Hanasis HW-3000 E-manual

HW-3000

e-Manual

※ Please read and learn the manual carefully for your safety and proper way of use.

Safety precautions

HW-3

000 preview

Specification & options

Locations

ㆍParts description

ㆍI/O port

ㆍRating label zone

Contents

System Introduction

Remove the protective tape

Adjusting Viewing Angle

Connecting DC Power
Supply Cable & System on

System Installation

BIOS Setup

BIOS

Touch Screen

MSR

Kitchen Printer

Using the product

Winclon (Backup)

Winclon (Restore)

POS Driver & Utility

System Block Diagram

MotherBoard Layout

Setting Jumper

Appendix

I/O Pin Assignment

MSR

STAND

HDD

Assembly & Disassembly

REAR COVER

EMI

WALL MOUNT

9.7” DUAL(TOUCH) MONITOR

ㆍInstallation / Connect cable

ㆍSystem Setup

15” DUAL(TOUCH) MONITOR

ㆍInstallation / Connect cable

ㆍSystem Setup

NFC

ㆍInstallation / Connect cable

ㆍBIOS Setup

BARCODE SCANNER

ㆍInstallation / Connect cable

ㆍReset Default Setup

ㆍCOM 1, COM 2/ 3

ㆍCOM 4, VGA

ㆍUSB, DC-IN, DC-OUT

ㆍPS/2 MOUSE, PS/2 KBD

ㆍLAN, MSR

Contents

Assembly &

Disassembly

BIOS

Appendix

Using the product

Safety precautions

Do not block the ports(holes), Vents, etc, of the system and do not insert objects.

Damage to a component within the system may cause electric shock or fire.

Do not touch the system plug or power cord with wet hands. There is a danger of electric shock.

Do not exceed the standard capacity(Voltage/current) of a multiplug or power outlet extension when using it for the product.

There is a danger of electric shock or fire hazard.

Do not unplug the power cord by pulling the cable only. If the cord is damaged, it may cause electric shock.

Connect the power cord to the AC adaptor firmly. Use only the AC adaptor supplied with the product.

Otherwise, there is a danger of fire due to an incomplete contact.

Do not use the system in a humid location such as a bathroom or sauna.

Please use the system within the recommended temperature and humidity range(10~32˚C, 20~80% RH).

Avoid direct sunlight when the system is in an air-tight location such as inside a vehicle.

There is a danger of a fire hazard. The system may overheat and also present opportunity to thieves.

System Installation

System Introduction

Safety precautions

HW-3000 preview

Specification & options

Locations

For your security and to prevent damage, please read the following safety instructions carefully.
Failing to follow instructions marked with this symbol may cause personal injury and even fatality.

Contents

Assembly &

Disassembly

BIOS

Appendix

Using the product

System Installation

System Introduction

Safety precautions

HW-3000 preview

Specification & options

Locations

Thank you for purchasing Hanasis's POS.

(Product specifications may differ according to region and may be changed without prior notice)

■ System preview

HW-3000 preview

Class-A digital device

A digital device that is marketed for use in a commercial, industrial or business environment,

exclusive of a device which is marketed for use by the general public or is intended to be used in the home.

This product is developed and tested on the basis of our reliability and outstanding technology.

This product has applied exclusive and emotional design and also provides wide expandability such as barcode scanner or NFC.

This product has applied low power atom platform design, 15” Window(TFT) touch screen and 9.7” dual monitor expandability.
This will allow users to save maintainance cost and will provide comfortable user experience.

This product is designed for users to fix easily by using hand screws in system main body and stand, and also by decreasing the number of screws.

This product has acquired domestic and international standard, applied a technology patent that is created by Hanasis.

registered trademark

The symbol mark is the foundation element that symbolizes the Hanasis corporation and it is also a symbol of communication at both home and abroad.
The basic concept is a leading IT industry. It embodies Hanasis's corporate goal to link world faster by using advanced IT technology.
The symbol mark express Hanasis's industry representative. The symbol expresses the image of network envrionment and advanced technology in dynamic way.

Contents

Assembly &

Disassembly

BIOS

Appendix

Using the product

System Installation

System Introduction

Safety precautions

HW-3000 preview

Specification & options

Locations

(Product specifications may differ according to region and may be changed without prior notice.)

◆ Specification ◆ Options

Specification & options

OS
Wall Mount
Touch Panel

Dual Display

iButton

MSR

Barcode Scanner

Color Product

Smart IC Card

Microsoft® Windows7, POSReady7 / 2009, windows XP
Fixed Type , Swivel Type

(75x75, 100x100mm VESA)

15", 5-Wire Resistive (Bezel type / Bezelless type)

9.7”, TFT-LCD, 1024x768, LED panel (Touch)
15”, TFT-LCD, 1024x768, LED panel

Probe(USB), Dallas key

ISO Track2 , Track 1&2 , Track 1&2&3

USB Module(Internal) type, 1D, 2D

IC Card Reader(USB), EMV Level#1

White Black

Processor(CPU)

Chipset

Memory

HDD

Display

VGA / DVI
HDMI
LAN
Serial(RS-232C)
Parallel(LPT)
PS/2

USB

Audio
Speaker

Expansion Interface

Cooler & FAN

Power Adaptor

Dimension(mm)
Weight

Intel

®

Intel

®

Celeron® 1037U Dual-Core (1.8GHz, 2M Cash)

NM70

2GB DDR3 1333MHz, SoDIMM (Up to 8GB)

2.5”, SATA-III 320GB~ or SSD 32GB~
m-SATA (32GB~)
15", 1024 X 768, 24Bit
Luminance : 250 cd/㎡, Backlight : LED

1EA VGA (DSUB15) Intel® HD Graphics 2500

-

2 EA (Intel® Gigabit LAN)

4 EA (DSUB-9p x 3EA / RJ-45 x 1EA)

-

2 EA (Keyboard / Mouse)
4 EA (I/O) (USB2.0)
2 EA (Front) (USB2.0)

2 EA (Line-Out / MIC-In) Realtek ALC269 HD2.1 Audio

1 EA (1W)

1 EA PCIe Socket

1 EA Full Size Mini PCIe Socket (m-SATA)

Fanless
60[W] Adaptor
Input AC 100~240V/50~60HZ, DC 12V/5A
364(W) x 332(H) x 200(D) (Normal Angle, With Stand)

7.3kg

NFC

Serial Module(Interal) type, SSCPRO NFM1V0

Contents

Assembly &

Disassembly

BIOS

Appendix

Using the product

System Installation

System Introduction

Safety precautions

HW-3000 preview

Specification & options

Locations

ㆍParts description

ㆍI/O port

ㆍRating label zone

Parts description

(Product specifications may differ according to region and may be changed without prior notice.)

Power supply lamp
Error lamp

Reset button

Card reader(MSR)

Exteral USB(2port)

HDD lamp
LAN lamp

Dual(touch) monitor

Cover cable

NFC reader(Option)

Barcode scanner(Option)
Camera(Option)

Cable vent

Cable space

(9.7” / 15”)

Power button & Power supply lamp

1. Card reader (MSR) : Device that recognizes credit cards.

※ power supply lamp : green light / error lamp : red light / reset button : Use when initializing the Card reader.

2. HDD lamp : The light will be turned on when the hard disk is reading or writting data.

3. LAN lamp : The light will be turned on when connected to the internet.

4. Power supply lamp : The light will be turned on when the system is on.

5. 9.7” / 15” Dual(touch) monitor : Option

6. Barcode scanner / NFC reader : Option

7. Cover cable : Disassemble the cover and then you can connect the I/O port.

8. Cable space / vent : Disassemble the cover and then you can reorganize the cables that are connected.

Contents

Assembly &

Disassembly

BIOS

Appendix

Using the product

System Installation

System Introduction

Safety precautions

HW-3000 preview

Specification & options

Locations

ㆍParts description

ㆍI/O port

ㆍRating label zone

I/O port

1. PS/2 (MOUSE)

2. PS/2 (KBD)

3. D-SUB 9PIN serial(COM)

4. D-SUB 15PIN VGA

5. RJ-45 LAN

6. USB 2.0

7. AUDIO port (LINE-OUT)

8. MIC port (MIC-IN)

9. DIN 4PIN 12V DC-IN

10. 12V DC-OUT

11. RJ-45 8PIN COM

12.

RJ-45 8PIN MSR86%W\SH

13. HDD

PS/2 type of mouse

PS/2 type of keyboard
Equiments that use serial port such a barcode scanner and printer

Dual(touch) monitor

Internet connection

USB keyboard, USB mouse, NFC reader etc.

External speakers

Externa

l mic

Adapt

or jack that provides system power

Dual(touch) monitor power jack

Equiments that use serial port

0DJQHWLF6WULSH5HDGHU

SSD or 2.5” HDD

(standard)

OUT(12V)

COM4

MSR

(USB)

IN(12V)

POWER

HDD Tray

LAN

COM1

COM2 COM3

USB

VGA

LINE-OUT

MIC-IN

MOUSE

KBD

USB

LAN

1

3 3

5

7

2

3

4

6

121110

13

8

9

Contents

Assembly &

Disassembly

BIOS

Appendix

Using the product

System Installation

System Introduction

Safety precautions

HW-3000 preview

Specification & options

Locations

ㆍParts description

ㆍI/O port

ㆍRating label zone

Rating label zone

Before you setup the product(HW-3000).
Remove the protective tape before setup.

Contents

Using the product

Assembly &

Disassembly

BIOS

System Introduction

Appendix

Connecting DC Power
Supply Cable & System on

Remove the protective tape

Adjusting Viewing Angle

Remove the Protective Tape

Protective Tape

System Installation

Contents

Assembly &

Disassembly

BIOS

System Introduction

Appendix

Connecting DC Power
Supply Cable & System on

Remove the protective tape

Adjusting Viewing Angle

System Installation

5˚

For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference.
You are able to adjust the monitor's angle from 5°to 50°.

Adjusting Viewing Angle

50˚

Using the product

Connect the power cord to the AC adaptor firmly. Use only the AC adaptor supplied with the product.
Otherwise, there is a danger of fire due to an incomplete contact. Do not touch the system plug or power cord with wet hands

Contents

Assembly &

Disassembly

BIOS

System Introduction

Appendix

Remove the protective tape

Adjusting Viewing Angle

System Installation

1

cover cable

stand
side cover

grab

stand
side cover

1

OUT(12V)IN(12V)

POWER

① Separate the Cover Rear Stand, as shown in drawing.

② Separate the Cover Cable.

③ Connect the Adaptor Cable.

④ Press Power button to turn the system on.

3

3

Connecting DC Power Supply Cable & System on

Please always check the directions.

Connecting DC Power
Supply Cable & System on

Using the product

Contents

System Installation

Assembly &

Disassembly

BIOS

System Introduction

Appendix

MSR

Winclon (Backup)

Kitchen Printer

Winclon (Restore)

POS Driver & Utility

Touch Screen

Do not apply a severe impact to the touch screen or press the screen with a sharp object such as a ball-point pen.
This may damage the touch screen.

■ Touch Point Setup

Touch Screen

When you use the touch screen for the first time or the pointer does not precisely match your touch, calibrate the touch screen
in the ‘eGalaxTouch’. The calibration process for the touch screen may differ depending on the operating system and may not be available in
some operating systems. The following descriptions assume the Windows POSReady2009 operating system.

① Click Start→All Programs→eGalaxTouch→Configure Utility

② Click the 'Tools' tab and ‘4Points Calibration’

③ When the Calibration window appears, touch the point represented by the “+”.

④ The “+” is displayed from the bottom left to the top left of the screen sequentially.

⑤ The touch screen input points are calibrated.

Using the product

Contents

System Installation

Assembly &

Disassembly

BIOS

System Introduction

Appendix

MSR

Winclon (Backup)

Kitchen Printer

Winclon (Restore)

POS Driver & Utility

Touch Screen

Using the product

Learn the proper way of using card reader before using the product.
When the card is inappropriately recognized, the red ligth will be turned on with the beep sound.

① grab your credit card as the picture shows.

※ make sure the magnetic side of the card towards out side.

② Push your credit card in the direction of the arrow.

③ Slide down your credit card gently in the direction of the arrow.

■ Proper way of using the card reader

MSR

1

2

3

Contents

System Installation

Assembly &
Disassembly

BIOS

System Introduction

Appendix

MSR

Winclon (Backup)

Kitchen Printer

Winclon (Restore)

POS Driver & Utility

Touch Screen

Using the product

In order to connect POS device with kitchen printer, please regard to the following connection drawing.
You must use the interchangable gender that is provided by Hanasis.

■ cable connection specification for kitchen printer serial cable

Kitchen Printer

[SRP-350] [SRP-330] [TM-T83] [SRP-350] [TM-T83]

1: N.C

2: DSR

3: TXD

4: RXD

5: RTS

6: CTS

7.GND

8: DTR

POS(COM4)

1: N.C

2: DSR

3: TXD

4: RXD

5: RTS

6: CTS

7.GND

8: DTR

interchangable gender

(RJ45-DB25)

1

8

8

1

interchangable gender

Extension Cable

Extension cable insert

※ The interchangable gender will only be enclosed with
the kitchen bell when you order a Kitchen printer.

Connect the printer

Contents

System Installation

Assembly &

Disassembly

BIOS

System Introduction

Appendix

MSR

Winclon (Backup)

Kitchen Printer

Winclon (Restore)

POS Driver & Utility

Touch Screen

Using the product

You need to connect key board before you turn the power on.

Back up your current Window user environment into restore field.
It is much easier to operate if you know where the data is being backed up.

■ HDD Backup

Winclon (Backup)

① Connect the keyboard and mouse to the system.

After turning on the system, follow the on-screen instructions:

press <F11> when the “F11 to WinClon ...” message appears on the screen within 2 to 4 seconds (PC POST process).

② When WinClon appears on the screen, press <F10> key on your keyboard or click the mouse to select “Backup”.

③ After entering the password, press the <OK> button to continue the backup. (Password: pos)

pos

Backup file location

(The programs may vary depending on different model.)

■ HDD Backup

(The programs may vary depending on different model.)

Contents

System Installation

Assembly &

Disassembly

BIOS

System Introduction

Appendix

MSR

Winclon (Backup)

Kitchen Printer

Winclon (Restore)

POS Driver & Utility

Touch Screen

Using the product

If you recover the Hard disk, all the data of the system will be deleted.
Please save all the important data in the external storage before you start recovering.

You can recover quickly despite when you are not able to boot from the OS or when having any problems.
Keyboard and mouse must be connected.

Winclon (Restore)

① Connect the keyboard and mouse to the system.

After turning on the system, follow the on-screen instructions:

press <F11> when the “F11 to WinClon ...” message appears on the screen within 2 to 4 seconds (PC POST process).

② When WinClon appears on the screen, press <F2> key or <F3> on your keyboard or

click the mouse to select “Recover recent state” or “Recover initial state”.

③ After entering the password, press the <OK> button to continue the restore. (Password: pos)

※ Recover recent state” is restored to the most recent backup of Windows.

※ Recover initial state” is restored to the factory default state.

pos

Contents

System Installation

Assembly &

Disassembly

BIOS

System Introduction

Appendix

MSR

Winclon (Backup)

Kitchen Printer

Winclon (Restore)

POS Driver & Utility

Touch Screen

Using the product

All the drivers and data that are provided with your purchase are in the D drive of Hard disk.

POS Driver and Utility

▶

It is the contents from the D:\Utility.

There are install files in each folders.

Drivers

Utility

Manual

MSR

HDD AlignTool

AdobeReader

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

■ MSR separation

MSR

MSR

(USB)

HDD Tray

Cover cable

When reassembling the card reader, you must assemble tightly otherwise the card will not be recognized by the reader.

① Separate the cover cable by pushing it upwards.

② Disconnect MSR connector.

③ Remove 2 hand screws.

④ Separate the MSR by pushing it in the direction of the arrow.

1

2

Screw

3

4

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Assembly &
Disassembly

The stand is heavy so please be careful with it. When reassembling, for your safety,
you must put the lever in the correct insertion point.

■ Stand separation

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Assembly &

Disassembly

① Lift the lever(ⓐ).

② Pull the stand in the direction of the arrow indicated.

③ Lift up and remove the stand.

Lever

Insertion Point

1

2

3

a

Stand

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Assembly &
Disassembly

Care must be taken when removing the HDD and bracket to avoid injury.
Save all your data before clicking on Shut down. Disconnect the Adaptor cable from the system.

① Separate the Cover Cable.

② Rotate(Counter Clockwise) the Hand screw.

③ Pull the HDD out of the system.

④ Separate the HDD from the Bracket HDD.

⑤ Replace the new HDD into the Bracket HDD and assemble in reverse order.

■ Hard Disk Drive Replacement

HDD

1

Cover cable

2

3

4

4

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Assembly &
Disassembly

When reassembling, please be careful not to damage
the USB port at the bottom and the power button.

1) before you lay down the product, please remove anything that could damage the product and touch panel,
and then spread a clean fabric or cloth before you start the operation.

2) The disassembling and assembling process require professionality.
If you attempt to disassemble without any expertise, it may cause product trouble so please be careful.

StandCard reader

(MSR)

Dual monitor

Cover cable

1

screw

Rear cover

USB port

Power button

2

3

■ Rear Cover separation

Rear Cover

① Separate the cover cable, dual monitor, card reader(msr), stand.

※ Please refer to related contents for the separation.

② Remove the 1 screws.

③ Separate the rear cover by pushing it in the direction of the arrow.

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Assembly &
Disassembly

1

Check the caution for disassembling before disassemble EMI.

2

3

Rear cover
Card reader
(MSR)

Dual monitor

Cover cable

Stand

Screw

EMI

■ EMI separation

EMI

① Separate the cover cable, dual monitor, card reader(msr), stand and rear cover.

※ Please refer to related contents for the separation.

② Remove the 2 screws.

③ Separate the EMI by pushing it in the direction of the arrow.

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Assembly &
Disassembly

Connect the power cord to the AC adaptor firmly. Use only the AC adaptor supplied with the product.
Otherwise, there is a danger of fire due to an incomplete contact. Do not touch the system plug or power cord with wet hands.

3

Screw

2

1

Cover cable

5

4

[ Standard ]

OUT(12V)

COM4

MSR

(USB)

IN(12V)

POWER

HDD Tray

LAN

COM1

COM2 COM3

USB

VGA

LINE-OUT

MIC-IN

MOUSE

KBD

USB

LAN

a) Dual power cable

b) USB cable (only Dual touch monitor)

c) Dual VGA cable

■ Setup & Connecting DC power supply cable

9.7” Dual monitor & Dual touch monitor - Step 1

① Separate the Cover Cable.

② Attach the 9.7” Dual Monitor.

③ Fasten 2 hand screws.

④ Connect the dual VGA cable, dual power cable and USB cable(only dual touch monitor).

⑤ Connecting DC power supply cable, reassemble the separated cover cable.

⑥ Please remove the protective film before use.

Protective Film

6

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Assembly &
Disassembly

9.7” Dual monitor & Dual touch monitor - Step 2

● Dual(Dual touch) monitor Setting

[ POSReady2009, Windows XP ]

① Turn the power on and boot up with OS.
② In the desktop, click right button,
graphics properties → <Settings> tab → <advanced> button
choose a setting that you want in display config.

[ POSReady 7, Windows 7 ]

[ Auto display setting ]

① Turn the power on and boot up with OS.
② In the desktop, click right button,
graphics properties → display → dual display choose a setting.

Extend mode
Clone mode

Choose a name of
the connected monitor.

Dual display

Monitor's name can vary
according to where
it is connected to.

Clone mode

Extend mode

The setting method may vary regarding to OS and version of graphic drivers.
Please refer to relevant website for the latest driver and detailed setting method.

If the dual-monitor is leaned , Adjust the setting by pressing
the "auto display setting button" that is located at the back of the monitor.

[ Dual touch setting ]

When using the dual touch monitor, you should be aware of that the clone mode and
extend mode has different setting method. For the detail information, please visit our website.

전원버튼 ▶

전원버튼 ▶

화면자동설정버튼 ▶

화면자동설정버튼 ▶

Dual power

Auto display setting

4

[ Standard ]

OUT(12V)

COM4

MSR

(USB)

IN(12V)

POWER

HDD Tray

LAN

COM1

COM2 COM3

USB

VGA

LINE-OUT

MIC-IN

MOUSE

KBD

USB

LAN

a) Dual power cable

b) USB cable (only Dual touch monitor)

c) Dual VGA cable

① Separate the Cover Cable.

② Attach the 15” Dual Monitor.

③ Fasten 2 hand screws.

④ Connect the dual VGA cable, dual power cable and USB cable(only dual touch monitor).

⑤ Connecting DC power supply cable, reassemble the separated cover cable.

⑥ Please remove the protective film before use.

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Assembly &
Disassembly

2

Save all your data before clicking on Shut down. Disconnect all cables and the Adaptor cable from the system.

3

Screw

1

■ Setup & Connecting DC power supply cable

15” Dual monitor & Dual touch monitor - Step 1

Cable cover

5

Protective Film

Connect 15”monitor adapter to dual power cable.

6

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Assembly &
Disassembly

15” Dual monitor & Dual touch monitor - Step 2

● Dual(Dual touch) monitor Setting

[ POSReady2009, Windows XP ]

① Turn the power on and boot up with OS.

② In the desktop, click right button,
graphics properties → <Settings> tab → <advanced> button
choose a setting that you want in display config.

[ POSReady 7, Windows 7 ]

① Turn the power on and boot up with OS.

② In the desktop, click right button,
graphics properties → display → dual display choose a setting.

Extend mode
Clone mode

Choose a name of
the connected monitor.

Dual display

Monitor's name can vary
according to where
it is connected to.

Clone mode

Extend mode

The setting method may vary regarding to OS and version of graphic drivers.
Please refer to relevant website for the latest driver and detailed setting method.

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Assembly &
Disassembly

Progress after disassembling the stand.

1) Connect the power cord to the AC adaptor firmly. Use only the AC adaptor supplied with the product.

2) You may be injured by using various tools so please ask experts for help when installing.

Install in the direction of an arrow (↑)

x 4

Install in the direction of an arrow (↑)

x 4

3

■ Wall Mount installation

Wall Mount

① Make sure that the direction of an arrow of the display bracket is upward and then fix it by 4 screws.

※ Screw specification : Machine type M4, length 13~16mm

② Make sure that the wall bracket's arrow is upward and fix the wall bracket on the wall with 4 screws.

③ Insert the main body from the top to the bottom.

1

2

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Assembly &
Disassembly

Connect the power cord to the AC adaptor firmly. Use only the AC adaptor supplied with the product.
Otherwise, there is a danger of fire due to an incomplete contact. Do not touch the system plug or power cord with wet hands.

■ Setup & Connecting DC power supply cable

6

OUT(12V)

COM4

MSR

(USB)

IN(12V)

POWER

HDD Tray

LAN

COM1

COM2 COM3

USB

VGA

LINE-OUT

MIC-IN

MOUSE

KBD

USB

LAN

[ Standard ]

NFC cable (COM2 or COM3)

NFC - Step 1

① Separate the cable cover by pushing it upwards.

② Grab the bottom of the side covers and pull them in the direction of the arrows.

③ Separate the top cover by pushing it in the direction of the arrow.

④ Pull the hooks(a) at both side at the back of the stand in the direction of the arrow and then push it upwards to separate.

⑤ Follow the instruction above to install the NFC.

⑥ Connect the cable of the NFC up with the Serial port. (COM2 or 3)

⑦ Reconnect the power adaptor cable and reassemble the separated cover.

Stand
side cover

1

Cover cable

1

grab

3

3

Stand top cover

a

a

4

Stand rear cover

5

NFC

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Assembly &
Disassembly

NFC - Step 2

● BIOS Setup (NFC Voltage)

Connect the power cord to the AC adaptor firmly. Use only the AC adaptor supplied with the product.
Otherwise, there is a danger of fire due to an incomplete contact. Do not touch the system plug or power cord with wet hands.

You need to connect key board before you turn the power on.
Please refer to our website for the detailed information about BIOS set up.

① Turn on the system and the system will start POST process.

② Press “DEL” key to enter BIOS SETUP.

③ Move and enter to the “Advanced - IT8786 Super IO Configuration” menu in BIOS.

Main Advanced Topstar Chipset

Aptio Setup Utility - Copyright (C) 2011 American

Boot Security Save & Reset

[Disabled]
[Enabled]

Launch PXE OpROM
Launch Storage OpROM

Legacy OpROM Support

Version 2.14.1219. Copyright (C) 2011 American

▶ PCI Subsystem Settings
▶ ACPI Settings
▶ CPU Configuration
▶ IDE Configuration
▶ Info Report Configuration
▶ USB Configuration

▶ IT8786 Super IO Configuration
▶ PPM Configuration

▶ IT8786 Super IO Configuration

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Assembly &
Disassembly

NFC - Step 3

Main Advanced Topstar Chipset

Aptio Setup Utility - Copyright (C) 2011 American

Boot Security Save & Reset

Discard Changes and Reset

Restore Defaults

Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.

UEFI : Built - in EFI Shell
SATA SM : TOSHIBA MQ01ABD032

Boot Override

Intel RC Version

NoYes

Save & reset

Save configuration and reset ?

Main Advanced Topstar Chipset

Aptio Setup Utility - Copyright (C) 2011 American

Boot Security Save & Reset

[Enabled]Serial Port

Serial Port 2 Configuration

Version 2.14.1219. Copyright (C) 2011 American

[Auto]

0V

12V

Change Settings

Device Settings IO=2F8h; IRQ=3;

Serial Port Voltage [0V]

5V

Serial Port Voltage

Main Advanced Topstar Chipset

Aptio Setup Utility - Copyright (C) 2011 American

Boot Security Save & Reset

IT8786

IT8786 Super IO Configuration

IT8786 Super IO Chip

Version 2.14.1219. Copyright (C) 2011 American

▶ Serial Port 2 Configuration
▶ Serial Port 3 Configuration
▶ Serial Port 4 Configuration
▶ Serial Port 5 Configuration
▶ Serial Port 6 Configuration
▶ Parallel Port Configuration

▶ Serial Port 1 Configuration

④ Select the COM2 or COM3 Configuration and Select Port Voltage.

⑤ The initial value is “0V”. Change the value to 5V for NFC.

⑥ Select the “Save & reset - Yes”. After that, Turn off the system.

Do not select 12V. (refer to No.④)

The powered COM is only COM2 and COM3. (refer to No.③)

6

OUT(12V)

COM4

MSR

(USB)

IN(12V)

POWER

HDD Tray

LAN

COM1

COM2 COM3

USB

VGA

LINE-OUT

MIC-IN

MOUSE

KBD

USB

LAN

[ Standard ]

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Assembly &
Disassembly

Connect the power cord to the AC adaptor firmly. Use only the AC adaptor supplied with the product.
Otherwise, there is a danger of fire due to an incomplete contact. Do not touch the system plug or power cord with wet hands.

■ Setup & Connecting DC power supply cable

USB cable

BARCODE SCANNER - Step 1

① Separate the cable cover by pushing it upwards.

② Grab the bottom of the side covers and pull them in the direction of the arrows.

③ Separate the top cover by pushing it in the direction of the arrow.

④ Pull the hooks(a) at both side at the back of the stand in the direction of the arrow and then push it upwards to separate.

⑤ Remove the cover that is used to be installed and replace it with the scanner cover. Follow the instruction above to install the bar code scanner.

⑥ Connect the cable of the bar code scanner up with the USB port.

⑦ Reconnect the power adaptor cable and reassemble the separated cover.

Stand
side cover

1

Cover cable

1

grab

3

3

Stand top cover

a

a

4

Stand rear cover

5

Scanner cover

※ Please remove the Protective Film before use.

barcode scanner

Contents

System Installation

System Introduction

BIOS

Appendix

Using the product

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Assembly &
Disassembly

BARCODE SCANNER - Step 2

1) Please avoid setting when the store is crowded. Please set-up forehand before the store opens or after the store is closed.
When start to set-up, stop and save all of your work.

2) When you are about to proceed to next step, please make sure that the switch of the barcode scanner is visible and
then seperate the cover. (Please refer to the installation guide)
Since you have reset the default settings, you need to press the switch and scan.

● BARCODE SCANNER Reset Default GuideaA

Please read the direction carefully and safely set up the product accordingly.
Please follow the procedure below.

1. Reset Default Settings

2. Enter Programming Mode

3. Object Detection Mode

4. Exit Programming Mode

Switch

You need to connect key board before you turn the power on.
Please refer to our website for the detailed information about BIOS set up.

Contents

System Installation

Using the product

Assembly &

Disassembly

System Introduction

Appendix

BIOS Setup

The BIOS setup enables you to configure your system hardware according to your needs.
Use the BIOS setup to define a boot password, change the booting priority, or add a new device.

BIOS Setup

① Turn on the system.
② When the booting screen image appears, press the <DEL> key to enter the BIOS Setup.
③ After a moment, the BIOS setup screen appears. (The items in the BIOS setup may differ depending on the product.)

BIOS

Contents

System Installation

Using the product

Assembly &

Disassembly

BIOS

System Introduction

I/O Pin Assignment

Setting Jumper

System Block Diagram

Appendix

System Block Diagram

MotherBoard Layout

Contents

System Installation

Assembly &

Disassembly

BIOS

System Introduction

Appendix

stem Installation

A

ssembly &

Disassembl

y

BI

OS

ystem Introduction

Append

ix

MotherBoard Layout

I/O Pin Assignment

Setting Jumper

System Block Diagram

MotherBoard Layout

Using the product

13264 5

1214

1316 15

7

28

8

9

10

11

A

27

26

25

24

20

171819212223

13

[ A ]

1

LVDS P anel Connector

2

Inverter Power Header

3

Panel Power Jumper

4

ATX 12V Power Connector

5

CPU Fan Connector

6

Chassis Fan Connector

7

SoDIMM Memory Slot (DDR3)

8

SATA Power Connector

9

SATA3 Connector

10

Clear CMOS Header

11

SATA2 Connector

12

mini PCI Express Slot(mSATA Slot)

13

Battery & Battery Connector

14

PCI-E 1x Slot

15

PCI Express Power

16

Internal Speaker Header

17

COM4 Port Power Setting Jumper

18

COM5 Port Power Setting Jumper

19

COM6 Port Power Setting Jumper

20

LPT Port Header

21

COM4 Port Header

22

COM5 Port Header

23

COM6 Port Header

24

GPIO & AMP Header

25

USB2.0 Connector

26

Front Panel Header

27

ATX/AT Mode Jumper

28

DVI Header

Contents

System Installation

Assembly &

Disassembly

BIOS

System Introduction

Appendix

■ Jumper Setup

The illustration shows how jumpers are setup.
When the jumper cap is placed on pins,the jumper is “Short”.
If no jumper cap is placed on pins, the jumper is “Open”.
The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”
when jumper cap is placed on these 2 pins.

1)

Refer to the mother board layout, check "Clear CMOS Header" (No.10) location.

■ Clear CMOS Jumper (JCMOS)

[NOTE] JCMOS allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the
computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on
JCMOS for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you
just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be
noted that the password, date, time, user default profile and MAC address will be cleared only if the CMOS battery is removed.

1) Refer to the motherboard layout,
check "COM Port Power Setting Jumper" (No.17, 18 & 19) location.

2) When changing the power, change any corresponding serial port's jumper.

■ COM(4~6) Port Power Setting Jumper (JCOM4/JCOM5/JCOM6 PWR)

With this setting, you can provide power(5V, 12V)
to the serial port of COM 4, 5 & 6.

1

2

3

Jumper cap

① Short ② Open ③ pin1 and pin2 are “Short”

Jumper pin

1

2

3

+5V

1

2

3

+12V

Setting Jumper

I/O Pin Assignment

System Block Diagram

Setting Jumper

MotherBoard Layout

Using the product

Contents

System Installation

Assembly &

Disassembly

BIOS

System Introduction

Appendix

ㆍCOM 1 ,COM 2 / 3

ㆍLAN, MSR

ㆍDC-IN, DC-OUT
USB

ㆍPS/2 MOUSE
PS/2 KBD

ㆍCOM 4 , VGA

■ COM 1 - Serial Port (DSUB 9 Pin)

IO Pin Assignment

51

96

No

RS-232 RS-422 RS-485

Signal Description

1

2

3

4

5

6

7

8

9

DCD

RXD

TXD

DTR

GND

DSR

RTS

CTS

RI

-

RX (-)

TX (+)

-

GND

-

TX (-)

RX (+)

-

-

-

Data (+)

-

-

-

Data (-)

-

-

■ COM 2 / 3 - Serial Port (DSUB 9 Pin)

51

96

No

Signal Description

1

2

3

4

5

6

7

8

9

DCD

RXD

TXD

DTR

GND

DSR

RTS

CTS

COM Power 5V or 12V

System Block Diagram

Setting Jumper

I/O Pin Assignment

MotherBoard Layout

Using the product

Contents

System Installation

Assembly &
Disassembly

BIOS

System Introduction

Appendix

ㆍCOM 1 ,COM 2 / 3

ㆍLAN, MSR

ㆍDC-IN, DC-OUT
USB

ㆍPS/2 MOUSE
PS/2 KBD

ㆍCOM 4 , VGA

■ COM 4 Port (RJ-45)

■ VGA Port (DSUB 15 Pin)

IO Pin Assignment

888

No

Signal Description

1

2

3

4

5

6

7

8

N.C

DSR

TXD

RXD

RTS

CTS

GND

DTR

6

1

No

Signal Description

1

2

3

4

5

6

7

8

9

Analog - RED

Analog - GRN

Analog - BLU

GND

GND

Analog Shield (GND)

Analog Shield (GND)

Analog Shield (GND)

N.C

No

Signal Description

10

11

12

13

14

15

GND

GND

DDC DAT

HSYNC

VSYNC

DDC CLK

11

8

1

System Block Diagram

Setting Jumper

I/O Pin Assignment

MotherBoard Layout

Using the product

Contents

System Installation

Assembly &
Disassembly

BIOS

System Introduction

Appendix

ㆍCOM 1 ,COM 2 / 3

ㆍLAN, MSR

ㆍDC-IN, DC-OUT
USB

ㆍPS/2 MOUSE
PS/2 KBD

ㆍCOM 4 , VGA

■ LAN Port (RJ-45 with LED)

■ MSR Port (RJ-45)

IO Pin Assignment

No

Signal Description

1

2

3

4

5

6

7

8

VUSB 5.0V (MSR)

USBDM (MSR)

USBDP (MSR)

GND

VUSB 5.0V (EXTRA)

USBDM (EXTRA)

USBDP (EXTRA)

GND

No

Signal Description

1

2

3

4

5

6

7

8

MD0 (+)

MD0 (-)

MD1 (+)

MD1 (-)

MD2 (+)

MD2 (-)

MD3 (+)

MD3 (-)

8888

1

8888

1

System Block Diagram

Setting Jumper

I/O Pin Assignment

MotherBoard Layout

Using the product

Contents

System Installation

Assembly &
Disassembly

BIOS

System Introduction

Appendix

ㆍCOM 1 ,COM 2 / 3

ㆍLAN, MSR

ㆍDC-IN, DC-OUT
USB

ㆍPS/2 MOUSE
PS/2 KBD

ㆍCOM 4 , VGA

■ USB Port (TYPE-A)

■ DC-IN (Power DIN-4)

IO Pin Assignment

■ DC-OUT (JACK)

No

Signal Description

1

2

3

+12V

GND

GND

No

Signal Description

1

2

3

4

VUSB (5.0V)

USB D(-)

USB D(+)

GND

No

Signal Description

1

2

3

4

+12V

GND

+12V

GND

1

3

2

4

1

3

2

1 4

System Block Diagram

Setting Jumper

I/O Pin Assignment

Mother Board Layout

Using the product

Contents

System Installation

Assembly &
Disassembly

BIOS

System Introduction

Appendix

ㆍCOM 1 ,COM 2 / 3

ㆍLAN, MSR

ㆍDC-IN, DC-OUT
USB

ㆍPS/2 MOUSE
PS/2 KBD

ㆍCOM 4 , VGA

■ PS/2 MOUSE (DIN 6 Pin)

■ PS/2 KBD (DIN 6 Pin)

IO Pin Assignment

No

Signal Description

1

2

3

4

5

6

No

Signal Description

1

2

3

4

5

6

DATA

N.C

GND

VCC +5V

CLOCK

N.C

DATA

N.C

GND

VCC +5V

CLOCK

N.C

DATA

N.C

GND

VCC +5V

CLOCK

N.C

6

4

2

5

3

1

6

4

2

5

3

1

6

4

2

5

3

1

6

4

2

5

3

1

6

4

2

5

3

1

6

4

2

5

3

1

6

4

2

5

3

1

6

4

2

5

3

1

6

4

2

5

3

1

6

4

2

5

3

1

6

4

2

5

3

1

6

4

2

5

3

1

System Block Diagram

Setting Jumper

I/O Pin Assignment

Mother Board Layout

Using the product

□ Head Office

#517 Anyang Mega Valley, 268, Hagui-ro,

Dongan-gu, Anyang-si, Gyeonggi-do 431-767, Korea

□ R&D Center · A/S Center

B-1927 Geumgang Penterium IT Tower, 282, Hagui-ro,

Dongan-gu, Anyang-si, Gyeonggi-do 431-810, Korea

T [phone] F [phone]

T [phone] F [phone]

http://www.hanasis.com