PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE
CUSTOMER SERVICE: 1-877-366-0590
OLD IRON SIDES SMOKER, CHARCOAL GRILL AND ROTISSERIE
User’s Manual ITEM# OI-0000-1 MADE IN CANADA
MON. THRU FRI. 8:00 AM TO 5:00 PM EST
EMAIL: INFO@HAMRFORGE.COM
IMPORTANT SAFETY WARNINGS
READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING AND OPERATING YOUR UNIT.
• Only use this unit on a hard, level, non-combustible, stable surface (concrete, ground, etc.)
capable of supporting the weight of the unit. Never use on wooden or other surface that could
burn.
• Proper clearance of 10 feet between the unit and combustible material (bushes, trees, wooden
decks, fences, buildings, etc.) or construction should be maintained at all times when unit is in
use. Do not place unit under a roof overhang or other enclosed area.
• For outdoor use only. Do not operate unit indoors or in an enclosed area.
• For household use only. Do not use this unit for other than its intended purpose.
• We recommend the use of a Charcoal Chimney Starter to avoid the dangers associated with
charcoal lighting fluid. If you choose to use charcoal lighting fluid, only use lighting fluid
approved for lighting charcoal. Carefully read manufacturer’s warnings and instructions on the
charcoal lighting fluid and charcoal prior to the use of their product. Store charcoal lighting fluid
safely away from unit.
• We DO NOT RECOMMEND using accelerants in any of our products.When using charcoal
lighting fluid, allow charcoal to burn with unit lid and door open until covered with a light
ash(approximately 20 minutes). This will allow charcoal lighting fluid to burn off. Failure to do
this could trap fumes from charcoal lighting fluid in unit and may result in a flash fire or explosion
when lid is opened.
• Do not use gasoline, kerosene or alcohol for lighting charcoal. Use of any of these or similar
products could cause an explosion possibly leading to severe bodily injury.
• Never add charcoal lighting fluid to hot or even warm coals as flashback may occur causing
severe burns.
• Place unit in an area where children and pets cannot come into contact with it. Close
supervision is necessary when unit is in use.
• Do not leave unit unattended when in use.
• When adding charcoal and/or wood, use extreme caution and follow instructions in “Adding
Charcoal/Wood During Cooking” section of this manual.
• Do not store or use unit near gasoline or other flammable liquids, gases or where flammable
vapors may be present.
• Do not store lighter fluid or other flammable liquids or material under the unit.
Unit is hot when in use. To avoid burns:
• DO NOT attempt to move the unit.
• Brace unit with wheel chocks or other wheel blocking device so the unit does not accidentally
move.
• Wear protective gloves or oven mitts.
• DO NOT touch any hot unit surfaces.
• DO NOT wear loose clothing or allow hair to come in contact with the unit or any other hot
surfaces.
• Check grease level in grease cup often and empty or change when 3/4 full. Use extreme
caution as the smoker and its contents will be hot.
• When using as a charcoal grill, grease from meat may drip into the charcoal and cause a
grease fire. If this should happen close lid to
grease fires.
• Use caution since flames can flare-up when fresh air suddenly comes in contact with fire.
When opening the lid, keep hands, face and body a safe distance from hot steam and flame
flare-ups.
• Do not exceed a temperature of 700°F.
• Use caution when assembling and operating your unit to avoid scrapes or cuts from sharp
edges of metal parts. Use caution when reaching into or under unit.
• When opening the lid, make sure it is pushed all the way open. If lid is not fully open, it could
fall back to a closed position and cause SERIOUS bodily injury or even death.
• In windy weather, place unit in an outdoor area that is protected from the wind.
• Close lid, door, smoke stack and air intake located on the firebox door to suffocate flame.
• Never leave coals and ashes in unit unattended. Before unit can be left unattended, remaining
coals and ashes must be removed from unit. Use caution to protect yourself and property.
Carefully place remaining coals and ashes in a non-combustible metal container and saturate
completely with water. Allow coals and water to remain in metal container 24 hours prior to
disposing.
• Extinguished coals and ashes should be placed a safe distance from all structures and
combustible materials.
• With a garden hose, completely wet the surface beneath and around unit to extinguish any
ashes, coals or embers which may have fallen during the cooking or cleaning process.
suffocate the flame. Do not use water to extinguish
• After each use, clean the unit thoroughly and apply a light coat of vegetable oil to interior to
prevent rusting. Cover the unit to protect it from excessive rusting.
• Use caution when lifting or moving unit to prevent strains and back injuries.
• We advise that a fire extinguisher be on hand. Refer to your local authorities to determine
proper size and type of fire extinguisher.
• Store the unit out of reach of children and in a dry location when not in use.
• Do not attempt to service unit other than normal maintenance as explained in “After-Use
Safety” and “Proper Care & Maintenance” sections of this manual.
LIGHTING YOUR OLD IRON SIDES .
• When using as a smoker always open the lid of the unit before igniting the fire in the
firebox drawer
• Your Old Iron Sides can be used with wood logs or charcoal.
• Always operate unit with chimney trap in the wide open position.
• Open the air control dampers on the firebox to the wide open position
• Using accelerants or other synthetic products will contaminate the unit and dramatically
affect the taste of your food. Do not use any type of accelerant during lighting, liquid,
solid or otherwise.
• With the lid open and using a chimney style charcoal lighter place the chimney lighter in
the vertical position over top of the grill.
• Once the charcoal in chimney lighter has become sufficiently ignited dump the hot coals
into the firebox drawer, close drawer.
• If using spit wood to ignite your fire, build a small fire ensuring that the fire is no higher
than the drawer opening. Once ignited close drawer and lid.
SEASONING YOUR NEW HAMRFORGE OLD IRON SIDES SMOKER
• Open chimney baffles to the wide-open position.
• Open air control damper on the fire box to the wide-open position.
• Open front door and slide all available grills onto the slides inside the cook box.
• Wipe units down using vegetable oil, lard or olive oil. (do not apply to any other surfaces
other than the grill themselves)
• Using your favorite hardwood or charcoal light a fire inside the firebox drawer.
• With the lid and front door closed allow the unit to reach a minimum temperature reading
of 250 degrees Fahrenheit.
• Close each of the three air control dampers to ¼ of an inch opening
• Season the unit until the fire has extinguished itself, depending on the type of wood and
the size of fire used this process may take up to 4 hours.
USING YOUR HAMRFORGE OLD IRON SIDES AS A TRADITIONAL CHARCOAL GRILL
• Open unit lid and keep open during lighting.
• Using wood or charcoal build your fire directly on top of the smoke baffle, the smoke
baffle is the plate the separates the bottom of the cooking chamber from the firebox
drawer. For best performance use Hamrforge accessory charcoal basket part# OI-1048A
(sold separately)
• Open air intake traps on the fire box to the wide-open position.
• Open chimney traps to the wide-open position.
• Maintain fire to hold desired grill temperature between the barbeque or grill range on the
unit’s thermometer depending on the desired cooking style.
USING YOUR HAMRFORGE OLD IRON SIDES AS A ROTISSERIE
• Remove all grills from the cook box.
• Remove the 8 bolts from the side of the unit and remove the sealing plate to expose the
oblong rotisserie slots. Assemble the universal rotisserie bracket, Hamrforge part
number #OIS-1043-0 using the provided nuts and bolts. The rotisserie bracket is
symmetrical and can be installed on either the left or right side of the unit.
• Install universal rotisserie unit (not included) according to rotisserie manufacturers
instructions
• Open chimney baffles to the wide-open position.
• Using wood or charcoal build your fire directly on top of the smoke baffle, the smoke
baffle is the plate the separates the bottom of the cooking chamber from the firebox
drawer. For best performance use Hamrforge accessory charcoal basket part# OI-1048A
(sold separately)
USING YOUR HAMRFORGE OLD IRON SIDES AS AN OFFSET REVERSE FLOW SMOKER.
• Open chimney baffles to the wide-open position.
• Open air flow damper on the fire box to the wide-open position.
• DO NOT USE petrol-based accelerants or cubed fire starters to start fire.
• Using kindling wood or charcoal build your fire inside the firebox draw located inside the
fire box.
• Allow the smoker to reach 300 degrees Fahrenheit and hold this temperature for 10-15
minutes.
• Close the air flow damper down to ¼ of inch opening or until the unit reaches 225-250
degrees Fahrenheit or within the smoke range on the unit’s thermometer.
• Maintain fire as needed to hold the unit in the 225-250 range or within the smoke range
on the unit’s thermometer.
CLEANING AND MAINTENANCE.
• DO NOT USE cleaning agents or chemicals to clean the inside of the unit.
• DO NOT USE metal scrapers, steel wool or wire brushes to clean the unit. Using metal
tools to scrape the unit can damage the steel’s natural protective scale, scratch the paint
and expose the raw steel to rust and oxidation.
• Using hot water and dish soap rinse the unit and remove any large deposits by hand.
• Using a sharp-edged wood scraper remove any grease, soot and ashes.
• Close the lid and open the cook box front door. Rinse with a power washer or a garden
hose.
• Using a coarse threaded towel or rag wipe down the inside of the unit until it is dry.
• In the event your unit requires paint touch ups, use high temperature matte black paint.
Do not paint inside the cook box. Prepare the surface requiring touch-ups by cleaning
and removing and pain chips, grease or dirt. Using a Scotch-Brite® Heavy Duty Scrub
Sponge rigorously scrub the area until clean. Using rubbing alcohol wipe the surface that
requires paint. Apply paint and allow to dry according to paint manufacturers
specifications.
NON TRANSFERABLE LIMITED LIFETIME WARRANTY .
Hamrforge products are guaranteed to be free from defects in material and workmanship for the
lifetime of the original owner upon presentation of the original receipt as proof of purchase.
This Limited Lifetime Warranty covers parts deemed defective by Hamrforge Inc.and does not
cover any labor costs for diagnosis, troubleshooting, removal, installation, export duties, or
shipping, freight or other transportation to or from Hamrforge Inc.
Whether you register electronically or by mail, you should retain the original sales receipt and
other proof of original purchase, as this will be required for claims under this Limited Lifetime
Warranty.
This Limited Lifetime Warranty coverage is as follows: Hamrforge’s sole obligation under this
Limited Lifetime Warranty shall be to repair or replace, at its sole discretion, any part deemed
defective upon examination by Hamrforge Inc, upon claims received by Hamrforge Inc during the
specific warranty periods.
Customer must obtain written approval from Hamrforge Inc before performing any service or
repair by submitting a warranty claim under this Limited Lifetime Warranty. Hamrforge Inc. is not
obligated under this Limited Lifetime Warranty following any unauthorized service or repair work
and is not responsible for the charges of any repairs beyond repair or replacement, at its option,
of covered warranty claims. Repair or replacement of any parts will not extend the original
warranty coverage.This Limited Lifetime Warranty is non-transferrable for the duration of the
specific warranty periods outlined above.
To make a warranty claim under this Limited Lifetime Warranty , the owner must notify Hamrforge
Inc for troubleshooting, and subsequent instructions, as to service and replacement of defective
part(s) prior to attempting repair of a Hamrforge product
For warranty claims made outside the warranty periods commencing on the manufacture date but
otherwise covered by the period commencing on the original purchase date, a proof of purchase
shall accompany any request for warranty, unless previously submitted to Hamrforge Inc.
This Limited Lifetime Warranty does not apply to damage caused by abuse or use of the product
for purposes other than that for which it is designed. If damage is caused by lack of proper use,
assembly, cleaning, maintenance, installation, accidents, natural disasters, by unauthorized third
party attachments and/or modifications, by unauthorized service, or during shipment, this Limited
Lifetime Warranty is not applicable.
The Limited Lifetime Warranty is void on any Hamrforge product being used in any commercial
or food service setting (including but not limited to restaurant or catering use).
This Limited Lifetime Warranty does not cover damage from normal wear and tear from use of
the Hamrforge product (for example, scratches, dents, dings and chipping) or changes in the
appearance of the Hamrforge product that do not affect its performance.
Hamrforge products must be operated, cleaned and maintained at all times in accordance with
the instructions in the Owner’s Manual. This Limited Lifetime Warranty will not apply if your
product has not been assembled, operated, cleaned and maintained in strict accordance with the
manufacturer’s instructions, or placed in accordance as listed in the Owner’s Manual.
Performance problems due to operator error will not be covered by the Limited Lifetime Warranty
As this is a grill/smoker, the interior may experience changes in color of surface finish. This is not
a flaw and as such is not covered under this Limited Lifetime Warranty .
There is no written or implied performance warranty on any Hamrforge product, as the
manufacturer has no control over the assembly, operation, cleaning and maintenance or the type
of fuel burned.
High ambient temperatures, excessive humidity, chlorine, industrial fumes, fertilizers, lawn
pesticides, acid and salt are some of the substances that can affect metal coatings. For these
reasons, the Limited Lifetime Warranty DOES NOT COVER PAINT, RUST OR OXIDATION on
any components during the specific warranty coverage period.
Hamrforge Inc will not be responsible for performance issues caused by environmental conditions.
Damage to painted surfaces caused by scratches, melted items, drips/spills, external scores and
residues left on these surfaces from the use of sauces, seasonings, oils, brines, abrasive
cleaners, polishes or other chemical products are not covered in this Limited Lifetime Warranty .
Any modifications to the product will void this Limited Lifetime Warranty .
You are responsible for any shipping and transportation costs related to claims under this Limited
Lifetime Warranty . Original parts required by Hamrforge Inc to be returned must be returned
prepaid.
There are no express warranties other than the limited warranties stated herein above. No
warranties whether express or implied, including, but not limited to, any implied warranties of
merchantability of fitness for a particular purpose shall extend beyond the respective warranty
periods described above.
Hamrforge Inc shall not be liable for any direct, indirect, special, consequential, incidental, or
punitive damages; lost profits or loss of use or interruption of business regardless of the form of
action or theory of liability resulting from any defect in, or use of, any Hamrforge product,
accessories and/or heating elements. In no event shall Hamrforge Inc’s obligations exceed the
purchase price of the unit. This Limited Lifetime Warranty gives the customer specific legal rights
and the customer may have other rights which vary from jurisdiction to jurisdiction. In
consideration of this Limited Lifetime Warranty , the customer agrees that any dispute related to
any Hamrforge product, or this Limited Lifetime Warranty , under the laws of Quebec, Canada.
THIS LIMITED LIFETIME WARRANTY GIVES YOU SPECIFIC RIGHTS WHICH MAY VARY
FROM JURISTICTION OR COUNTRY, WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,
STATUTORY OR OTHERWISE, EXPRESS OR IMPLIED, ALL OTHER REPRESENTATIONS
MADE BY HAMRFORGE INC OR ANY THIRD PARTY DISTRIBUTOR OR RETAILER AND ALL
OTHEROBLIGATIONS OR LIABILITIES WITH RESPECT TO THE UNIT COVERED BY THIS
LIMITED LIFETIME WARRANTY WHICH, AT THETIME OF PURCHASE OR AT ANY TIME IN
THE FUTURE, MAY BE MADE AGAINST HAMRFORGE INC, ITS OFFICERS, DIRECTORS,
EMPLOYEES, AND AGENTS. EXCEPT as expressly provided herein, HAMRFORGE INC gives
no other express or implied warranties relating to fitness for USE OF THE UNIT; merchantability
of the UNIT, fitness for a particular purpose of the UNIT, quality of the UNIT; or condition of the
UNIT. HAMRFORGE INC’S obligations shall not exceed its obligation expressly set forth in THIS
LIMITED LIFETIME WARRANTY .
For warranty claims, please verify you have registered your unit within 30 days of purchase to
validate your warranty.
QUESTIONS, COMMENTS OR TECHNICAL SUPPORT.
Please contact us at 1-877-366-0590 or by emailing us at info@hamrforge.com
HAMRFORGE INC.
451 Route 116 East,
Acton Vale, Quebec, Canada, J0H 1A0
Loading...