Hanatech DCNPRO Users Manual

Test Report No.: GETEC-E3-04-018

FCC Class B Certification

APPENDIX G

: USER’S MANUAL

EUT Type: Automotive Handheld Scantool

FCC ID : RZXDCNPRO

ٻ ٻ ٻ ٻ

CHAPTER 1 SAFETY AND WARRANTY

I. SAFETY INSTRUCTIONS

II. SAFETY PRECAUTIONS

III. WARRANTY SERVICE

FCCRF INTERFERENCE STATEMENT

………….

1 - 2

1 - 4

1 - 6

1 - 8

Hanatech Co., Ltd.

Chapter 1

Safety and Warranty

About this Manual

The contents of this manual are the result of contributions by dozens of individuals all who have added their vital expertise and experience to the evolution of the contents of this manual.

The information contained in this manual may contain printing errors and is subject to change without notice according to product upgrade. Hanatech shall not be liable for errors contained herein or for incidental or consequential damage in connection with the furnishing, performance, or use of this material.

No part of this manual may be photocopied, reproduced, or translated to another language in any way without the prior written consent of Hanatech Co., Ltd.ٻ

Using this Manual

It is recommended that the user become familiar with the operating procedures, terminologies and information contained within this user’s manual. This will help to increase the user’s effectiveness with this equipment

Vehicle system familiarity

While this equipment provides very powerful functions with extensive vehicle coverage, it cannot replace knowledge and skill. To get the most out of this equipment, a full understanding of vehicle systems is required. It is recommended that the equipment be used in conjunction with the original service manual for the vehicle being tested.

The equipment is designed for use by trained service personnel and this manual assumes that the service technician who is going to use this equipment has a familiarity with vehicle electronic control systems, however, the latest service manuals and bulletins should always be referenced before using this equipment.ٻ

ٻٻٻ

jGXGTGXG

USER MANUAL For DCN Scanners

I. SAFETY INSTRUCITONS -----------------------

Thank you for purchasing DCN scanners. To get the maximum performance of

the equipment, please carefully read this manual first, and keep it at hand.

On delivery inspection

When the equipment is delivered, a check should be made for any damaged or missing components. If the unit is damaged or fails to operate according to the specifications, contact your local distributor or the manufacturer, Hanatech Co., Ltd., Hana bldg., 80-1 Songjung-dong, Gumi-shi, Kyung-buk Republic of Korea 730-090. In the unlikely event the equipment requires shipping back to the manufacturer, please use the original packing material.

Safety symbols

The following symbols are used throughout this manual:

DANGER

WARNING

SYMBOL Description

This mark means that dangerous consequences may arise, with the possibility of death or serious injury to the user, if the machine is handled incorrectly.

This mark means dangerous consequences may arise, with the possibility of somewhat serious injury to the user and or damage to the machine and facilities, if the equipment is handheld incorrectly.

This symbol is affixed to locations on the equipment where

the operator should consult corresponding topics in this manual (which are also marked with the

using relevant functions of the equipment. In the manual, this symbol indicates explanations that are particularly important that the user is expected to read the manual before using the equipment.

symbol) before

This symbol represents DC (Direct Current)

jGXGTGYG

Safety guideline

In order to ensure proper operation and satisfactory performance, observe the

cautions listed below.

This equipment is designed to comply with IEC61010-1 safety standards, and has been tested for safety prior to shipment. Excessive high voltage measurement or improper operation could result in personal injury, as well as damage to the equipment or the vehicle. Please read this manual carefully and be sure that you understand its contents before using the equipment.

The manufacturer disclaims all responsibility for any accident except for that resulting due to defect in its product.

Hanatech Co., Ltd.

DANGER

Chapter 1

WARNING

For safety reasons, this equipment should not be used to

measure circuits carrying more than 30Vrms or 42.4V peak.

To avoid electrical accident that could result in injury or

death, do not measure voltage in excess of these limitations.

Maximum rated measurable voltage is 30Vrms or 42.4V

peak.

jGXGTGZG

USER MANUAL For DCN Scanners

II. SAFETY PRECAUTIONS -----------------------

DANGER

When an engine is running, keep the workshop area WELL

VENTILATED or attach a building exhaust removal system to the

engine exhaust system. Engines produce carbon monoxide, an

odorless and poisonous gas that causes slower reaction time

and may lead to serious injury or death.

WARNING

Brakes and wheel blocks

Apply the hand brake and block the wheels before using the test

equipment. It is highly recommended to block the wheels on

front-wheel drive vehicles because the hand brake does not hold

the driving wheels.

Drive Test

Do not drive the vehicle and operate the test equipment at the

same time. Any distraction may cause an accident. Have one

person operate the test equipment while the other person drives

the vehicle.

Never place the test equipment in front of you when driving the

vehicle because the test equipment may hit your body and cause

serious injury when the air bag inflates.

Do not try to test the SRS air bag system while driving the

vehicle as unintended air bag inflation may result.

jGXGTG[G

Hanatech Co., Ltd.

Chapter 1

Engine Compartment

Maintain sufficient clearance between moving components or

belts while using the test equipment in the engine compartment.

Moving components and belts may catch loose clothing, test

cables or a part of your body and cause damage or personal

injury.

Electrical Components

Always turn the ignition key OFF when connecting or disconnecting electrical

components unless otherwise instructed.

Vehicle Battery

DCN equipments are designed to prevent damage from reverse polarity battery cable

connection, however, it is always highly recommended to always ensure correct

polarity terminal connection.

Never lay the test equipment on vehicle battery. You may short the terminals and may

cause damage to your body, the test equipment or the battery.

To avoid damaging the test equipment or displaying false data, make sure the vehicle

battery is fully charged and the connections to the electronic control module are clean

and tight.

The warning messages above and the safety messages contained hereinafter cover

situations Hana Tech is aware of. Hana Tech cannot know, evaluate or advise you as

to all of the possible hazards. You must make sure that any conditions or service

procedures encountered do not jeopardize your personal safety.

jGXGTG\G

USER MANUAL For DCN Scanners

III. WARRANTY SERVICE -------------------------

Warranty Period

In principle, DCN products are warranted to the consumer to be free of defects in

material and workmanship for the period of 3 years after the date of purchase.

If the product is found defective during this period, the product can be returned to

Hana Tech and will be repaired or replaced free of charge.

Freight and repair Cost

For the repair of head unit, Hana Tech covers the freight cost for the service during

one year from the date of purchase, and you can send the troubled unit to your local

distributor without having to pay the freight cost. You should consult with your local

distributor about the validity of remaining warranty period before sending the unit.

For the remaining two years, you are liable for any international cost incurred. Repair

or replacement will be provided free of charge.

When the warranty period is expired after three years, the customer must pay the

round trip freight and the repair or replacement cost.

Upon delivery

Hana Tech inspects all the ordered product parts and components are included in the

package before shipment, and includes the original copy of pre-shipment inspection

report in the box. As soon as the product is delivered to you, please ensure

everything you ordered is properly checked and included referring to the pre-shipment

inspection report. If there is anything missing or damaged, you must notify the local

distributor immediately within 3 working days from the delivery date for free of charge

replacement of the parts.

In case of trouble

If you encounter any malfunction or trouble with the equipment, please refer to the

Trouble Shooting chapter in this manual. If the problem cannot be solved, please

contact your local distributor for assistance. For early identification of a fault or error,

jGXGTG]G

Hanatech Co., Ltd.

your local distributor will require the following details:

1. Symptom of problem you are experiencing

2. Serial number of the head unit

3. Vehicle information: Which specific car were you testing when the problem

occurred – Model name, Model year and system ID number if available (for Mitsubishi,

Subaru and Suzuki only: Refer to Japanese car chapter for details)

Chapter 1

Warranty Void

Even in the effective warranty period, if the problem is found to be caused by any of

the followings, Hana Tech charges the cost for round trip freight and actual cost for the

service to the customer, and the shipment back to the customer will be suspended

until the customer’s payment is duly made

1. Evidence of improper use or application of the product ignoring the cautions and

warnings stipulated in the user’s manual

2. Intentional damage or modifications to the product or user’s attempt to repair

without proper authorization

3. Any damage caused by Force Majeure including war and natural disaster

4. Loss of time, inconvenience and other consequential damage or loss

Warranty void seal

In addition to the above mentioned warranty void conditions, warranty service is not

provided in case the warranty void seal is broken or removed.

If you remove the head unit safety boot, you will see a yellow round sticker covering

one of the screw holes in the back. Please be careful not to break this seal and never

try to open the head unit without direct authorization from the manufacturer.

Bought in other countries

Only the products properly supplied by the contracted authorized local distributors are

recognizable for free of charge warranty service. Any equipment bought outside the

contracted national territory of your local distributor will be charged for service.

jGXGTG^G

USER MANUAL For DCN Scanners

FCC RF INTERFERENCE STATEMET

Note

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

The equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does not cause harmful interference to radio or television reception

which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna

- Increase the separation between the equipment and receiverG

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connectedG

CAUTION

Changes or modification not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NO

CAUSE HARMFUL INTERFERENCE. AND (2) THIS DEVICE MUST ACCEPT AN

INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.G

jGXGTG_G

ٻ ٻ ٻ ٻ

CHAPTER 2 SPECIFICATION AND PARTS

I. SPECIFICATION

II. PART LIST

A. Head unit and basic supplies 2 - 3

B. Diagnostic Adapters 2 - 6

C. Spare parts 2 – 13

D. Optional Supplies 2 – 13

………….

2 – 1

2 – 3

Hanatech Co., Ltd.

Chapter 2

Specification and Parts

I. Specification -----------------------------------

A. Hardware

CPU: 16bit, 33MHz

RAM: 1 Mbyte (SRAM)

Program Cartridge Memory: 128Mbytes built-in Flash Memory

Display: 320Ý240 Monochrome Graphic LCD with Back Light

Key Pad: 20 membrane keys, embossing type

Com Port: USB and RS232

Printer: General PC printer

Power: DC 8~18V, 600mA or higher

B. Environmental Specification

Indoor use only

Operating temperature: Max 50ଇ / 122൓

Maximum relative humidity: 80% (up to 31ଇ/88൓) and 50% (40ଇ/104൓ or

higher)

Installation overvoltage categories: CATซ

Maximum measurable voltage: DC 30V Max

Pollution degree 2

Max. Altitude: Up to 2000m

jGYGTGXG

USER MANUAL For DCN scanner

C. Mechanical Dimensions

Length: 222ໄ / 9 "

Width: 187ໄ / 7.5"

Height: 51ໄ / 2 "

Weight: 950g / 2.1 lb (head unit only)

Body Color: Dark Grey

Safety Boot Color: Yellow / Blue / Red

All specifications are subject to change without notice for the purpose of product

and quality improvement.

jGYGTGYG

Hanatech Co., Ltd.

Chapter 2

II. Part List -----------------------------------------

A. Head unit and basic supplies

1. Head Unit

- Made of strong ABS resin, each

unit has passed internal impact

test before shipment.

- As the inner surface is coated with

anti-electromagnetic interference

material, it neither interferes the

other electronic devices nor gets

interfered by the other equipments.

(P/N: 1000-0005)

2. Safety Boot (P/N: 2002-0030)

- Flexible plastic cover that protects the head unit from physical,

chemical and electrical damage

Basic color is blue, however, it can be changed according to the

distributor’s demand.

jGYGTGZG

USER MANUAL For DCN scanner

3. Carry Case (P/N. 3003-0003)

Provides convenient transportation and

the protection of the head unit and other

components from outer physical impact

during the transportation and storage.

Carry case is provided when purchasing

the head unit and at least one software

package together. Includes keys and

dial lock

4. Main Data Link Cable (P/N. 3001-0001)

ڈٻ Connects vehicle side DLC and DCN scanner head unit for data

transmission.

ڈٻ

Connecting parts on both ends

are exactly same, therefore,

simply put any one end to the

head unit, and then hook the

other end to the vehicle side

DLC after connecting an

appropriate adaptor

5. Power Cable 1 – Cigarette Lighter

Supplies power to the head unit

ڈٻ

from the cigarette lighter socket.

Used when DLC is located near

(P/N. 3000-0004)

the driver or passenger seat and

power is not supplied through

DLC.

ڈٻ LED lights on both ends turn ON

when power is properly supplied.

The metal plunger part in the end of cigarette lighter connector is

ڈٻ

jGYGTG[G

Hanatech Co., Ltd.

removable by unscrewing for the fuse replacement. It may become

loose over repeated use, therefore, it is highly recommended to check if

it is tightly screwed frequently. A set of plunger parts are included in the

basic supplies. Refer to spare parts section hereinafter.

ڈٻ The rated voltage and current for this power cable are 12V and less than

2A.

Chapter 2

6. Power cable 2 – Vehicle Battery

- Supplies power from the vehicle battery when the DLC is located in

the engine bay or when using the oscilloscope or multi-meter

functions

(P/N. 3000-0005)

- Connect each of the two

alligator clips to the battery

terminal of the correct

polarity with caution.

Must be used together with

the Power Cable 1. Insert

the cigarette lighter adaptor of the Power Cable 1 into the socket,

and connect the other end to the head unit.

- Red LED light turns ON when power is properly supplied from the

vehicle battery.ٻ

jGYGTG\G

USER MANUAL For DCN scanner

B. Diagnostic Adapters

Diagnostic adapters are sold separately, therefore check if all the adapters

you ordered are included in the package upon delivery.

There are two types of adapters: capsulated and wired types.

Most of DCN scanner DLC adapters are capsulated for better durability and

storage, however, sometimes it is difficult or almost impossible to connect the

capsulated adapter to vehicle side DLC when it is located deep inside

beneath the dashboard. We use wire type adapters for the cars such as

Hyundai and Kia that we were reported to have such connecting difficulties.

Capsule type Wire type

1. OBD2 Standard Adapter

(P/N. 3001-0010)

Used for all OBD generation 2 and EOBD

compatible vehicles. Vehicle side DLC is

generally located near the driver’s seat and

most frequently found beneath the dash panel.

2. Toyota / Lexus 17Pin Rectangular Adapter

Used for the diagnosis of Toyota and Lexus

of OBD generation 1. Vehicle side DLC of

this type is generally located in the engine

compartment.

(P/N. 3001-0011)

jGYGTG]G

Hanatech Co., Ltd.

Chapter 2

3. Toyota/Lexus 17Pin Semi-circular Adapter (P/N. 3001-0012)

Also used for the diagnosis of Toyota and

Lexus of OBD generation 1.

The vehicle side DLC is generally found

beneath the dashboard.

Refer to the following warning message.

WARNING

The appearances of this adapter and MAZDA 17Pin adapter are exactly same, however, the internal wiring and circuit are different. Check the

engraved name and the body color of the adapter carefully before use. Improper adapter connection may result in serious malfunction of either control system and DCN scanner head unit.

4. Honda 3 Pin Adapter and 2 Pin Jump Wire

(P/N. 3-pin: 3001-0014, 2-pin wire: 3001-0023)

3-pin adapter is used for the diagnosis of Honda

cars of OBD generation 1 that support DTC

read and erase as well as data stream.

Older Honda cars have 2-pin DLC that supports

DTC read only. The jump wire is used for these

older cars to bridge the 2-pin DLC terminals.

The vehicle side DLC is generally located under

the dashboard or the glove box.

jGYGTG^G

USER MANUAL For DCN scanner

5. Mitsubishi and Hyundai 12Pin Adapter (P/N. 3001-0001)

Used for the communication

with Mitsubishi and Hyundai

cars of OBD generation 1.

A wire type adapter is provided

as the connecting difficulties of

capsule type adapter in quite a

few Hyundai cars were

reported.

6. Mitsubishi 12+16pin dual headed adapter (P/N: 3001-0030)

Used for the communication with

Mitsubishi cars with both of 12-pin

OBD1 and 16-pin OBD2 adapters

on-board.

Refer to the Mitsubishi section,

Chapter 6 for details.

7. Nissan and Samsung 14Pin Adapter (P/N. 3001-0006)

Used for the communication with Nissan cars

of OBD generation 1 and all Samsung

passenger cars.

Vehicle side DLC is generally found under the

dash or inside the fuse box.

8. Mazda 17Pin Adapter (P/N. 3001-0013)

Used for the communication with Mazda cars

of OBD generation 1.

Vehicle side DLC is generally located in the

engine compartment.

Refer to the warning message in the next page:

jGYGTG_G

Hanatech Co., Ltd.

Chapter 2

WARNING

The appearances of this adapter and Toyota 17Pin SEMI-CIRCULAR adapter are exactly same, however, the internal wiring and circuit are different. Check the

engraved name Improper adapter connection may result in serious malfunction of either control system and DCN scanner head unit

and the

body color

of the adapter carefully before use.

9. Subaru 9Pin Adapter

Used for the communication with Subaru cars of

OBD generation 1.

The vehicle side DLC is generally located

beneath the dashboard.

(P/N. 3001-00)

10. GM Daewoo 12Pin Adapter

(P/N. 3001-00)

Used for the communication with Daewoo cars

of OBD generation 1.

The vehicle side DLC is generally located

beneath the glove box, door side.

11. Kia 6Pin Adapter (P/N. 3001-0003)

Used for the communication with old

Kia cars of OBD generation 1.

Only the Diagnostic Trouble Code

reading function is available for the

cars with this type of adapter as only

the slow pulse signal is transmitted

through the vehicle side DLC.

The split wire of the adapter is to be connected to the ground terminal of

the vehicle side DLC.

jGYGTG`G

+ 49 hidden pages