Page 1
AA Lithium Batteries
required. Use of other
types of batteries, such as
alkaline, will significantly
decrease battery life.
2x
HES K100 Aperio Series
Wireless Cabinet Lock
Installation and Operating Instructions
Products Specifications
Wireless Frequency: 2.4GHz, IEEE 802.15.4, using AES 128-bit encryption
Lock Battery Type: AA Lithium, 1.5 Volts (V)
Battery Life: 50,000 cycles*
*All battery life claims are approximate and based on a set configuration profile. Battery performance is based on pre-defined system settings such
as battery chemistry and battery model used, credential presentation settings (LED/buzzer), UHF polling period, UHF status intervals, and
operations per day. Actual battery performance will vary and depends on the factors above.
Operating Temperature: 32 to 122 F (0 to 50 C)
HID® multiCLASS SE® technology Credentials Supported:
High Frequency (13.56 MHz):
HID iCLASS®
HID iCLASS SE® (SIO-enabled)
HID iCLASS® Seos™
HID MIFARE® SE
HID DESfire® EV1 SE
MIFARE CLASSIC
DESfire® EV1
Low Frequency (125 kHz):
HID Prox®, AWID, EM4102, ioProx
NFC/BLE-enabled Mobile Phones
Page 1 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 2
Door
Thickness
Reader
Mounting
Cut to
approx.
screw
length
Lock
Mounting
Cut to
Approx.
Screw
Length
1/16”
Coupling Nut
and 3” Rod
10/16”
8-32 x 1-3/4”
Break Away
1-1/16”
1/4"
Coupling Nut
and 3” Rod
13/16”
8-32 x 1-3/4”
Break Away
1-1/4”
1/2”
Coupling Nut
and 3” Rod
1-1/16”
8-32 x 1-3/4”
Break Away
1-7/16”
3/4”
Coupling Nut
and 3” Rod
1-5/16”
8-32 x 1-3/4”
Break Away
No Cut
1”
Coupling Nut
and 3” Rod
1-9/16”
8-32 x 2-1/2”
2”
1-1/4”
Coupling Nut
and 3” Rod
1-13/16”
8-32 x 2-1/2”
No Cut
1-1/2”
Coupling Nut
and 3” Rod
2-1/16”
8-32 x 2-3/4”
No Cut
Door Thickness
Shaft Used
1/16” – 1/2”
L1
>1/2” – 1½”
L2
>1½” – 2¼”
L3
Recommended Tools
Flathead Drivers — 3/32”, 3/16”
Drill, Drill Bits — 1/16”, 3/16”, 1/2”
Phillips Drivers — P0, P2
Pencil, Wire Stripper, Level, Square, Ruler, Punch, Scissors
Hardware Specifications
Table 1 – Shaft Length
Table 2 – Mounting Screw Length for Various Door Thickness
Page 2 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
For Technical Support Please call 1-800-810-WIRE
Page 3
6 X 1/2"
6x
(D)
6-32 X 5/16”
3x
(C)
8-32 X 5/16”
(B)
2-56 X 7/16”
2x
(A)
Reader
Lock Body
Strike Plate
Installation
Template
Mechanical Key Override
Hardware
8-32 X 2-1/2”
2x
(G)
8-32 X 2-3/4”
2x
(E)
8-32 X 1-3/4”
2x
(F)
Lithium Batteries
2x
Double Door
Bracket
8-32 X 3” Rod
(H)
8-32 Nut
(J)
Threadlock
Package Contents
Page 3 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 4
1. Separate Strike Plate Template.
2. Establish centerline (for double door
cabinet prep go to page 6).
Orientation A
Orientation B
Orientation C
Lock Orientation Options
Prepping the Cabinet/Drawer Face
Page 4 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 5
3. Measure cabinet wall thickness and mark
offset line on face of cabinet/drawer. The
offset line should match with the interior
edge of the cabinet wall.
4. Continue centerline to face of
cabinet/drawer
5. Align template to offset line and
centerline. Remove backing and apply
template onto cabinet/drawer face.
6. Use punch to mark drilling
locations then drill mounting holes. If
using mechanical key override, drill
key override hole as well.
Center
Offset Line
line
Page 5 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 6
3. Align offset line on template to the edge of the stationary door and align center
line with the established center line above. Remove backing and apply template to
cabinet face. Continue with Step 6 in previous section.
1. Establish center line on inside
of stationary door.
2. Continue center line onto
outside face of cabinet.
Prepping the Cabinet/Drawer Face (Double Door)
Page 6 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 7
1. Align reader with mounting holes and pull
cable through as shown. Trim Threaded rod
to length as outlined in table 2.
2. Add Threadlock to threaded rod.
Secure Reader to cabinet/drawer using
the cut threaded rod and coupling nut.
DO NOT overtighten.
1. Slide Override into slot as shown.
2. Ensure that override retracts latch
bolt before installation. Override
should rest loosely until lock body and
battery cover are installed.
Reader Installation
Mechanical Override (Optional)
Page 7 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 8
1. Insert reader cable through hole
in back of lock body.
2. Align lock body to mounting holes
andsecure to cabinet/drawer face using
2x screw F and 2x screw D. If thick
cabinet/drawer then use 2x screw E or
2x screw G instead of 2x screw F. DO
NOT over tighten.
3. Plug cable into slot on lock body.
4. Tuck excess cable into lock body
cavity as shown.
5. Any excess cable should be inserted
into the cavity as shown below.
6. For cabinet/drawer face thicker
than1/2”, add a third screw D as
shown.
Lock Body Installation
Page 8 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 9
1. Install AA lithium batteries in appropriate
position.
2. Install cover and secure using 2x
screw A.
Mechanical key override cam lock sold
separately.
1. Insert cam lock through the outside
of the cabinet/drawer face and secure
with locking nut. Insert the end of Cam
into the mechanical override and secure
with nut as shown.
Important Note – Reader MUST be programmed before installing the strike plate. If the cabinet
is closed before the reader is programmed and after the strike plate is installed, you will be locked out of
the cabinet.
Installing the Batteries
Mechanical Key Override (Optional)
Page 9 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 10
1. Align strike plate template to centerline
and edge of cabinet. Drill mounting holes.
2. Secure strike plate to inside cabinet
wall using 2x screw D, but do not fully
tighten. Adjust strike plate so the edge
is flush with the cabinet wall edge then
tighten.
3. After the strike plate is in the desired position, fasten screw D into strike plate as
shown below.
Strike Plate Installation
Page 10 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 11
1. Align Double door bracket with mounting holes from the strike plate template.
Secure double door bracket using 3x screw D.
Double Door Strike Installation
2. Secure strike plate to double door bracket using 3x screw D as shown below.
Page 11 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 12
LED Codes
Page 12 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 13
Technical Data – AH20
Approvals
CE, ETL, FCC, IC, C-Tick
Safety and emissions
FCC 47CFR Part 15 subpart
B and subpart C; IC RSS-210
EN ETSI 301 489-17 v2.1.1;
ENETSI 300 328 v1.7.1;
EN 60950-1 ed.2 2007
Dimensions
82x82x37
Power Supply
8-24 VDC
Current
250 mA minimum
Internal Antenna
2cross polarized dipoles
External Antenna
(Part No. EXT-10-ANT)
One reverse polarity SMA
external antenna connector.
Optional antenna type dipole with max
antenna gain of 3.9dBi
Radio Standard
IEEE 802.15.4(2.4GHz) –
15 channels (11-25)
Encryption (Radio
Communications)
AES 128 bits
Wireless Operating Range
Up to 50 ft
Receiver Sensitivity
100dBm 20%PER
Wireless Transmit Power
10 dBm/MHz
Class of Protection
IP 20
Operating temperature range
5°C to 35°C
Humidity
< 95% non-condensing
Status
LED (red/green/orange)
Aperio Hub
Page 13 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 14
Connect the Wiegand D1, D0, red, and green LED signals.
For Emergency Power & Local (Hard
Wired) Firmware Updates, use micro
USB port located on the side of the K100
Connecting the Hub
The following applies only to Aperio factory paired kits with AH20 Hubs.
Note: The Green LED input is used to grant access to the cabinet lock. If the Green LED
signal is not available to indicate approved access, the approval input can be
activated by a relay with “NO” attached to Green LED and “C” to GND.
The Red LED input is used to indicate access denied. If the RED LED signal is
not connected, the lock will flash RED three times when a non-approved card is
presented indicating loss of connection to the hub rather than access denied. Any
other codes may be reference on the LED reference card.
Micro USB Port
Page 14 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 15
FCC Statement
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Operation with non-approved equipment is likely to result in interference to radio and TV reception. The user is
cautioned that changes and modifications made to the equipment without the approval of manufacturer could void
the user’s authority to operate this equipment.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation.
To comply with FCC and Industry Canada RF radiation exposure limits for general population, the module must
be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
This module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification
Number are not visible when the module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the enclosed module. In that case, the final
end product must be labeled in a visible area with the following:
Contains FCC ID: VC3-R100V3
Contains IC: 7160A-R100V3
IC Statement
This device complies with Industry Canada license-exempt RSS standards(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation.
Conformité aux normes FCC
Cet équipement a été testé et trouvé conforme aux limites pour un dispositif numérique de classe B,
conformément à la Partie 15 des règlements de la FCC. Ces limites sont conçues pour fournir une protection
raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement génère, utilise
et peut émettre des fréquences radio et, s'il n'est pas installé et utilisé conformément ment aux instructions du
Page 15 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 16
fabricant, peut causer des interferences nuisibles aux communications radio. Rien ne garantit cependant que
l'interférence ne se produira pas dans une installation particulière. Si cet équipement provoque des interférences
nuisibles à la réception radio ou de télévision, qui peut être déterminé en comparant et en l'éteignant, l'utilisateur
est encouragé à essayer de corriger les interférence par une ou plusieurs des mesures suivantes:
1. Réorienter ou déplacer l'antenne de réception.
2. Augmenter la distance entre l'équipement et le récepteur.
3. Branchez l'appareil dans une prise sur un circuit différent de celui auquel le récepteur est connecté.
4. Consultez votre revendeur ou un technicien radio / TV pour assistance.Avertissement
Les changements ou modififications à cet appareil sans expressément approuvée par la partie responsable de
conformité pourraient annuler l'autorité de l'utilisateur de faire fonctionner cet équipement.
L'opération est soumise aux deux conditions suivantes:
(1) Cet appareil ne doit pas causer d'interférences nuisibles, et
(2) Cet appareil doit accepter toute interférence reçue, y compris les interférences susceptibles de provoquer un
fonctionnement indésirable.
Pour se conformer aux limites d'exposition aux rayonnements RF de la FCC et d'Industrie Canada pour la
population en général, le module doit être installé pour fournir une distance de séparation d'au moins 20 cm de
toutes les personnes et ne doit pas être localisé ou en combinaison avec une autre antenne ou émetteur.
Ce module est étiqueté avec son ID FCC et son numéro de certification IC. Si l'identifiant FCC et le numéro de
certification IC ne sont pas visibles lorsque le module est installé à l'intérieur d'un autre appareil, l'extérieur de
l'appareil dans lequel le module est installé doit également afficher une étiquette faisant référence au module cijoint. Dans ce cas, le produit final final doit être étiqueté dans une zone visible avec ce qui suit:
Contient FCC ID: VC3-R100V3
Contient IC ID:7160A-R100V3
Conformité aux normes IC
Cet appareil est confrome avec Industrie Canada exempt de license RSS standard(s).
Son fonctionnement est souimes aux deux conditions suivantes:
(1) cet appareil ne peut causer d’interférences, et
(2) cet appareil doit accepter toute interference, y compris des interférences qui peuvent provoquer un
fonctionnement indésirable du périphérique.
Page 16 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Page 17
Page 17 of 17 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Loading...