Palette Settings Under the same scene, you can select different palettes to
see the scene in different effects.
White Hot:
The hot part is light-colored in view.
Black Hot: The hot part is black-colored in
view.
Fusion: The hot part is yellow-colored
and cold part is purple-colored in view.
Red Hot:
The hot part is red-colored in view.
Brightness Adjusting In white hot mode, you can adjust the brightness as >
> to adjust the image darker and darker.
In black hot mode, the brightness of the image turns in the opposite way.
4.2 Distance Measurement
Before you start:
In the view node, you can hold the button to enter the distance measurement mode.
Or, you can hold the button to enter the menu and select to enter the distance measurement mode.
Purpose:
You can mark the top and bottom of the target in the distance to calculate the distance in between.
Steps:
1. Enter the distance measurement mode.
You can refer to before you start part above.
2. Define the target height. a) Press to enter the height
setting interface.
b) Select target from Deer, Wolf,
Bear, and Custom.
c) Press and to select the
target height and press to confirm (for Deer, Wolf, or Bear).
d) Press and to select the
target height, the available height ranges from 0.3 m to 9.9 m (for Custom).
3. Set the top of the target. a) Move the monocular slightly to
place the mark above the target top.
b) Press to confirm.
4. Set the bottom of the target. a) Move the monocular slightly to
place the mark below the target bottom.
b) Press to confirm.
The distance between you and the target will display on the upper left corner of the live view interface.
Note: Enter the distance measurement interface, press to view the measured distance.
4.3 Hot Spot Mark
In the menu, select / and press to enable/disable hot spot mark (marking the spot of highest temperature).
When the hot spot mark is enabled, the mark displays in the spot of the highest temperature. When the scene changes, the mark moves.
4.4 Record/Capture
Video Recording In the view mode, hold the button for
three seconds, and the monocular starts to record. In the upper left corner, the recording time displays.
After recording the video, hold the button for three seconds again, and the monocular stops recording.
Snapshot Capturing In the view mode, press the button, the
live view freezes for one second, and the snapshot is captured.
4.5 Digital Zoom
Press the button in the view mode, the live view will switch between 1× digital zoom and 2× digital zoom.
4.6 Shutter Release
In the view mode, press the button once to release the shutter once.
4.7 Others
LED Light Supplement Press the button to enable/disable the
LED light supplement. Wi-Fi Hot Spot Connect your phone to the Wi-Fi hot spot of
the monocular, you can configure the parameters and realize functions of the device.
Steps:
1. Search the “EZVIZ SPORTS” on App
Store (iOS System) or Google Play TM (Android System) to download and install the app.
2. Turn on the WLAN and connect to the
Wi-Fi.
- Wi -Fi Name: HIK-IPTS Serial No.
- Wi -Fi Password: Serial No.
3. Open the APP and set parameters.
- Select Video and tap record key to
record videos.
- Select Photo and tap capture key to
capture snapshot.
- Tap on to enter the Camera
Settings interface and edit the Wi-Fi hot spot name and password.
5 FAQ
Q: The charge indicator flashes
improperly.
A: Examine whether the device is charged
with standard power adapter and the charging temperature is 0 °C to 45 °C
(32 °F to 113 °F).
Q: Device power indicator is off.
A: Examine whether the device is
off-battery.
Q: The image of the monocular is not
clear.
A: Perform the sight adjustment referring
to section 3.3.
Q: Wi-Fi is not found.
A: Examine whether the Wi-Fi function is
turned on. If not, go to OSD menu and
turn on Wi-Fi.
Q: Capturing or recording fails.
A: Examine the items below:
1. Whether the device is connected to
your PC and disabled the capturing and
recording.
2. Whether the storage space is full.
3. Whether the device is low-battery.
Q: There is no GPS signal.
A: Examine the using environment. If the
device receives no signal in indoor
environment, please go to outdoor
spaces. It takes about 10 min to power
on and search for the signal.
Q: The PC cannot identify the monocular.
A: Examine the items below:
1. Whether the device is connected to
your PC with standard USB cable.
2. If you use other USB cables, make sure
the cable length is no longer than 1m.
3. Whether the Wi-Fi function is turned
on. If so, go to OSD menu and turn off Wi-Fi.
Loading...