HAMPTON BAY H35-NG2, H35-LP2 Owners & Installation Manual

H35 Direct Vent Gas Fireplace

Owners &

Installation Manual

MODELS: H35-NG2 Natural Gas H35-LP2 Propane

WARNING: If the information in these instructions are not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury or loss of life.

FOR YOUR SAFETY Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

Installation and service must be performed by a qualiﬁ ed installer, service agency or the gas supplier.

Tested by:

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

918-838

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

www.hampton-ﬁ re.com

FOR YOUR SAFETY What to do if you smell gas: Do not try to light any appliance Do not touch any electrical switch:

do not use any phone in your building. Immediately call your gas supplier

from a neighbour's phone. Follow

the gas supplier's instructions. If you cannot reach your gas

supplier, call the ﬁ re department.

11/09/09

WARNING

HOT GLASS

CAUSE BURNS

DO NOT TOUCH

UNTIL COOLED

NEVER

TO TOUCH GLASS

CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS, AND SHOULD ST AY AWA Y TO AVOID BURNS OR CLOTHING IGNITION.

ALLOW CHILDREN

WILL

GLASS

HAMPTON

Direct Vent Freestanding Gas Stove

To the New Owner:

Congratulations! You are the owner of a state-of-the-art Hampton The H35-2 is a hand crafted appliance and has been designed to provide you with all the warmth and charm of a wood ﬁ replace at the ﬂ ick of a switch. The model H35-2 has been approved by Warnock Hersey for both safety and efﬁ ciency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a moment now to acquaint yourself with these instructions and the many features of your Hampton® Stove.

Gas Stove by REGENCY FIREPLACE PRODUCTS .

UNIT DIMENSIONS

* Unit shown with optional side shelves.

38-1/4” (972mm)

26-7/8” (683mm)

21” (533mm)

28” (711mm)

25” (835mm)

16-3/4” (425mm)

15-3/8” (391mm)

26-1/4” (667mm)

2 Hampton® H35-2 Direct Vent Freestanding Gas Stove

TABLE OF CONTENTS

UNIT DIMENSIONS

Unit Dimensions ............................................................2

SAFETY LABEL

Copy of Safety Label .....................................................4

INSTALLATION

Speciﬁ cations ................................................................6

Information for Mobile / Manufactured Homes .............6

General Safety Information............................................7

Installation Checklist ......................................................7

Clearances to Combustibles..........................................7

Locating Your Gas Stove ...............................................8

Manufactured Mobile Home Requirements ...................8

Combustion and Ventilation Air......................................8

Optional Fan Installation ................................................8

Venting Introduction .......................................................9

Installation Precautions .................................................9

Safety Precautions for The Installer ..............................9

Vent Restrictor Position .................................................9

Exterior Vent Terminal Locations .................................10

4” x 6-5/8” Rigid Pipe ..................................................11

Cross Reference Chart only ........................................11

Rigid Pipe Venting Systems ........................................13

Rotating 45o Elbow for Horizontal Terminations ..........14

Venting Arrangements .................................................14

Venting Arrangements ................................................15

Vertical Termination With Co-linear Flex System .........18

DV Stove Horizontal Vent Kit .......................................19

Dura-Vent Termination Kit ............................................21

Dura-Vent Horizontal Installations ...............................22

Dura-Vent Vertical Termination ....................................23

Converting ..................................................................25

Class-A Metal or Masonry Chimney ............................25

Cathedral Ceilings .......................................................26

High Elevation .............................................................26

Gas Connection ...........................................................26

Aeration Adjustment ....................................................27

Gas Pipe Pressure Testing ..........................................27

Conversion from NG to LP ..........................................28

Conversion to Lower BTU Rating ................................32

Optional Brick Panel ....................................................33

Log Set Installation ......................................................33

Double Door Removal .................................................34

Optional Side Shelves Installation ...............................35

Wiring Diagrams ..........................................................36

Wall Thermostat ..........................................................37

Remote Control ..........................................................37

Final Check..................................................................38

OPERATING INSTRUCTIONS

Operating Instructions .................................................38

Lighting Procedure ......................................................38

Shutdown Procedure ...................................................38

First Fire ......................................................................38

Copy of the Lighting Plate Instructions .......................39

Adjusting Flame Height ...............................................39

Automatic Convection Fan Operation..........................39

MAINTENANCE

Normal Operating Sounds of Gas Appliances .............40

Maintenance Instructions.............................................40

General Vent ...............................................................41

Maintenance ................................................................41

Log Replacement ........................................................41

Glass Replacement .....................................................41

Fan Maintenance .........................................................41

Removing Valve ...........................................................42

Installing Valve Assembly ............................................42

PARTS LIST

Main Assembly ............................................................43

Burner & Log Assembly ...............................................44

WARRANTY

Warranty ......................................................................47

Hampton® H35-2 Direct Vent Freestanding Gas Stove

SAFETY LABEL

Listed: VENTED GAS FIREPLACE HEATER / FOYER AU GAZ À ÉVACUATION

Certiﬁ ed for/Certiﬁ ée pour: CANADA and U.S.A. WN# 16478 Tested to: CGA 2-17-M91, ANSIZ21.88a-2007/CSA 2.33a-2007

MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE

Minimum supply pressure Manifold pressure High Manifold pressure Low Maximum Input Minimum Input Oriﬁ ce size Altitude

5" WC/C.E. (1.25 kPa)

3.8" WC/C.E. (0.94 kPa)

1.1" WC/C.E. (0.27 kPa) 36,000 Btu/h (10.55 Kw/h) 18,000 Btu/h (5.28 Kw/h) #33 DMS (2.87mm) 0-4500 ft/pi (0-1372m)

Pression d'allimentation minimum Pression à la tubulure d'échappement élevée Pression à la tubulure d'échappement basse Débit Caloriﬁ que maximum Débit Caloriﬁ que minimum Dimensions de l’oriﬁ ce L’altitude

FACTORY EQUIPPED FOR NATURAL GAS

Model:H35-NG2

Convertible to 30,000 Oriﬁ ce Size Maximum Input Minimum Input Altitude

#37 DMS 30,000 Btu/h (8.78 Kw/h) 14,300 Btu/h (4.19 Kw/h) 0-4500 ft/pi (0-1372m)

Dimensions de l'oriﬁ ce Débit Caloriﬁ que maximum selon Débit Caloriﬁ que minimum selon L’altitude

FACTORY EQUIPPED FOR PROPANE GAS

Model:H35-LP2

12" WC/C.E. (3.00 kPa) 11" WC/C.E. (2.74 kPa)

2.9" WC/C.E. (0.72 kPa) 34,000 Btu/h (9.97 Kw/h) 17,500 Btu/h (5.13 Kw/h) #51 DMS (1.70mm) 0-4500 ft/pi (0-1372m)

Convertible to 28,500 Btu

Oriﬁ ce Size Maximum Input Minimum Input Altitude

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and Propane Installation Code, CSA B149.1. This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a standard is not applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured (mobile) home where not prohibited by local codes. See owner's manual for details. Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, National Fuel Gas Code ou CSA-B149.1 en vigueur. Installer l'appareil selon la norme CAN/CSA-Z240, Série MM, Maison mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part 3280, Manufactured Home Construction and Safety Standard. Si ces normes ne sont pas pertinentes, utilisez la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles. Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certiﬁ ée est fournie. This vented gas ﬁ replace heater is not for use with air ﬁ lters. Ne pas utiliser de ﬁ ltre à air avec ce foyer au gaz à é v a c u a t i on . For use with glass doors certiﬁ ed with the appliance only Pour utilisation uniquement avec les portes en verre certiﬁ ées avec l'appareil

Electrical supply / Électrique 115VAC, 1.13 A, 60Hz.

NOT FOR USE WITH SOLID FUELS. / NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE

FPI Fireplace Products International Ltd. Delta, BC, Canada Made in Canada/Fabrique au Canada 918-840

Minimum Clearances to Combustibles/Degagement Minimum De Materiaux Combustibles Minimum ceiling height from top of unit:36”/914mm Minimum plafond hauteur en haut de l’appareil:

A 6-1/2”/165mm B 6”/152mm

Minimum clearance of Vent Terminal to Outside Corner & Inside Corner: with AstroCap 6"/150mm with Dura-Vent Cap 12"/300mm

C 2" / 50mm E 2"/50mm

Serial No./ No de serie

Model/Modele:

H35-NG2

Model/Modele:

H35-LP2

355

#52 DMS 28,500 Btu/h (8.35 Kw/h) 15,000 Btu/h (4.39 Kw/h) 0-4500 ft/pi (0-1372m)

ÉQUIPÉ A L'UISINE POUR GAZ NATURAL

ÉQUIPÉ A L'UISINE POUR GAZ PROPANE

DUPLICATE SERIAL NO.

This is a copy of the label that accompanies each Direct Vent Freestanding Gas Stove. We have printed a copy of the contents here for your review.

COPY OF SAFETY LABEL

For the State of Massachusetts, installation and repair must be done by a plumber or gasﬁ tter licensed in the Commonwealth of Massachusetts.

For the State of Massachusetts, ﬂ exible connectors shall not exceed 36 inches in length. For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.

The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with battery back up in the same room where the gas appliance is installed.

4 Hampton® H35-2 Direct Vent Freestanding Gas Stove

Left Side Wall

Horizontal

Pipe

Right Side Wall

NOTE: Hampton® units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

Left Side Wall

Vertical

Pipe

Right Side Wall

REQUIREMENTS

MA Code - CO Detector

(for the State of Massachusetts only)

5.08: Modifications to NFPA-54, Chapter 10

(2) Revise 10.8.3 by adding the following additional requirements:

(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL

OBSTRUCTIONS".

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR

5.08(2)(a)1 through 4.

(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by the Board; and

2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting system components; and

2. A complete parts list for the venting system design or venting system.

(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies "special venting systems", the following requirements shall be satisfied by the manufacturer:

1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and

2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

Hampton® H35-2 Direct Vent Freestanding Gas Stove

INSTALLATION

IMPORTANT MESSAGE

SAVE THESE

INSTRUCTIONS

The Direct Vent Freestanding Gas Stove must be installed in accordance with these instructions. Carefully read all the instructions in this manual ﬁ rst. Consult the building authority having jurisdiction to determine the need for a permit prior to starting the installation.

Note: Failure to follow the instructions

could cause a malfunction of the heater which could result in death, serious bodily injury, and/or property damage. Failure to follow these instructions may also void your ﬁ re insurance and/or warranty.

Note: These instructions take precedence over

Simpson Dura-Vent instructions.

SPECIFICATIONS

Fuels: H35-NG2 is approved for use with

natural gas.

H35-LP2 is approved for use

with liquefied petroleum gases (propane).

Electrical: 120V A.C. system. Circulation Fan: Variable speed, 125/75. Log Sets: Ceramic ﬁ bre, 7 per set. Vent System: Coaxial (6-5/8" outer / 4" inner

liner) rigid ﬂ ue and termination cap. The efﬁ ciency rating of the appliance is a

product thermal efﬁ ciency rating determined under continuous operating conditions and was determined independent of any installed system.

INFORMATION FOR

MOBILE /

MANUFACTURED

HOMES

AFTER FIRST SALE

This Hampton® product has been tested and listed by ITS Testing Services as a Direct Vent Wall Furnace to the following standards: CGA-2.17-M91, and ANSI Z21.88b-2007/CSA

2.33b-2007. This Direct Vent System Appliance must be

installed in accordance with the manufacturer's installation instructions and the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current CAN/CSA B149.1 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.

This Hampton® Mobile/Manufactured Home Listed appliance comes factory equipped with a means to secure the unit.

This Hampton® Mobile/Manufactured Home listed appliance comes equipped with a dedicated #8 ground lug to which an 18 gauge copper wire from the steel chassis ground must be attached.

This appliance may only be installed in an aftermarket permanently located, manufactured (USA only )or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

BEFORE YOU ST ART

Safe installation and operation of this appliance requires common sense, however, we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the following:

INSTALLATION AND REPAIRS SHOULD BE DONE BY A QUALIFIED SERVICE PERSON. THIS APPLIANCE SHOULD BE INSTALLED, REPAIRED, INSPECTED BEFORE USE AND A T LEAST ANNUALL Y BY A QUALIFIED SERVICE PERSON. MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, ETC. IT IS IMPERATIVE THAT THE CONTROL COMPARTMENT, BURNERS AND CIRCULATING AIR PASSAGEWAYS

OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERA TURES, THE APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS APPLIANCE CORRECTLY WILL VOID YOUR WARRANTY AND MAY CAUSE A SERIOUS HOUSE FIRE.

CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERA TURES, ESPECIALLY THE FIREPLACE GLASS, AND SHOULD STA Y A WA Y TO A VOID BURNS OR CLOTHING IGNITION.

YOUNG CHILDREN SHOULD BE CAREFULL Y SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.

CLOTHING OR OTHER FLAMMABLE MATERIAL SHOULD NOT BE PLACED ON

OR NEAR THE APPLIANCE.

1) Provide adequate clearances for servicing,

proper operation and around the air openings into the combustion chamber.

2) The appliance must be installed on a ﬂ at, solid, continuous surface (e.g. wood, metal, concrete). This may be the ﬂ oor , or it can be raised up on a platform to enhance its visual impact. The appliance may be installed on carpeting, tile, wood ﬂ ooring or other com- bustible material, because the appliance's base extends the full width and depth of the appliance. The Direct Vent Freestanding Gas Stove can be installed in a wide variety of ways and will ﬁ t nearly any room layout. It may be installed in a recessed position, framed out into the room, or across a corner.

3) The Direct Vent Freestanding Gas Stove is approved for alcove installations, which meet the clearances listed in the "Clearance to Combustibles" section. This unit is approved for manufactured home installations, see the "Manufactured Mobile Home Additional Requirements" section and the "Venting Arrangement" section for the required vent arrangements. If installed into a manufactured home the unit must be bolted down to the ﬂ oor.

4) This appliance is Listed for bedroom installations when used with a Listed Millivolt Thermostat. Some areas may have further requirements, check local codes before installation.

5) This appliance is Listed for Alcove installations, maintain minimum Alcove clearances as follows, minimum width of 40" (1016mm), a maximum depth of 36" (914mm), and minimum ceiling height of 64" (1626mm) from ﬂ oor to ceiling.

6) We recommend that you plan your installation on paper using exact measurements for clearances and ﬂ oor protection before actually installing this appliance. Have a qualiﬁ ed building inspector review your plans before installation.

6 Hampton® H35-2 Direct Vent Freestanding Gas Stove

INSTALLATION

GENERAL SAFETY

INFORMATION

1) The appliance installation must conform with

local Canadian Electrical Code.

2) The appliance when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the current National Electrical Code, ANSI/NFPA 70 or CSA C22.1 Canadian Electrical Code.

3) The appliance should be inspected for shipping damage before use and serv-

iced annually by a professional service person. More frequent cleaning may be

required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, and circulating air passageways of the appliance be kept clean and free from excessive lint from carpeting.

4) See general construction and assembly instructions. The appliance and vent should be enclosed when installed in or passing through a living area, where children may come in contact with it.

5) This appliance must be connected to the speciﬁ ed vent and termination cap to the outside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is ﬁ tted as per the instructions starting in the "Exterior Vent Terminal Locations" section.

6) Inspect the venting system annually for blockage and any signs of deterioration.

7) Venting terminals shall not be recessed into a wall or siding.

8) Any safety glass removed for servicing must be replaced prior to operating the appliance.

9) To prevent injury, do not allow anyone who is unfamiliar with the operation to use the ﬁ replace.

Emissions from burning wood or gas could contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

INSTALLATION

CHECKLIST

1) Locate your appliance. Refer to the following

sections:

Introduction" to "Venting Arrangements"

Section.

2) Install Optional Fan. Refer to the "Optional Fan Installation" section.

3) Set vent restrictors. Refer to the "Vent Restrictor Position" section.

4) Install venting. Refer to the following sections where applicable:

a. Check all venting requirements.

See "Venting Introduction" to "Venting

Arrangements" sections. b. Vertical Termination with Co-linear Flex System c. DV Stove Horizontal Vent Kit d. Dura-Vent Termination Kit.

5) Make gas connections. Refer to the "Gas Connection" section

Test the pilot. Must be as per diagram in the

"Maintenance Instruction" section.

If converting to Propane, make changes

prior see the "Conversion from Natural Gas to Propane" section.

6) Test Gas Pressure. Refer to the "Gas Pipe Pressure Testing" section.

7) Install standard and optional features. Refer to the following sections where applicable:

a. Brick Panels b. Log Set Installation c. Wall Thermostat d. Remote Control e. Optional Side Shelves

8) Final check. Refer to the "Final Check" section.

Before leaving this unit with the customer,

the installer must ensure that the appliance is ﬁ ring correctly and operation fully

explained to customer.

This includes:

1) Clocking the appliance to ensure the correct

ﬁ ring rate (rate noted on label) after burning appliance for 15 minutes.

2) If required, adjusting the primary air to ensure that the ﬂ ame does not carbon. First allow the unit to burn for 15-20 min. to stabilize.

CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer.

CLEARANCES TO

COMBUSTIBLES

The clearances listed are MINIMUM distances. Measure the clearance to both the appliance and the chimney connector. The farthest

distance is correct if the two clearances do not coincide.

For example, if the appliance is set as indicated in one of the ﬁ gures but the connector is too close, move the stove until the correct clearance to the connector is obtained.

This appliance may be installed only with the clearances as shown in the situations pictured.

Do not combine clearances from one type of installation with another in order to achieve closer clearances.

This unit can be installed on a solid combustible surface like a wood ﬂ oor. This unit can also be installed directly on carpeting or vinyl.

Use the minimum clearances shown in the diagrams below:

H35-NG2 & H35-LP2 Clearances

A Side Wall to Unit 6-1/2" / 165 mm B Back Wall to Unit 6" / 152 mm C Vertical Vent Pipe to Back Wall 2" / 50 mm E Unit Corner to Wall 2" / 50 mm Unit Top to Alcove Ceiling 36" / 914 mm

Minimum ceiling height is 36" /914 mm from top of unit.

a. Clearances to combustibles b. Locating Your Gas Stove c. For venting requirements, see "Venting

Hampton® H35-2 Direct Vent Freestanding Gas Stove

INSTALLATION

LOCATING YOUR

GAS STOVE

When selecting a location for your stove, ensure that the clearances listed above are met as well as ensuring that there is adequate accessibility for servicing and proper operation.

A) Cross Corner B) Room Divider C) Island D) Flat on Wall E) Flat on Wall Corner F) Flush with Wall/Alcove

For Vent Termination requirements, see the "Exterior Vent Terminal Locations" section.

MANUFACTURED

MOBILE HOME

ADDITIONAL

REQUIREMENTS

1) Ensure that structural members are not cut

or weakened during installation.

2) Ensure proper grounding using the #8 ground lug provided.

OPTIONAL FAN INSTALLATION

Fan Kit Contains:

Qty. Description

1 Fan Speed Controller with nut, and

knob.

1 Fan Assembly c/w green wire

attached 1 Power cord 1 Plastic locking grommet

1) Remove the Top Control Panel Assembly

by removing the three screws. Diagram 1.

Diagram 1

2) Remove the nylon hole plug from the control

panel.

3) Install the fan speed controller onto the

control panel and secure with nut. Connect

remaining wire harness wires to speed

control. NOTE: Speed control wires must

be in the down position when control panel

is in place.

4) Push black knob onto speed control.

5) Remove the rear access panel on the back

of the stove by removing the 6 screws. Install

the fan onto pins as per Diagram 2.

7) Install locking grommet to power cord and push through hole in the rear panel and give a 1/4 turn to secure.

NOTE: When running wires, keep them clear

of valve assembly and tubing to avoid tangling of wires and valve.

NOTE: Be careful not to cut wires when pass-

ing through holes in the ﬁ rebox.

8) Run green ground wire from fan and connect

to grounding lug.

9) Connect green power cord ground wire to grounding lug.

10) Run the neutral black wire from power cord and connect to fan motor.

11) Run the live black wire from power cord and connect to speed control wire.

12) Connect the white wire of the wire harness to the fan terminal.

NOTE: Pull excess wire next to fan to

avoid excessive heat from the ﬁ rebox.

13) Ensure all wires are pulled away from ﬁ rebox

to avoid excessive heat and secure with stick-on wire clip.

3) Appliance must be anchored to the ﬂ oor with the supplied anchoring methods.

COMBUSTION AND

VENTILA TION AIR

The combustion air from this appliance is drawn from outside the building through the outer ﬂ ue.

Extra provision for combustion air inside the room is not required.

8 Hampton® H35-2 Direct Vent Freestanding Gas Stove

Diagram 2

NOTE: Do NOT damage, cut or remove

the 3" aluminum air intake pipes.

Hint for pushing fan down onto pins - rub a

bit of dish soap on the pins so the grommets will slide down more easily. Check to make sure the fan is seated properly on the pins

- try to move the fan back and forth.

6) Push power cord through hole in the rear panel 14" - 16" and tie a loose knot in the cord on the inside to prevent the power cord from being pulled out. Diagram 2.

14) Re-attach control panel with 3 screws, reversing step 1. Re-attach rear access panel with 6 screws, reversing step 5.

NOTE: When power cord is plugged in, speed control is in the ON position and stove is burning, allow 10 - 15 minutes for the thermodisc (temperature switch) to activate and turn on the Fan automatically.

WARNING: Electrical Grounding Instructions This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

INSTALLATION

PRECAUTIONS

These venting systems are engineered products that have been designed and tested for use with the H35-NG2, and H35-LP2. The warranty will be voided and serious ﬁ re, health or other safety hazards may result from any of the following actions:

1) Installation of any damaged Direct Vent component

2) Unauthorized modiﬁ cation of the Direct Vent System

3) Installation of any component part not

approved by FPI - Fireplace Products International Ltd.

4) Installation other than as instructed by the approved rigid pipe manufacturers and FPI Fireplace Products International Ltd.

Warning: Always maintain required clearances (air spaces) to nearby combustibles to prevent a fire hazard. Do not ﬁ ll air spaces with insulation.

Be sure to check the vent termination clearance requirements from decks, windows, sofﬁ ts, gas regulators, air supply inlets and public walkways as speciﬁ ed in the "Exterior Vent Terminal Locations" section and in your local building codes.

The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or gas-burning appliance. Each direct vent gas appliance must use

it's own separate vent system. Common vent systems are prohibited.

VENTING

INTRODUCTION

The Horizontal Termination Kit and the rigid pipe venting systems, in combination with the Direct Vent Freestanding Gas Stoves, H35-NG2 and H35-LP2, have been tested and listed as direct vent heater systems by Warnock Hersey .

These units use the "balanced ﬂ ue" technology Co-Axial system. The inner liner vents products of combustion to the outside while the outer pipe draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air up the chimney.

Note: These ﬂ ue pipes must not be connected to any other appliance.

The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited.

IMPORTANT

Read all instructions carefully before starting the installation. Failure to follow these instructions may create a ﬁ re or other safety hazard, and will void the warranty. Be sure to check the venting and clearance to combustible requirements. Consult your local building codes before beginning installation.

The location of the termination cap must conform to the requirements in the "Exterior Vent T erminal Locations" section.

VENT RESTRICTOR

POSITION

Vent restriction is required for certain venting installations, see the diagrams in "Venting Arrangement" section to determine if they are required for your installation.

To set the Vent restriction as indicated in the diagrams in the "Venting Arrangement" section, simply loosen the screws and push the vent restrictor plate to the correct position. Tighten the screws.

Horizontal Termination:

Vent Restrictor setting at 36,000 Btu/h

Vertical Termination:

Vent Restrictor setting at 36,000 Btu/h

SAFETY PRECAUTIONS

FOR THE INSTALLER

1) Wear gloves and safety glasses for protec-

tion.

2) Exercise extreme caution when using ladders or on roof tops.

3) Be aware of electrical wiring locations in walls and ceilings.

Hampton® H35-2 Direct Vent Freestanding Gas Stove

INSTALLATION

EXTERIOR VENT TERMINAL LOCATIONS

Minimum Clearance Requirements

A Clearance above grade, veranda, porch, deck, or balcony 12"(30cm) 12"(30cm)

B Clearance to window or door that may be opened 12"(30cm) 9" (23cm)

C Clearance to permanently closed window **

D Vertical clearance to ventilated sofﬁ t located above the terminal within a horizontal distance of 2 feet (61cm)

from the center line of the terminal (check with the local code)

E Clearance to unventilated sofﬁ t 12"(30cm) 12"(30cm)

F Clearance to outside corner: with AstroCap and Vent Riser Termination Caps 6"(15cm) 6"(15cm)

Clearance to outside corner: with all other approved Termination Caps 12"(30cm) 12"(30cm)

G Clearance to inside corner: with AstroCap and Vent Riser Termination Caps 6"(15cm) 6"(15cm)

Clearance to inside corner: with all other approved Termination Caps 12"(30cm) 12"(30cm)

H Clearance to each side of center line extended above meter/regulator assembly 36"(90cm)

J Clearance to service regulator vent outlet 36"(90cm) *

K Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance 12"(30cm) 9" (23cm)

L Clearance to a mechanical air supply inlet

#3' (91cm) above if within 10' (3m) horizontally.

M Clearance above paved sidewalk or a paved driveway located on public property 84"(2.1m)

N Clearance under veranda, porch, deck, or balcony 12"(30cm)

In accordance with current CSA B149.1, Natural Gas and Propane Installation Code

In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code

┼

A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.

‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the ﬂ oor

Clearance in accordance with local installation codes and the requirements of the gas supplier

3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly

3 feet (91cm) above - if within 10 feet (3m) horizontally

Canada

22"(56cm) 22"(56cm)

72"(1.8m) 36"(90cm)

┼

‡

USA

10 Hampton® H35-2 Direct Vent Freestanding Gas Stove

INSTALLATION

4” X 6-5/8” RIGID PIPE

CROSS REFERENCE CHART ONLY

Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI.

Description

6” Pipe Length-Galvanized 46DVA-06 4DT-6 N/A 4D6 SV4L6 TC-4DL6

6” Pipe Length-Black 46DVA-06B 4DT-6B N/A 4D6B SV4LB6 TC-4DL6B

7” Pipe Length-Galvanized N/A N/A 4D7 N/A N/A N/A

7” Pipe Length-Black N/A N/A 4D7B N/A N/A N/A

9” Pipe Length-Galvanized 46DVA-09 4DT-9 N/A N/A N/A N/A

9” Pipe Length-Black 46DVA-09B 4DT-9B N/A N/A N/A N/A

12” Pipe Length-Galvanized 46DVA-12 4DT-12 4D12 4D12 SV4L12 TC-4DL1

12” Pipe Length-Black 46DVA-12B 4DT-12B 4D12B 4D12B SV4LB12 TC-4DL1B

18” Pipe Length-Galvanized 46DVA-18 4DT-18 4D18 4D18 SV4LA TC-4DL18

18” Pipe Length-Black 46DVA-18B 4DT-18B 4D18B 4D18B SV4LA TC-4DL18B

24” Pipe Length-Galvanized 46DVA-24 4DT-24 4D24 4D24 SV4L24 TC-4DL2

24” Pipe Length-Black 46DVA-24B 4DT-24B 4D24B 4D24B SV4LB24 TC-4DL2B

36” Pipe Length-Galvanized 46DVA-36 4DT-36 4D36 4D36 SV4L36 TC-4DL3

36” Pipe Length-Black 46DVA-36B 4DT-36B 4D36B 4D36B SV4LB36 TC-4DL3B

48” Pipe Length-Galvanized 46DVA-48 4DT-48 4D48 4D48 SV4L48 TC-4DL4

48” Pipe Length-Black 46DVA-48B 4DT-48B 4D48B 4D48B SV4LB48 TC-4DL4B

60” Pipe Length-Galvanized 46DVA-60 4DT-60 N/A N/A N/A N/A

60” Pipe Length-Black 46DVA-60B 4DT-60B N/A N/A N/A N/A

Adjustable Length 3”-10”-Galvanized N/A N/A N/A 4DAL N/A TC-4DLT

Adjustable Length 3”-10”-Black N/A N/A N/A 4DALB N/A TC-4DLTB

Adjustable Length 7”-Galvanized N/A N/A 4D7A N/A N/A N/A

Adjustable Length 7”-Black N/A N/A 4D7AB N/A N/A N/A

Extension Pipe 8-1/2”-Galvanized 46DVA-08A N/A N/A N/A N/A N/A

Extension Pipe 8-1/2”-Black 46DVA-08AB N/A N/A N/A N/A N/A

Adjustable Length 12”-Galvanized N/A N/A 4D12A N/A SV4LA12 N/A

Adjustable Length 12”-Black N/A N/A 4D12A N/A SV4LBA12 N/A

Extension Pipe 16”-Galvanized 46DVA-16A N/A N/A N/A N/A N/A

Extension Pipe 16”-Black 46DVA-16AB N/A N/A N/A N/A N/A

Simpson

Direct Vent Pro

Selkirk

Direct Temp™

American Metal

Products®

Amerivent Direct

Metal-Fab™

Sure Seal

Security

Secure- Vent®

ICC Excel

Direct

45º Elbow-Galvanized 46DVA-E45 4DT-EL45 4D45L N/A N/A TE-4DE45

45º Elbow-Black 46DVA-E45B 4DT-EL45B 4DT-EL45B N/A N/A TE-4DE45B

45º Elbow Swivel-Galvanized See 46DVA-E45 N/A N/A 4D45L SV4E45 N/A

45º Elbow Swivel-Black See 46DVA-E45B N/A N/A 4D45LB SV4EB45 N/A

90º Elbow-Galvanized 46DVA-E90 4DT-EL90S 4DT-EL90S N/A N/A TE-4DE90

90º Elbow-Black 46DVA-E90B 4DT-EL90SB 4DT-EL90SB N/A SV4EBR90-1 TE-4DE90B

90º Elbow, Swivel-Galvanized See 46DVA-E90 N/A N/A 4D90L SV4E90-1 N/A

90º Elbow, Swivel-Black See 46DVA-E90B N/A N/A 4D90LB SV4EB90-1 N/A

90º Starter Elbow, Swivel-Galvanized N/A N/A N/A 4D90A N/A N/A

Adaptor* N/A N/A N/A 4D90L N/A N/A

Ceiling Support N/A 4DT-CS 4DFSP 4DSP SV4SD TE-4DE45

Cathedral Support Box 46DVA-CS 4DT-CSS 4DRSB 4DRS SV4CSB TE-4DE45B

Wall Support/Band 46DVA-WS 4DT-WS/B 4DWS 4DWS SV4BM N/A

Offset Support

Wall Thimble-Black 46DVA-WT 4DT-WT 4DWT 4DWT SV4RSM TE-4DE90

Wall Thimble Support/Ceiling Support 46DVA-DC N/A N/A N/A SV4PF TE-4DE90B

Firestop Spacer 46DVA-FS 4DT-FS 4DFSP 4DFS SV4BF N/A

Trim Plate-Black N/A 4DT-TP 4DFPB 4DCP SV4LA N/A

46DVA-ES (N/A - FPI)

Hampton® H35-2 Direct Vent Freestanding Gas Stove

4DT-OS N/A N/A SV4SU N/A

INSTALLATION

Description

Attic Insulation Shield 12” 46DVA-IS N/A@ FPI N/A 4DAIS12 N/A SV4RSA N/A

Attic Insulation Shield -

Basic Horizontal Termination Kit (A) Disc. 4DT-HKA 4DHTK2 4DHTKA SV-SHK N/A

Horizontal Termination Kit (B) 46DVA-KHA

Vertical Termination Kit Disc. 4DT-VKC 4DHTK 4DHTK SV-FK N/A

High Wind Vertical Cap 46DVA-VCH N/A N/A N/A N/A TM-4VT

High Wind Horizontal Cap 46DVA-HC N/A N/A N/A N/A TM-4DHT

Horizontal Square Termination Cap See

Vertical Termination Cap 46DVA-VC 4DT-HVC 4DVC 4DVT SV4CGV-1 TM-4VT

Storm Collar 46DVA-08A 4DT-SC 4DSC 4DSC SV4FC TM-SC

Adjustable Flashing 0/12-6/12 N/A 4DT-ST14 4D12S 4DST14 SV4STC14 TF-4FA

Adjustable Flashing 6/12-12/12 N/A 4DT-ST36 4D36S 4DST36 SV4STC36 TF-4FB

Vinyl Siding Standoff 46DVA-VSS 4DT-VS N/A 4DVS SV4VS TM-VSS

Vinyl Siding Shield Plate N/A 4DT-VSP N/A N/A SV4VS N/A

Snorkel Termination 14” 46DVA-VCH N/A N/A N/A N/A TM-4ST14

Snorkel Termination 36” 46DVA-HC N/A N/A N/A N/A TM-4ST36

Cold Climates 36” N/A N/A 4DAIS12 N/A N/A TM-4AS

Simpson

Direct Vent Pro

(Changed Components)

46DVA-HC 4DT-HHC 4DHC 4DHT SV4CHC-1 TM-4HT

Selkirk

Direct Temp™

4DT-HKB 4DHTK1 4DHTKB SV-HK N/A

American Metal

Products®

Amerivent Direct

Metal-Fab™

Sure Seal

Security

Secure- Vent®

ICC Excel

Direct

Restrictor Disk 46DVA-RD N/A N/A N/A N/A TM-4DS

Extended Vertical Termination Cap 46DVA-VCE N/A N/A N/A N/A N/A

Chimney Conversion Kit A (USA only) 46DVA-KCA N/A N/A N/A N/A TM-4CA6

Chimney Conversion Kit B (USA only) 46DVA-KCB N/A N/A N/A N/A TM-4CA7

Chimney Conversion Kit C (USA only) 46DVA-KCC N/A N/A N/A N/A TM-4CA8

Chimney Conversion Kit Masonry (USA only)

Wall Firestop 46DVA-WFS N/A N/A N/A N/A TM-4TR

Colinear Flex Connectors 46DVA-ADF N/A N/A N/A N/A N/A

FPI

946-506/P Vent Guard (Optional) for AstroCap 946-205 Vinyl Siding Shield for Riser Vent Terminal

510-994 Rigid Pipe Adaptor (Must use with all rigid piping) 946-208/P Vent Guard (Optional) for Riser Vent Terminal

640-530/P Riser Vent Terminal 946-523/P AstroCap Horizontal Cap

Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).

Offset Pipe Selection: Use this table to determine offset pipe lengths.

Pipe Length

(L)

0” (0mm) 4-7/8” (124mm) 13-7/8” (340mm) Simpson Direct Vent Pro: www.duravent.com

6” (152mm) 8” (203mm) 16-1/2” (419mm) Selkirk Direct-Temp: www.selkirkcorp.com

9” (229mm) 10-1/8” (257mm) 18-5/8” (473mm) American Metal Products: www.americanmetalproducts.com

12” (305mm) 12-1/4” (311mm) 20-3/4” (527mm) Metal-Fab Sure Seal: www.mtlfab.com

24” (610mm) 20-5/8” (524mm) 29-1/8” (740mm) Security Secure Vent: www.securitychimneys.com

36” (914mm) 29” (737mm) 37-1/2” (953mm) Industrial Chimney Company: www.icc-rsf.com

48” (1219mm) 37-7/16” (951mm) 45-15/16” (1167mm)

Note: Horizontal runs of vent must be level, or have a 1/4” rise for every 1 foot of run towards the termination. Never allow the vent to run downward - this could cause high temperatures and may present a possible ﬁ re hazard.

4” x 6-5/8” Venting For speciﬁ c instructions on venting components - visit the

Run (X) Rise (Y)

46DVA-KMC N/A N/A N/A N/A N/A

946-206 Vinyl Siding Standoff for AstroCap

manufacturers website listed below.

12 Hampton® H35-2 Direct Vent Freestanding Gas Stove

Alternate

Horizontal

Termination

Caps

INSTALLATION

RIGID PIPE VENTING SYSTEMS

Horizontal or Vertical Terminations

WARNING:

Do not combine venting components from different venting systems.

However use of the the AstroCapTM and FPI Riser is acceptable with all systems.

This product has been evaluated by Intertek for use with Duravent Direct-Vent Pro, Selkirk Direct-Temp, Ameri Vent Direct venting and Security Secure Vent systems.

When using Rigid Vent other than

Simpson Dura-Vent, 3 screws must be

used to secure rigid pipe to adaptor.

The FPI AstroCap American Metal Products Ameri Vent Direct Vent, Security Secure Vent®, Selkirk Direct-Temp. AstroCapTM is a proprietary trademark of FPI Fireplace Products International Ltd. Dura-Vent® and Direct Vent Pro are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.

and FPI Riser Vent terminal are certiﬁ ed for installations using FPI venting systems as well as Simpson Dura-Vent® Direct Vent Pro,

Hampton® H35-2 Direct Vent Freestanding Gas Stove

INSTALLATION

ROTATING 45O ELBOW FOR STRAIGHT HORIZONTAL TERMINATIONS

1) Remove all 4 screws that secure

the elbow to the unit using a 1/4" magnetic nut driver.

Remove all 4 screws

and washers

Horizontal Terminations for All

Venting Systems

The shaded areas in the diagram below show all allowable combinations of vertical runs with horizontal terminations. Maximum one 90O elbow (two 45o elbows equal one 90o elbow). All approved caps listed on page 12 - may be used.

Propane and Natural Gas:

Residential, Manufactured and

Mobile Homes Installations

2) Rotate the elbow 180

3) Secure the elbow by securing

it with the 4 screws.

VENTING ARRANGEMENTS

Vertical Terminations Systems for

Residential Manufactured and Mobile Homes

The shaded area in the diagram below shows all allowable combinations of straight vertical and offset to vertical runs with vertical terminations. Maximum two 45o elbows.

If the vent is ENCLOSED in a chase (min. size 9" x 9") maintain a 1-1/4" clearance to combustibles.

May be installed in Manufactured (Mobile) Homes after ﬁ rst sale.

Offset to Vertical Terminations

The venting arrangements diagrammed below, have a min. of 75% (ﬂ ue loss) efﬁ ciency with Fan Off, as required for manufactured homes. (Actual efﬁ ciency may be as high as 85%)

May be installed in Manufactured (Mobile)

Homes after ﬁ rst sale.

NOTE: See "Vent Restrictor Position" section for installation instructions for the Vent Restrictor Position.

14 Hampton® H35-2 Direct Vent Freestanding Gas Stove

+ 34 hidden pages

HAMPTON BAY H35-NG2, H35-LP2 Owners & Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual