Page 1
FLOOR KIT INSTRUCTIONS
FOR 12x12 and 12x24 BUILDINGS
ACTUAL SIZE • 144” WIDE X 144” DEEP (12x12)
• 144” WIDE X 288” DEEP (12x24)
1-800-437-0784
This instruction may be different from the one specified in Building instruction.
A
B
#16633
02-24-06
Parts Needed:
A
4 - 2x4x48" Bond Boards
B
4 - 2x4x96" Bond Boards
C
10 - 2x4x93" Floor Joists
D
10 - 2x4x45" Floor Joists
3 - 96"x48"x5/8" Floor Panels
E
3 - 48"x47-7/8"x5/8" Floor Panel
F
- 2" and 3" Nails
Section 1
16"
(41 cm)
A
Section 2
16"
(41 cm)
16"
(41 cm)
Typical
D
D
A
CCC
B
16"
(41 cm)
D
D
D
B
C CC C C C C
16"
(41 cm)
B
(4) 3" (7.6 cm)
Nails
at Joint
16"
(41 cm)
144"
(366 cm)
D
A
D
16"
(41 cm)
C
A
D
B
(41 cm)
D
D
16"
(2) 3" (7.6 cm)
A
(41 cm)
Nails
48"
(122 cm)
16"
A
96"
(244 cm)
16"
(41 cm)
NOTE: Part letters are
not stamped on floor
kits.
ASSEMBLY OF 144” X
142-1/8” FLOOR FRAME
A: Section 1 - Position
Bond Boards &
and Floor Joists as
A
B
C
shown.
Using 3” nails, nail twice
through each Bond Board
& into each end of each
B
C
Joist , keeping pieces
A
flush at top and ends, and
maintain 16” spacing as
shown. Where &
B
A
join together use 4-3” nails.
A: Section 2 - Position
A
Bond Boards &
and Floor Joists as
B
D
shown.
Using 3” nails, nail twice
through each Bond Board
& into each end of each
B
D
Joist , keeping pieces
C
flush at top and ends, and
maintain 16” spacing as
shown. Where &
A
A
B
join together use 4-3” nails.
B
B: Attach Section 1 and
Section 2 together with (2)
3” nails between every joist
as shown.
3" Nails
(7.6 cm)
12x12 and 12x24 Floor Instructions
Page 2
12X12 FLOOR KIT INSTRUCTIONS CONTINUED
X
(122 cm)
D
96"
C
Y
X
C: Completed Floor Frame should be positioned at
building site, leveled, using shims between floor
frame and ground before proceeding to Floor
Panel Attachment.
Square frame by making corner-to-corner
measurements (X to X and Y to Y) the same.
Y
FG
E
2" Nails
(5 cm)
144"
(366 cm)
144"
(366 cm)
D: Position Floor Panel 48” x 96” flush to the outside edges of Floor Frame. Position Floor Panel 46-1/8” x 96”
flush to the outside edges of Floor Frame. Position Floor Panel 46-1/8” x 48” flush to the outside edges of Floor
Frame. Secure panels with two 2” nails at outside corners and one 2” nail at other corners.
E
32"
(81 cm)
16"
(41 cm)
Nails every 12" (30 cm) through Floor Panels into all Floor Bond Boards and Floor Joists
E: Position middle Floor Panel 48” x 96” flush against first panel and flush to edges of Floor Frame. Secure panel
with one 2” nail at outside corners.
Position last outside Floor Panel 48” x 96” flush to the outside edges of Floor Frame. Secure panels with two 2”
nails at outside corners and one 2” nail at other corners.
Note: Mark a line on the Floor Panel over the center of each Floor Joist using a pencil and a piece of lumber from
the kit (or use a chalk line) to make nailing easier.
With Floor Panels flush to outside edges of Floor Frame, nail with 2” nails every 12” through Floor Panels into all
Floor Bond Boards and Floor Joists.
Your 12x12 Floor is now complete. If you need a 10x18 floor
positioned and leveled to ground before beginning assembly of your Wooden Storage Building.
E
FG
16"
(41 cm)
E EE
E
E
16"
(41 cm)
see next page for details.
AB
F
G
32"
(81 cm)
16"
(41 cm)
D
Check to be sure it is properly
2" Nails
(5 cm)
12x12 and 12x24 Floor Instructions
Page 3
12x12 AND 12x24 FLOOR KIT INSTRUCTIONS
(CONTINUED)
12x12
FLOOR
D
12x12
FLOOR
(2) 3” nails between every joist as shown
FOR 12 x 24 FLOOR BUILD TWO 12 x 12 FLOORS,
ATTACH PRIOR TO INSTALLING FLOOR DECKING
Your 12 x 24 Floor is now complete.
Check to be sure it is properly positioned and leveled to ground
before beginning assembly of your Wooden Storage Building.
12x12 and 12x24 Floor Instructions
Loading...