Hand Held Products IMAGETEAM 4400, IMAGETEAM 4700 User Manual
User’s Guide
User’s Guide
User’s Guide
User’s Guide
User’s Guide
User’s Gu ide
™
IMAGETEAM™ 4400/4700
2D Series
Hand Held Imager
User’s Guide
Statement of Agency Compliance
This device complies with part 15 of the FCC Rule s. Operation is subject to the
following two conditi ons: (1) this device may not cause harm ful interference, and
(2) this device must accep t any interference rec eived, including interfere nce that
may cause undesired operation.
FCC Class B Compliance State ment
This equipment h as been teste d and f ound t o comp ly with the li mits for a Class
B digital device p ursuant to par t 15 of the FCC Rules. These lim its are design ed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determ ined by turning the equip ment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving ante nna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio or television technician for
help.
Caution: Any changes or modifications made to this device that are not
expressly approved by Welch Allyn Data Collection, Inc. may void the user’s
authority to operate the equipment.
Note: To maintain compliance with FCC Rules and Regulations, cables
connected to this device must be
wire(s) have been grounded (tied) to the connector shell.
shielded
cables, in which the cable shield
Canadian Notice
This equipment does not exce ed the Class B limits for radio noise emissions as
described in th e Radio Interference Regula tions o f the Canad ian Departm ent of
Communications.
Le present appareil num erique n’emet pas de bruits radioelectriques depassant
les limites applicables aux app areils num eriques de la classe B pre scrites dans
le Reglement sur le brouillage radioelectrique edicte par le ministere des
Communications du Canada.
CDRH Laser Safety Statement
This product complies with US DHHS 21 CFR J Part 1040.10. This product is a
CLASS II LASER PRODUCT with a maximum output of 1.0 mW at 670
nanometers and continuous wave.
EN 60825-1 Laser Safety Statement
This product is classified as a CLASS 2 LASER PRODUCT with a maximum
output of 1.0 mW at 670 nanome ters per EN 608 25-1:1994 , Issue 2, June 1 997.
The CE mark on the product indicates that the system has be en tested
to and conforms with the provisions noted within the 89/336/EEC
Electromagnetic Compatibility Directive and the 73/23/EEC Low
Voltage Directive.
For further information please contact:
Welch Allyn Ltd.
Block 1, Bracken Business Park
Sandyford, C o. Dublin
Ireland
or
Welch Allyn Ltd.
1st Floor
Dallam Court Dallam Lane
Warrington, Cheshire WA2 7LT
England
Welch Allyn Data Collection, Inc. shall not be liable for use of our product with
equipment (i.e ., power supplies, p ersonal computers, et c.) that is not CE mar ked
and does not comply with the Low Voltage Directive.
Patents
The IMAGETEAM 4400/4700 products are covered by one or more of the
following U.S. P atents: 5,420,409 , 5,780,834, 5,723, 853; 5,723,868; 5,8 25,006;
5,900,613; 5,929,418. Other U.S. and foreign patents pending.
Scan on Demand is covered by the following patent: 5,463,214.
Image Sensor Containment System is covered by the following patent:
5,838,495.
Disclaimer
Welch Allyn Data Collection, Inc. reserves the right to make changes in
specifications and other information contained in this document without prior
notice, and the reader should in all cases consult Welch Allyn Data Collection,
Inc. to determine whether any such changes have been made. The information
in this publication does not represent a commitment on the part of Welch Allyn
Data Collection, Inc.
Welch Allyn Data Collection, Inc. shall not be liable for technical or editorial
errors or omissions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of this material.
This docume nt contains pr oprietary information wh ich is pro tected by copyr ight.
All rights are reserved. No part of this document may be photocopied,
reproduced , or translated into another language w ithout the prior written consent
of Welch Allyn Data Collection, Incorporated.
1999-2000 Welch Allyn Data Collection, Inc. All rights reserved.
Welch Allyn Data Collection, Inc. Web Address: http://dcd.welchallyn.com
Chapter 1 - Introduction and Installation
About the Hand-Held 2D Imager ......................................... 1-1
Unpacking the Imager....... ...................................... .............. 1-2
IT4400 Imager Identification................................................ 1-3
IT4700 Imager Identification................................................ 1-4
Laser and LED Safety........................................................... 1-5
Connecting the Scanner When Powered by Host
(Keyboard W edg e)......... ........................... ......................... 1-6
Reading Techniques.............................................................. 1-7
Depth of Field Charts.... ........................... ............................. 1-8
Chapter 2 - Programming
Introduction........................................................................... 2-1
Reset Factory Settings .......................................................... 2-2
Status Check ......... ................................................................ 2-2
All Symbologies ............................................................. ...... 2-3
Revision Selections... ....................................... ..................... 2-3
Terminal Interface ................................................................ 2-4
Supported Termin als Chart.................. ................ ................. 2-5
Keyboard Country ................................................................ 2-6
Keyboard Style ..................................................................... 2-7
Keyboard Modifiers.............................................................. 2-8
Keyboard Function Relationships......................................... 2-9
Connecting the Scanner to a Serial Port ............................. 2-10
Communication Settings..................................................... 2-11
Parity ............................................................................ 2-11
Baud Rate.................................................. ................... 2-12
Word Length Data Bits ........................................ ........ 2-13
Word Length St o p Bits... ............... ............................... 2-13
Hardware Flow Control................................................ 2-14
Software Flow Control................................................. 2-14
Serial Triggering .......................................................... 2-15
Power Saving Mode.. .... ...................................................... 2-16
Power Hold Mode. ........................... ........................... ........ 2-16
i
LED Power Level................................................................2-17
LED Flashing......................................................................2-17
Aimer Delay........................................................................2-18
Aimer Timeout....................................................................2-18
Aimer Interval.....................................................................2-19
AutoTrigger.........................................................................2-20
Scan Stand...........................................................................2-20
Scan Stand LE D In ten sity...... .......................................2-20
Scan Stand Lig hts....... ..................................................2-21
Presentation Mo de...............................................................2-21
Presentation Reread Delay......................... ...................2-21
Presentation Default .....................................................2-21
Presentation Aimer......... ..............................................2-22
Zoom ...................................................................................2-22
Zoom Placement........ ............... ....................................... ....2-23
Beeper Volum e.................. ...................................... ............2-24
Power Up Beeper ................................................................2-24
Output Sequence Beeper .....................................................2-24
Beep On Decode .................................................................2-25
Beeper Default................... .... ................ .......................2-25
Intercharacter, Interfunction,
and Intermessage Delays ..................................................2-26
Intercharacter Delay ......................... ...........................2-26
Interfunction Delay ......................................................2-27
Intermessage Delay ......................................................2-28
Prefix/Suffix Ov erview............ ........................... ................2-29
Adding a Prefix or Suffix .............................................2-30
Add a Carriage Return Suffix to All Symbologies ......2-31
Add a Code I.D. Prefix to All Symbologies ................2-31
Add an AIM I.D. Prefix to All Symbologies ...............2-31
Prefix Entries................................................................2-32
Suffix Entries.................. ........................... ...................2-32
Symbology Chart ................................................................2-33
Decimal to Hex to ASCII Conversion Chart.......................2-34
ii
Data Format Editor Overview.............................................2-35
Format Editor Commands.............................................2-36
Data Format Editor .......................................................2-38
Data Formatter..............................................................2-39
Require Data Format.....................................................2-39
Show Data Formats.......................................................2-39
Alternate Data Formats.................................................2-40
Output Sequence Overview.................................................2-41
Require Output Sequence .............................................2-43
Output Sequence Editor ................................................2-44
Multiple Symbols ................................................................2-45
No Read......... ...................................... ................................2-45
Print Weight ........................................................................2-46
Chapter 3 - Symbologies
Introduction ...........................................................................3-1
Codabar .................................................................................3-2
Start/Stop Characters ......................................................3-2
Message Len gth..... .... .... .... ... .... ................ .... ............... ...3 -2
Check Character..... ........................... .............................. 3-3
Code 39..................................................................................3-4
Start/Stop Characters ......................................................3-4
Message Len gth..... .... .... .... ... .... ................ .... ............... ...3 -4
Full ASCII..................................... ..................................3-5
Check Character..... ........................... .............................. 3-6
Interleaved 2 of 5...................................................................3-7
Message Len gth..... .... .... .... ... .... ................ .... ............... ...3 -7
Check Digit............ ....................................... ..................3-8
Iata 2 of 5...............................................................................3-9
Message Len gth..... .... .... .... ... ................ .... ............... .... ...3 -9
Code 93................................................................................3-10
Message Len gth..... .... .... .... ... ................ .... ............... .... .3-10
Code 128..............................................................................3-11
Message Len gth..... .... .... .... ... ................ .... ............... .... .3-11
ISBT ....................................................................................3-12
iii
EAN/JAN 8.........................................................................3-13
Check Digit............................ .......................................3-13
EAN/JAN 13.......................................................................3-14
Check Digit............................ .......................................3-14
EAN Addenda.....................................................................3-15
UPC A...................................... ...........................................3-16
Check Digit............................ .......................................3-16
Number System ............................................................3-16
UPC E0....... ............................................................. ............3-17
Check Digit............................ .......................................3-17
Number System ............................................................3-17
Version E Expand.........................................................3-18
UPC E1....... ............................................................. ............3-18
UPC Addenda......................................................................3- 18
RSS-14 ................................................................................3-19
RSS-14 Limited....................................................... ............3-19
RSS-14 Expanded ................. ...................................... ........3-20
Message Len gth.......... .... ... .... .... ................ ............... ....3-20
Codablock ...........................................................................3-21
Message Len gth.......... .... ... .... .... ................ ............... ....3-21
PDF417 ...............................................................................3-22
Message Len gth.......... .... ... .... .... ................ ............... ....3-22
Micro PDF417.....................................................................3-23
Message Len gth.......... .... ... .... .... ................ ............... ....3-23
Code 49 ...............................................................................3-24
Message Len gth.......... .... ... .... .... ................ ............... ....3-24
Composite Codes ................................................................3-25
Message Len gth.......... .... ... .... .... ................ ............... ....3-25
U.S. Postal Service POSTNET Code..................................3-26
Planet Code.........................................................................3-26
British Post Office 4 State Code ........................................3-26
Canadian 4 State Code ........................................................3-26
Dutch Postal Code...............................................................3-26
Australian 4 State Code.......................................................3-27
Japanese Postal Service.......................................................3-27
QR Code................ ..............................................................3-28
Message Len gth.......... .... ... .... .... ................ ............... ....3-28
iv
Data Matrix..........................................................................3-29
Message Len gth..... .... .... .... ... .... ................ .... ............... .3-29
MaxiCode ............................................................................3-30
Message Len gth..... .... .... .... ... .... ................ .... ............... .3-30
Structured Carrier Message Only .................................3-31
Aztec Code ..........................................................................3-32
Message Len gth..... .... .... .... ... .... ................ .... ............... .3-32
VeriCode .............................................................................3-33
VeriCode Size...............................................................3-34
Test Menu........................................................ ....................3-35
2D Scan Diagnostics ............ .... ... .... .... ................ ... .............3- 35
Chapter 4 - OCR P r ogramming
Introduction ...........................................................................4-1
OCR.......................................................................................4-2
Creating OCR Templates ......................................................4-3
Creating an OCR Template.............................................4-3
Stringing Together Multiple Formats
(Creating “Or” Statements).............................................4-5
Creating a User-Defined Variable ..................................4-6
Adding an OCR Chec k Character. ..................................4-6
OCR Template Codes .....................................................4-7
Chapter 5 - Default Charts
Communication (RS-232) Selections .............................5-1
Imager Selectio ns.................. ........................... ...............5 -1
Prefix/Suffix Selections ........... ........................... ...........5 -2
Data Formatter Selections...............................................5-2
Output Sequence Selections............................................5-2
Linear Symbologies........................................................5-3
Postal Symbology Selections..........................................5-5
2D Matrix Selections .................... .... .... .... .... ... .... .... .... ...5 -5
v
Chapter 6 - Quick*View
Quick*View Demonstration Software Instructions ..............6-1
Setting Up the Imager and the Quick*View Software...6-1
Installing Quick *View from the Web................. ..................6-2
Using the Quick* View Sof tware ................................ ..........6 -3
Electronic Parts Manufacturing Demonstration .............6-6
Patient Registration Demonstration................................6-8
Bills of Lading Demonstration .......................................6-9
Load New Imager Software..........................................6-14
Serial Programming Commands...................................6-15
Status Check ..........................................................6-17
Output Selections ..................................................6-17
Communication Settings .......................................6-18
Imager Selectio ns ........................... .......................6-19
Output Selections ..................................................6-20
Prefix/Suffix Se lectio ns ................. ............... ........6-20
Data Formatter Selections .....................................6-21
Output Sequence Selections ..................................6-21
Linear Symbology Selections ...............................6-21
Stacked Symbology Selections .............................6-25
Postal Symbology Selections ................................6-25
2D Matrix Symbology Selections ...... ...................6-26
Chapter 7 - Visual Menu
Visual Menu Introduction.....................................................7-1
Installing Visual Menu fr om the Web.......... ................ ..7-2
Chapter 8 - Interface Keys
Chapter 9 - Product Specifications & Pinouts
Product Specifications.......................... .................................9-1
Cable Pinouts ........................................................................9-3
RS-232 Output, external power (IT4400 and IT4700)...9-3
IT4400 Dimensions...............................................................9 -4
IT4700 Dimensions...............................................................9 -5
vi
Chapter 10 - Maintenance & Troubleshooting
Repairs.................................................................................10-1
Maintenance ........................................................................10-1
Replacing the Interface Cable.......................................10-2
Troubleshooting...................................................................10-4
Application Support......................................................10-5
Chapter 11 - Customer Support
Obtaining Factory Service...................................................11-1
Limited Warranty ................................................................11-3
Sample Symbols
Programming Chart
vii
viii
1
Introduction an d In sta llation
About the Hand - He ld 2D Imager
The hand-held 2D Imager is an economical, durable solution for a wide variety
of data collection appl ications. The Imager features the following:
• A tough, ergonomic thermoplastic housing for comfort and durability.
• Omni-directional reading of a variety of printed symbols, including the
most popular linear and 2D matrix symbologi es.
• Advanced binary optics for ease of aiming and framing labels.
• RS-232, keyboard wedge, and laser emulation communication outputs.
• The ability to captur e and do wnload image s to a PC for signatu re captur e
software applications, and PC-based decoding.
• The ability to read single line OCR-A and OCR-B fonts.
About this Manual
This user’s guide p rovides installation instr uctions for the hand-held Image r. The
chapters contain the following information:
Chapter 1 Unpacking and installing the Imager
Chapter 2 Programming selections
Chapter 3 Symbology programming selection s
Chapter 4 OCR programming
Chapter 5 Default settings
Chapter 6 Quick*View software infor mation and serial program ming
commands
Chapter 7 Visual Menu softwar e
Chapter 8 Interface Keys
Chapter 9 Product specification s and conne ctor pi nout li stings
Chapter 10 Maintenance and troub leshooting
Chapter 11 Customer support, service information, and warranty
1 - 1
Unpacking the Imager
Open the carton. The shipping carton or container should contain:
IMAGETEAM 4400:
IMAGETEAM 4400
Hand Held Imager
Holder
Universal Power Supply
and Power Cable
IMAGETEAM 4700:
IMAGETEAM 4700
Hand Held/Fixed
Mount Imager
Quick*View
Visual Menu
User’s Guide
Demonstration
Diskettes
Demonstration
Diskettes
User’s Guide
Universal Power Supply
and Power Cable
• Check to make sure everything you ordered is present.
• Save the shipping container for later storage or shipping.
• Check for damage during shipment. Report damage immediately to the
carrier who delivered the carton.
1 - 2
IT4400 Imager Ide ntifi cation
Enlarged View of Label
Model# = 4400XX-XX
Manufactured = July 1999
Seria l # = P-12- 34567
S/W = 34567001/4400
Hand Held IT4 400 I mag er
Bottom View
1 - 3
IT4700 Imager Ide ntifi cation
Enlarged View of Label
Hand Held IT4700 Imager
Bottom View
1 - 4
Laser and LED Safety
The Laser A iming subsystem p rojects 670 nm laser light onto the bar code target
to define the optical field of view. The projected pattern consists of a central
cross and four 90 de gree corner sections. T his pattern is gener ated by a lens and
diffractive component positioned at the output of the enclosed laser diode. This
projected pattern assists the operator to frame the bar code being scanned.
The Good Read Indicator and the LED Illumination Array have been tested in
accordance with the spe ci ficati on “Safety of Laser Products” EN 60825-1:1994,
Issue 2, June 1997 and found to satisfy the requirements of Class 1. Class 1
optical systems are consi dered safe under r easonably foreseeab le cond itions of
operation. The Aiming Laser has been tested in accordance with the
specification “Safety of Laser Products” EN 60825-1:1994, Issue 2, June 1997
and found to satisfy the requirements of Class 2. Class 2 systems are
considered to emit visible radiation in the wavelen gth range from 400 nm to 700
nm. Eye protection is normally afforded by aversion responses including the
blink reflex. It is recommended that you do not stare into the beam or cause
others to stare into the beam.
1 - 5
Connecting the Scanner When Powered by Host
(Keyboard Wedge)
A scanner can be connected between the keyboard and PC as a “keyboard
wedge,” plug ged into the s erial p ort, or conn ected to a por table data terminal in
wand emulation or non decoded output mode.
Note: Only un its ordered from the factory with keyboar d wedge capability can be
connected as keyboard wedge units.
The following is an example of a keyboard wedge connection:
1. Turn off power to the terminal/computer.
2. Disconnect the keyboard cable from
the back of the terminal/computer.
Disconnect
3. Connect the appropriate interface cable to
the scanner and to the
terminal/
computer. The scanner will beep twice.
4. Turn the terminal/computer power back on.
5. Verify the scanner
operation by scanni ng
a bar code from the
back cover of this
manual. The scanner
will beep once.
The scanner is now connected and read y to communicate with your terminal/PC.
You must program the scanne r for your inter face befor e bar code data can be
transmitted to your terminal/PC. If you are using the scanner as a keyboard
wedge, see"Terminal Interface" on page 2-4. If the scanner is connected via a
serial port, turn to "Connecting the Scanner to a Serial Port" on page 2-10.
1
3
2
4
1 - 6
Reading Techniques
The hand-held Ima ger has a view finder (shown be low) wh ich is similar to those
on cameras. The view finder allows you to position the code within the field of
view.
The illustration below shows where to aim the red illuminated beam over the
symbol for a good read. Center the symbology in the view finder. The entire
symbology must be within the view finder (aiming beam). The view finder
changes size as you move the Imager closer to or farther away from a code.
Linear bar code 2D Matrix symbol
Note: The symbols can be in any orientation for the Imager to read.
The view finder is smaller when the Imager is closer to the code and larger when
it is farther from the code. Symbologies with smaller bars or elements (mil size)
should be read closer to the unit. Symbologies with la rger bars or elements (m il
size) should be read f arthe r from th e unit. (see "Depth of Field Charts "on page
1-8.) To read single or multiple symbols (on a page or on an object), hold the
Imager at an appropr iate distance fro m the target, pull the trigger , and center the
view finder cross hairs on the symbol.
View Finder
(Aiming Beam)
1 - 7
Depth of Field Charts
Depth of Fiel d for High Densi ty Imager (2" No mina l Focus)
Code Size Near Distance Far Distance
QR 6.6 mil (0.017 cm) 1.7 inches (4.3 cm) 2.4 inches (6.1 cm)
Data Matrix 6.6 mil (0.017 cm) 1.7 inches (4.3 cm) 2.4 inches (6.1 cm)
Linear 4 mil (0.01 cm) 1.6 inches (4.1 cm) 2.5 inches (6.4 cm)
OCR 6 pt. (20 cpi) 2 inches (5.1 cm) 3.5 inches (8.9 cm )
Depth of Field for High Density10 Imager (3" Nominal Focus)
Code Size Near Distance Far Distance
QR 10 mil (0.025 cm) 2.0 inches (5.1 cm) 4.0 inches (10.2 cm)
Data Matrix 10 mil (0.025 cm) 2.0 inches (5.1 cm) 3.5 inches (8.9 cm)
Linear 5 mil (0.013 cm) 2.75 inches (7.0 cm) 3.75 inches (9.5 cm)
OCR 12 pt. (12 cpi) 2 inches (5.1 cm) 5 inches (12.7 cm)
Depth of Fiel d for Long Range Imager (5" Nominal Focus)
Code Size Near Distance Far Distance
Linear 7.5 mil (0.019 cm) 3.0 inches (7.6 cm) 5.0 inches (12.7 cm)
Linear 10 mil (0.025 cm) 2.5 inches (6.4 cm) 4.75 inches (12.1 cm)
Linear 15 mil (0.038 cm) 2.0 inches (5.1 cm) 7.5 inches (19.1 cm)
Data Matrix 15 mil (0.038 cm) 2.5 inches (6.4 cm) 4.0 inches (10.2 cm)
Aztec or QR 15 mil (0.038 cm) 3.5 inches (8.9 cm) 5.0 inches (12.7 cm)
Maxicode 35 mil (0.089 cm) 2.0 inches (5.1 cm) 9.0 inches (22.9 cm)
1 - 8
2
Programming
Introduction
Use this section to progra m the hand-held Imager.
This programming section contains the following menuing selections:
• General Sel ections
• Terminal Interface Selections
• Keyboard Selections
• Communication Set tings
• Imager Selection s
• Output Selections
• Prefix/Suffix Selections
• Data Formatter Selections
• Output Sequence Selections
2 - 1
Reset Factory Settings
All operating parameters are stored in nonvolatile memory resident in the
Imager, wher e they are permanently retai ned in the event of a power inte rruption.
When you receive you r Imager, certa in operating param eters have already b een
set. These are the factory defaults, indicated by the symbol “✱” on the
programming menu pages (beneath the default program ming symbo l). Default
charts begin on page 5-1.
Depending on yo ur model, sca n one of the fo llowing ba r codes to set th e imag er
to the o riginal factory settings, cle aring any p rogramming changes you may have
made.
HD
LR
HD10
Status Check
Read the Show S oftware Re vision symbol to tran smit the soft ware revisi on level
to the host terminal. The software revision will be printed out as
“REV_SW:$ProjectRevision: 1.xx$;REV _WA:31204734-xxx.”
Read the Show Data Formats symbol to transmit t he existing D ata Format Edito r
formats. One format per line will be printed out.
Show Software
Revision
2 - 2
Show Data Formats
All Symbologies
If you want to decode all the symbologies allowable for your scanner, scan the
All Symbologies On code.
All Symbologies
On
All Symbologies
Off
Revision Select i ons
Both the following pro gramming codes would not nor mally be needed unless you
have a problem with the unit. An Application Support Representative may
request the boot code or power P C revision information in orde r to trouble shoot
a problem.
Boot Code RevisionPower PC Revision
2 - 3
Terminal Interface
IMAGETEAM 44 00 and 4700 scann ers are factory progr amm ed for a keyboar d
wedge interface to an IBM PC AT with a USA keyboard. If this is your interface
and you do not need to modify the settings, skip to page 2-16 for Imager
Selections.
If your interface is not a standard PC AT, refer to the "Supported Terminals
Chart" on page 2-5 and locate the Terminal ID number for your PC. Scan the
Terminal ID bar code below, then scan the numeric bar code(s) on the inside
back cover of this manual to program the scanner for your terminal ID. Scan
Save to save your selection.
For example, an IBM PS/2 terminal has a Terminal ID of 002. You would scan
the Ter minal ID bar code, then 0, 0, 2 from the inside back cover, then Save. If
you m ake an error wh ile scanning the digits (before scanning Save), scan the
Discard code on the back cover and scan the digits and the Save code again.
Factory Default = 03
Terminal ID
Save
2 - 4
Supported Terminals Chart
Terminal Model(s)
Terminal
DEC PC433 SE (Portable PC) 003
DELL Latitude (Portable PC) 003
DTK 486 SLC (Portable PC) 003
Fujitsu Stylistic (Portable PC) 003
HHLC (Code 128 Emulation)
089
IBM PC X 001
IBM PS/2 25, 30, 77DX2 002
IBM
IBM
IBM
IBM
AT, PS/2 30-286, 50, 55SX, 60, 70, 003,
70-061, 70-121, 80
AT Compatibles Keyboard Emulation
(Non-wedge)
Thinkpad 360 CSE, 34, 750
(P ortable PC)
Thinkpad 365 , 755 CV
(P ortable PC)
003
097
003
IBM AT Thinkpad 106
Midwest Micro Elite TS 30 PS (Portable PC) 003
Mitak 4022 (Portable PC) 003
Olivetti M19, M24, M28, M200 001
I.D.
*
Olivetti M240, M250, M290, M380, P500 003
Reliasys TR 175 003
RS-232 TTL 000
Televideo 990, 995, 9060 002
Texas Instruments Extensa 560CD (Portable PC) 003
Toshiba 2600 (Portable PC) 003
Toshiba Satellite T1960, T2130, CS (Portable PC) 003
Zenith Z-note (Portable PC) 003
* This capability is not available for the IT4700. Contact the factory if this capability is
needed for the IT4700.
Note: These interfaces are available only for units that have 1 megabyte of
program me mory. The software revision indicate s the memory s ize. If you
are not certain of your unit’s memory, please contact Welch Allyn’s
Application Support (see page 10-5).
2 - 5
Keyboard Country
Scan the Program Keyboard Country bar code below, then scan the numeric
bar code(s) from the inside back cover, then the Save bar code to program the
keyboard for your country. As a general rule, the following characters are not
supported by the scanner for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
Keyboard Country
Country Code Scan Country Code Sc an
Belgium.....................1 Italy........................5
Denmark...................8 Norway...................9
Finland......................2 Spain......................10
France ......................3 Switzerland............6
Germany/Austria....... 4 USA
Great Britain .............7
(Default)
.........0
2 - 6
Save
Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock.
Default =
Regular.
Regular
Caps Lock
Shift Loc k
to U.S. keyboards.)
Automa tic Caps Lo ck
software tracks and r eflects if you have Caps Lock on or of f (AT and PS/2 only).
This selection can only be used with systems that have an LED which notes the
Caps Lock status.
Emulate E xte rnal Keyb oa rd
keyboard (IBM AT or equivalen t), but sh ould not be use d for laptops. To connect
the scanner to a laptop, use "Automatic Direct Connect Mode On"on page 2-8.
is used when you normally have the Caps Lock key off.
is used when you normally have the Caps Lock key on.
is used when you normall y have the Shift Lock key on. ( Not common
is used if you cha nge the Caps Lo ck key on and off. T he
should be scanned if you do no t have an exter nal
* Regular Caps Lock
Shift Lock
Automatic
Caps Lock
Emulate External
Keyboard
2 - 7
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ A SCII codes and Turbo
Mode.
Control + ASCII Mode On
control characters for values 00-1F. Refer to "Keyboard Function
Relationship s" on page 2-9 for CTRL+ ASCII Values.
Control + ASCII
Mode On
Turbo Mode
use with IB M AT onl y.) If th e terminal drops character s, do not u se Turbo M ode.
- The scanner send s character s to an IB M AT term inal faster. (Fo r
- The scanner sends key combinations for ASCII
Default = Off
* Control + ASCII
Mode Off
Default = Off
Turbo Mode On
Numeric Keyp ad Mod e
numeric keypad.
Default = Off
- Sends numeric characters as if entered from a
* Turbo Mode Off
Numeric Keypad
Mode On
Automatic D ir ect Conn ect
keyboard is disabled when you plug in the scanner. This selection can also be
used if you h ave an IBM AT style terminal a nd the system is drop ping characters.
Default = Off
Automatic Direct
Connect Mode On
2 - 8
* Numeric
Keypad Mode Off
- Use this selection if you are using a laptop whose
* Automatic Direct
Connect Mode Off
Keyboard Func tion Re lationships
The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII
“CTRL”+ relationships apply to all terminals that can be used with the scanner.
Function Code HEX/ASCII Value Full ASCII “CTRL” +
NUL 00 2
SOH 01 A
STX 02 B
ETX 03 C
EOT 04 D
ENQ 05 E
ACK 06 F
BEL 07 G
BS 08 H
HT 09 I
LF 0A J
VT 0B K
FF 0C L
CR 0D M
SO 0E N
SI 0F O
DLE 10 P
DC1 11 Q
DC2 12 R
DC3 13 S
DC4 14 T
NAK 15 U
SYN 16 V
ETB 17 W
CAN 18 X
EM 19 Y
SUB 1A Z
ESC 1B [
FS 1C \
GS 1D ]
RS 1E 6
US 1F -
2 - 9
Connecting the Scanner to a Serial Port
6. Turn off power to the terminal/computer.
7. Connect the interface cable to the scanner.
8. Connect the interface cable to the 5 or 14 VDC power supply and plug in the
power supply. The scanner will beep twice.
9. Connect the interface cable to the terminal/computer.
Power Supply
1
10. Turn the terminal/computer power back on.
11. Verify the scanner operation by scanning a bar code from the back cover of
this manual. The scanner will beep once.
The scanner is now connected and read y to communicate with your terminal/PC.
Turn to "Communication Settings" on page 2-11 to program the communication
parameters for a serial inter face.
2
3
Interface Cable
2 - 10
Loading...