Handöl 51, 52T, 54, 52, 53 Installation Instructions Manual
...
INSTRUCTIONS
51 52 52T
53 54 54T
50
GB
Installation
GB
50
Quality approval
The stove has been tested by the
Swedish National Testing and
Research Institute and meets
the applicable regulations for
CE approval and the stricter
requirements for P marking.
Certificate number for
P Marking: 22 03 16.
Manufacturer’s assurance
Manufacture of the product
has taken place in accordance
with those documents which are
the basis for the relevant type
approval certification and the
required manufacturing checks.
Requirements for flue
The chimney must be dimensioned for at least 350° C for
both top connection directly
upwards and connection directly
backwards from the rear of the
stove.
Handöl 50 is the first cast iron
stove in the world to be swan
marked
As the premier stove
manufacturer in Sweden,
we at NIBE Brasvärme are
committed to Swan marking
our stoves. Choosing to Swan
mark our products is one aspect
of our vision to be a company
of the future with equally high
quality standards regarding the
environment.
Certifcate number 378-001.
Certifierad
Certifikat nr
22 03 16
NOTE!
Notify the local building authorities of the new installation
Report installation of a stove to your local authority.
The owner of the house is personally responsible for ensuring
compliance with the mandatory safety requirements and must
have the installation approved by a qualified inspector.
Your local chimney sweep must also be informed about the
installation as this will affect the routines for regular chimneysweeping services.
EU-declaration
of conformity
Product covered by this declaration
Product type Stove fired by fixed fuel
Type designation Handöl 50-series
Type acc. to standard SS-EN 13240
Intended for use Heating of living accomodation
Fuels Wood logs
Special conditions None
Manufacturer
Name NIBE AB/NIBE Brasvärme
Address Box 134, Skulptörvägen 10, SE-285 23 MARKARYD
Place of manufacture Markaryd
Manufacturing check by approved organisation
Name Swedish National Testing and Research Institute AB
Address Box 857, SE-501 15 BORÅS
Report no / date -/-
Niklas Gunnarsson
Business area manager NIBE Stoves
Appendices
• Assembly and Installation Instructions
HAND ÖL
In accordance with standards below
marking was affixed:
European Standard:
SE Quality Certification, P-marked:
NO Standard NS 3059:
DK Standard:
DE and AT Standard DIN 18 891
and Art 15a B-VG:
Type:
Nominal Output:
Fuel:
Minimun draught:
Flue gas temerature:
Energy efficiency:
Emission of CO in cumbustion products:
Distance to cumbustible wall (mm):
Production number:
Follow the installation instructions.
Use only recomended fuels
NIBE AB Box 134 SE-285 23 MARKARYD AWEDEN
2006
EN 13240
Cert no 220316
SINTEF 043-xxx
xxxDS/EN 13240 plus
XX-91xxxx
H51/H52/H52T
5 kW
Wood
12 Pa
275°C
79%
0,13%
Behind 150
Beside 500
Corner 150
HAND ÖL
In accordance with standards below
marking was affixed:
European Standard:
SE Quality Certification, P-marked:
NO Standard NS 3059:
DK Standard:
DE and AT Standard DIN 18 891
and Art 15a B-VG:
Type:
Nominal Output:
Fuel:
Minimun draught:
Flue gas temerature:
Energy efficiency:
Emission of CO in cumbustion products:
Distance to cumbustible wall (mm):
Production number:
Follow the installation instructions.
Use only recomended fuels
NIBE AB Box 134 SE-285 23 MARKARYD AWEDEN
2006
EN 13240
Cert no 220316
SINTEF 043-xxx
xxxDS/EN 13240 plus
XX-91xxxx
H53/H54/H54T
5 kW
Wood
12 Pa
275°C
79%
0,13%
Behind 150
Beside 470
Corner 150
378
001
N
O
R
D
I
C
E
C
O
L
A
B
E
L
GB
51
TABLE OF CONTENTS
General 52
Installation distance to walls and ceiling 53
Removing the loose components 55
Supply of combustion air 57
Adjusting and connecting H51 58
Adjusting and connecting H52/H52T 59
Adjusting and connecting H53 61
Adjusting and connecting H54/H54T 62
Connection to the chimney 64
DEAR HANDÖL OWNER
We welcome you to the Handöl family and hope that you will
gain much pleasure from your stove. We understand that you
place high demands on both quality and design. As a new
owner of a stove from Handöl you have a stove with timeless
design and a long lifetime.
The stove combustion is also environmentally friendly and
efficient for the best heat production.
Read the installation instructions carefully before you begin
installation and the separate lighting and user instructions
before you light the fire.
WARNING!
The stove becomes very hot when lit
During operation, certain surfaces of the stove
become very hot and can cause burn injury if
touched. Be aware of the strong heat radiated
through the hatch glass. Placing flammable
material closer than the safe distance
indicated may cause a fire. Pyre lighting
can cause quick gas ignition with the risk of
damage to property and personal injury.
GB
52
General
This manual contains
instructions about how
the Handöl 50 series
must be assembled and
installed.
To guarantee the function and safety of the stove we
recommend that it is installed by a professional. Our Handöl
agents can recommend a suitable installer.
Instructions for lighting and use are also supplied with the
stove. Read them carefully and keep them safe for future use.
The stove is type approved and must be connected to a chimney
dimensioned for at least 350°C, the external connection
diameter is Ø150 mm. Supply air from the open air should be
used as combustion air.
Building application
Before installing a stove or erecting a chimney it is necessary
for you to apply for planning permission from your local
authority. Ask your local authority for advice regarding building
regulations and the application.
Structural support
Check that the wood joists are strong enough to bear the weight
of the stove and chimney. The stove and chimney can usually be
placed on a normal wooden joist in a single occupancy house if
the total weight does not exceed 400 kg.
Hearth plate
To protect the floor from any embers the stove must be placed
on a hearth plate. If the floor under the stove is flammable, it
must be protected by a non-flammable material which covers at
least 300 mm to the front and 100 mm on each side.
The hearth plate can consist of natural stone, concrete or 0.7
mm metal. As an accessory, the hearth plate is available in
painted steel.
Chimney
The stove requires a draft in the chimney of at least –12 Pa. The
draught is affected both by the length and area of the chimney,
and by how well sealed it is. Minimum recommended chimney
length is 3.5 m and a suitable cross section area is 150-200 cm²
(140-160 mm in diameter). Carefully check that the chimney is
sealed and that there is no leakage around soot hatches and flue
connections.
Note that a flue with sharp bends and horizontal routing reduces
the draught in the chimney. Maximum horizontal flue is 1 m,
on the condition that the vertical flue length is at least 5 m. It
must be possible to sweep the full length of the flue and the soot
hatches must be easily accessible.
Eldstadsbeklädnad
Löstagbart handtag
Rosterreglage
Asklåda
Förbränningsluftsreglage
Brasbegränsare
Typskylt
ANVISNING
51
52
52T
53
54
54T
50
ins talla tion s
Installationsanvisning 2
Installasjonsanvisning
5
Heizinstruktionen
8
Installationinstruction 11
Monteringsveiledning
14
Lämmity
17
Instructions
d’installation
20
Istruzioni
per
l’installazione
23
Installatievoorschriften 26
SE
NO
GB
DK
FI
IT
NL
DE
FR
eldnings
instruktion
H
50
Eldningsinstruktion 2
Heizinstruktionen 5
Fyringsinstruksjon 8
Fyringsvejledning 11
Istruzioniperl’accension e 14
Instructionsd’allumage 17
Stookinstructies 20
LightingInstructions 23
Lämmity 26
SE
DE
NO
DK
IT
FR
NL
GB
FI
HANDÖL
In accordance with standards below
marking was affixed:
European Standard:
SE Quality Certification, P-marked:
NO Standard NS 3059:
DK Standard:
DE and AT Standard DIN 18 891
and Art 15a B-VG:
Type:
Nominal Output:
Fuel:
Minimun draught:
Flue gas temerature:
Energy efficiency:
Emission of CO in cumbustion products:
Distance to cumbustible wall (mm):
Production number:
Follow the installation instructions.
Use only recomended fuels
NIBE AB Box 134 SE-285 23 MARKARYD AWEDEN
2006
EN 13240
Cert no 220316
SINTEF 043-xxx
xxxDS/EN 13240 plus
XX-91xxxx
H51/H52/H52T
5 kW
Wood
12 Pa
275°C
79%
0,13%
Behind 150
Beside 500
Corner 150
Technical data
Output 3-7 kW
Nominal output 5 kW
Efficiency level 79%
Model 51 52 52T 53 54 54T
Weight (kg) 128 135 172 143 149 190
Width (mm) 495 495 495 550 550 550
Depth (mm) 420 420 420 455 455 455
Height (mm) 825 825 875 825 825 875
The connection’s external diameter is Ø150 mm.
Type approved in accordance with:
European standard EN-13240
Swedish environmental and quality marking,
P-marking cert. no. 22 03 16
Norwegian standard NS 3059, Cert. No xxx-xxx
German standard DIN 18.891, XX-xx xx xxx
Fire-box surround
Grate shuttle
Ash-pan
Log guard
Air supply control
Removable handle
Type plate
GB
53
Installation distance to walls and ceiling
295
A 825
495
520
2000
Brännbart tak
420
135
D 20
B 705
C 65
Position the stove on a hearth plate and
check that the installation distances given
in the diagrams are met. The minimum
distance between the stove opening and
combustible parts of the building or décor
must be at least 1 m.
When top connecting a steel flue please
refer to the relevant manufacturer’s
installation instructions. Observe the safety
distances to combustible material that steel
flues require.
390
Brännbar vägg
150
840
735
280
Brännbar vägg
150
500
745
100
200
300
400
80
180
280
380
H51, H52 and H52T
*To prevent the discolouring of painted fire walls, we recommend a side distance the same as for the combustible wall.
290
Brandmur
50
700
635
180
Brandmur
50
140*
385*
A = height from floor to top flue connection, Ø150
B = height from floor to c /c smoke outlet rear
, Ø150
C = distance from back to
top flue (c/c), Ø64
D = distance from back to smoke outlet rear
, Ø150
280
Brännbar vägg
150
500
745
Tillåtet område för brännbart material
100
200
300
400
80
Combustible ceiling
Combustible wall
Fire-retardant wall of brick or concrete
Permit ted area fo r combus tible material.
Combustible wall
Fire-retardant wall of brick or concrete
Loading...