HAMPTON BAY SKU 939-473, 939-473 Instruction Manual

1

INSTRUCTION

MANUAL
LIGHT FIXTURE

Oil Rubbed Bronze Finish

Home Depot SKU 939-473 (UPC008938102704)

2

Thank you for purchasing this Hampton Bay interior light fixture. This product has

Ladder

Safety

Gloves

Flathead

Phillips

Electrical

Wire Bulb

been manufactured with the highest standards of safety and quality.

FEATURES:

1. Uses 120 volt, 60 Watt MAX, standard (A19), incandescent light bulb(s) (not
included).

2. Can be used with any standard, 120 volt, incandescent style dimmer switch.

3. Designed for mounting to ceilings.

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local Home Depot, please call our Customer Service Team at
1-877-527-0313 or visit www.homedepot.com. Please reference SKU 939-473, UPC

008938102704.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: Make sure power is turned off at the electrical panel box before beginning

your installation. Turning the power off at the wall switch is not sufficient to prevent
electrical shock.

INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS

1. Read all instructions prior to beginning the installation process.

2. Do not install this lighting system in or near a wet location.

3. CAUTION: HOT SURFACE. Keep away from curtains and other combustible

materials.

4. THE BULB IS HOT! Make sure that the bulb is cool before re-lamping the fixture.

5. This fixture is intended to be mounted to a 4"square x 2-1/8"deep metal octagon

outlet box. The box must be directly supported by the building structure.

NOTE: All electrical connections must be in accordance with local codes and the
National Electrical Code. If you are unfamiliar with methods of installing electrical
wiring, secure the services of a qualified licensed electrician.

SAVE THESE INSTRUCTIONS

TOOLS REQUIRED FOR ASSEMBLY&INSTALLATION (not included):

Goggles Screwdriver Screwdriver Tape Cutters

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

(2) Screws (3) Wire connectors Tube assembly Diffuser

ASSEMBLY INSTRUCTIONS (AS SHOWN IN DIAGRAM):

1. Make sure the main power to the circuit is OFF.

2. Insert the fixture wires through the threaded stem (with decorative sleeve), securing

stem onto the top section of the fabric shade. Insert the fixture wires up through
the top of canopy, turning to tighten as shown.

3. Secure the longer threaded tube into bottom section of the fabric shade.

4. Install the light bulb – Type A19, 60 Watt Max. CFL bulbs may be used.

5. To install the glass diffuser, remove the decorative cap from the end of the threaded

3

tube. Install the diffuser and tighten with decorative cap. Note: The hex nut can be

1.

Outlet

box

adjusted up and down as needed.

6. Remove the mounting bracket assembly from the canopy and install mounting

bracket to existing outlet box with outlet box screws provided.

7. Make the electrical connections (Required Supply Circuit: 120V 60Hz):

a. Connect the neutral/white wire from the fixture to the neutral/white wire from the

Outlet Box.

b. Connect the live/black wire from the fixture to the live/black wire from the Outlet

Box.

c. Connect the ground wire from the fixture to the ground wire from the Outlet Box.
d. Secure the connections using the wire connectors. Wrap the wire connections with

electrical tape to secure the connections.

e. Place the wires back inside the outlet box.

8. Secure the canopy to the mounting bracket with the canopy screws.

RELAMPING THE LIGHT BULB(S)

1. Turn off the power to the light fixture.

2. Remove the old light bulb(s) and install the new light bulb(s).

3. Restore power to the light fixture.

CAUTION: Refer to the re-lamping label located on the fixture. Do not exceed
recommended wattage.

ASSEMBLY DIAGRAM

1

2. Wire connector

3. Ground (bare) wire

4. Neutral (White) wire

5. Live (Black) wire

6. Ground screw

7. Mounting bracket

8. Outlet box screw

9. Canopy screw

10. Canopy

11. Straight tube

12. Fabric shade

13. Thread tube

14. Bulb (sold separately)

15. Hex nut

16. Flat washer

17. Plastic washer

18. Diffuser

19. Decorative cap

2

6
7

5

4

3

8

9

10
11

12

14

13

15

16
17

19

18

4

Problem

Possible Cause

Corrective Action

TROUBLE SHOOTING:

Light Bulb will not
illuminate.

Fuse blows or circuit
breaker trips when light
bulb is illuminated.

1. Light bulb is burned
out.

2. Power is off. 2. Make sure power supply is

3. Faulty wire connection. 3. Check wiring.

4. Faulty switch. 4. Test or replace switch.
Crossed wires or power
wire is grounding out.

1. Replace light bulb.

on.

Check wire connections.

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture turn the power off to the fixture, use a clean, dry,

or slightly dampened cloth and wipe the shades and the exterior surfaces of the
fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning

off the circuit breaker or by removing the fuse at the fuse box. Next, use a clean,
dry, or slightly dampened cloth and wipe the inside glass and interior surfaces of
the fixture.

3. Allow the fixture to thoroughly dry before restoring power to the fixture.

CAUTION: Do not use any cleaners with chemicals, solvents or harsh abrasives as
damage to components or finish may occur.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and
workmanship for a period of five (5) years from date of purchase. This warranty applies
only to the original consumer purchaser and only to products used in normal use and
service. If this product is found to be defective, the manufacturer’s only obligation, and
your exclusive remedy, is the repair or replacement of the product at the manufacturer’s
discretion, provided that the product has not been damaged through misuse, abuse,
accident, modifications, alterations, neglect or mishandling. This warranty shall not
apply to any product that is found to have been improperly installed, set-up, or used in
any way not in accordance with the instructions supplied with the product. This
warranty shall not apply to a failure of the product as a result of an accident, misuse,
abuse, negligence, alteration, or faulty installation, or any other failure not relating to
faulty material or workmanship. This warranty shall not apply to the finish on any
portion of the product, such as surface and/or weathering, as this is considered normal
wear and tear. The manufacturer does not warrant and specially disclaims any warranty,
whether express or implied, of fitness for a particular purpose, other than the warranty
contained herein. The manufacturer specifically disclaims any liability and shall not be
liable for any consequential or incidental loss or damage, including but not limited to
any labor/expense costs involved in the replacement or repair of said product.