KS100-640 Aperio
Cabinet Lock Series
Installation Instructions
HES, Inc.
Phoenix, AZ
1.800.626.7590
www.hesinnovations.com
Package Contents
Recommended Tools
Approved RFID Credential
Phillips P2 driver, RJ45 cable
PoE power injector (48VDC)
Optional Additional Tools:
Gang box to mount hub
SFIC Core for key override
Optional Additional Tools:
Normally Open DPS switches
Product Specifications
Wireless Frequency: 2.4 GHz, IEEE 802.15.4, using AES 128bit encryption
Hub Power Requirement: 8-24VDC, 250mA
Lock Power: 48VDC Power over Ethernet (PoE) 802.3af compliant
Operating Temperature: -10C to 50C
Holding Force: 250 lbs
FCC Part 15, Compliant, Industry Canada Compliant
BHMA: A156.3, A156.36, A156.25 Compliant
Credentials Supported: 125kHz Proximity or 13.56MHz iCLASS, iCLASS SEOS, iCLASS SE, ISO1443B UID, Mifare, Mifare Plus,
Desfire SE, Desfire EV1, and NFC credentials are supported depending on lock model.
For technical support please call 1-800-626-7590
Handling
Selector
Lock
Handle
Mounting
Plate
Mounting Screws
Cams (x3)
DPS Cable
SFIC
Cam
Part Number 3080006.008 Rev. A ©2013, HES, Inc. 1
System Overview
The KS100-640 wireless server cabinet lock extends access control to a server cabinet
without the complexity and expense of running wires. The KS100-640 cabinet lock connects
to an access control system through the included communication hub. The communication
hub connects to the access control system with Wiegand wiring typical of a Wiegand reader.
When a credential card is presented to the reader on the lock, the request for access is
sent wirelessly to the communication hub. The communication hub then communicates
through Wiegand wiring to the access control system where the decision is made to grant or
deny access.
Installation Steps
B. Prepare the Cabinet
C. Install the Lock
D. Install Handing Selector
A. Install an SFIC Core
Part Number 3080006.008 Rev. A ©2013, HES, Inc. 2
1. Installing an SFIC Core
A key override (SFIC) provides a backup entry method in the rare case the KS100 or access
control system is inactive. We recommend this option.
The included SFIC cam has been tested with Medeco and Sargent 6- or 7-pin SFIC cores.
2. Prepare the Rack
Locate the 25mm x 150mm lock cutout on the
door, some doors may require modification.
1. Verify 48V POE power is available at the
rack.
2. Re-use the existing cam if possible.
3. Three cams are supplied.
CAM
CAM LENGTH
CAM DEPTH
CAM 1
38mm [1-1/2"]
16mm [5/8"]
CAM 2
38mm [1-1/2"]
24mm [15/16"]
CAM 3
45mm [1-3/4"]
22.5mm [7/8"]
1. Remove plug from handle
3. Insert SFIC into lock
7-pin
2. Insert cam into SFIC
Use the included spacers
with 6-pin SFICs.
6-pin
Part Number 3080006.008 Rev. A ©2013, HES, Inc. 3
3. Installing the lock on the door
1. Slide lock into cutout.
2. Plug 48V PoE RJ-45
cable into lock. Lock will
beep once and perform
self test.
3. Optional: The DPS signal is closed when the handle is
resting in its locked position. The DPS circuit can be
extended to include normally open DPS switches arranged
in a series to monitor additional doors and panels.
4. Attach rear bracket with
screws.
DPS Extension Cable
DPS
Switches
(SPST-
NO): As
Needed
Switch #1
(SPST-NO):
Provided
Extending the DPS Circuit:
A: Remove the DPS jumper
B: Connect the included DPS
extension cable
C: Connect additional normally
open DPS switches as shown
to monitor additional panels.
Part Number 3080006.008 Rev. A ©2013, HES, Inc. 4
4. Installing the Handing Selector
Note: Be careful not to insert/snap the handle all the way in as the lever will lock.
2. Position the arrows to
point toward the door
edge as shown above.
1. Insert handing
selector into lock.
Door edge
3. Secure cam with screw.
Part Number 3080006.008 Rev. A ©2013, HES, Inc. 5
This page intentionally left blank
Part Number 3080006.008 Rev. A ©2013, HES, Inc. 6
This page intentionally left blank
Part Number 3080006.008 Rev. A ©2013, HES, Inc. 7
WARNING
For Technical Support please call 1-800-626-7590
FCC Statement
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Operation with non-approved equipment is likely to result in interference to radio and TV reception. The user is cautioned that
changes and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate
this equipment.
IC Statement
This device complies with Industry Canada license-exempt RSS standards(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation.
Conformité aux normes FCC
Cet équipement a été testé et trouvé conforme aux limites pour un dispositif numérique de classe B, conformément à la Partie 15
des règlements de la FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans
une installation résidentielle. Cet équipement génère, utilise et peut émettre des fréquences radio et, s'il n'est pas installé et utilisé
conformément ment aux instructions du fabricant, peut causer des interferences nuisibles aux communications radio. Rien ne
garantit cependant que l'interférence ne se produira pas dans une installation particulière. Si cet équipement provoque des
interférences nuisibles à la réception radio ou de télévision, qui peut être déterminé en comparant et en l'éteignant, l'utilisateur est
encouragé à essayer de corriger les interférence par une ou plusieurs des mesures suivantes:
Réorienter ou déplacer l'antenne de réception.
Augmenter la distance entre l'équipement et le récepteur.
Branchez l'appareil dans une prise sur un circuit différent de celui auquel le récepteur est connecté.
Consultez votre revendeur ou un technicien radio / TV pour assistance.Avertissement
Les changements ou modififications à cet appareil sans expressément approuvée par la partie responsable de conformité pourraient
annuler l'autorité de l'utilisateur de faire fonctionner cet équipement.
Conformité aux normes IC
Cet appareil est confrome avec Industrie Canada exempt de license RSS standard(s).
Son fonctionnement est souimes aux deux conditions suivantes:
(1) cet appareil ne peut causer d’interférences, et
(2) cet appareil doit accepter toute interference, y compris des interférences qui peuvent provoquer un fonctionnement indésirable
du périphérique.
Part Number 3080006.008 Rev. A ©2013, HES, Inc. 8
Loading...