HAMPTON BAY 262, 294, 61-370, 261-568 Instruction Manual

INSTRUCTIONS MANUAL

FOUR LIGHT BATH FIXTURE

HOME DEPOT SKU# 262-294 (UPC# 046335947528)

Page 1

Thank you for purchasing this Hampton Bay Four Light Bath Fixture.
This product has been manufactured with the highest standards of safety
and quality.

FEATURES:

1. For energy savings this fixture has been engineered to safely use a
Self Ballasted Compact Fluorescent Lamp in place of an incandescent
lamp.

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local Home Depot, please call our Customer
Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU (262-294) or UPC (046335947528).

Page 2

CAUTION:

1. Before starting installation of this fixture or removal of a previous
fixture, disconnect the power by turning off the circuit breaker or by
removing the fuse at the fuse box.

2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY
ELECTRICAL QUESTIONS. If you have any non-electrical
questions about this fixture, please call our Customer Service Team at
1-877-527-0313 or visit www.homedepot.com. Please reference your
SKU (262-294) or UPC (046335947528).

3. KEEP your receipt and these Instructions for Proof of Purchase.

TOOLS REQUIRED FOR INSTALLATION AND ASSEMBLY
(not included):

Light Bulb (100

watt maximum or

CFL equivalent)

Safety

goggles

Drill ¼” Drill

bit

Pencil

Level

Phillips

screwdriver

Electrical

tape

Wire

cutters

Wire

strippers

Hammer

Page 3

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

3. Lamp

Socket

4. Socket

Cup

1 ea Main Fixture

Body (#1)

3 ea Glass

Shades (#2)

3 ea Socket

Rings (#5)

ASSEMBLY INSTRUCTIONS:

1. Carefully unpack the fixture. Lay out all parts on a clean surface.

2. Before continuing Assembly please proceed to the Installation Instructions.

3. Slide the Glass Shades (#2) over the Sockets (#3), onto the the Socket Cups (#4).

4. Secure the Glass Shades (#2) to the Socket Cups (#4) using the Socket Rings (#5).

5. Install up to a 100 watt Light Bulb (#22) or Listed SBCFL (Self-Ballasted Compact
Fluorescent Lamp [not provided]) in each Socket (#3) of the Main Fixture Body (#1). Do
not exceed a 100 watt incandescent light bulb, or a 32 watt SBCFL.

Page 4

ASSEMBLY:

22. Light Bulb

5. Socket Ring

2. Shade

1. Main

Fixture Body

3. Lamp Socket

4. Socket Cup

NOTE: This fixture may also be assembled / installed as a downlight, as shown below.

Page 5

PARTS INCLUDED FOR INSTALLATION (parts are not to
scale):

1 ea Wall Plate (#7)

2 ea Wall

Anchors (#9)

2 ea Anchor

Screws (#11)

2 ea Outlet Box

Screws (#12)

3 ea Wire

Nuts (#17)

2 ea Ball Nuts

(#21)

INSTALLATION INSTRUCTIONS:

1. Place the Wall Plate (#7) over the Outlet Box (#6), aligning the mounting slots of the Wall Plate (#7) with the mounting holes
of the Outlet Box (#6), as shown. Use a level to make sure the Wall Plate (#7) is straight.

2. Mark the location of the Keyhole Slots (#8) of the the Wall Plate (#7) onto the wall. Remove the Wall Plate (#7) from the
wall.

3. Drill a ¼” hole at the narrow end of each Keyhole Slot (#8) marking on the wall. Carefully hammer a Wall Anch or (#9 ) into
each Drilled Hole (#10).

4. Replace the Wall Plate (#7) over the Outlet Box (#6), aligning the narrow end of each Keyhole Slot (#8) with its respective
Wall Anchor (#9). Feed the Anchor Screws (#11) through the Keyhole Slots (#8) and thread them into the Wall Anchors (#9)
until the Wall Plate (#7) is flush against the wall. Additionally, feed the Outlet Box Screws (#12) through the mounting slots
of the Wall Plate (#7) and thread them into the mounting holes of the Outlet Box (#6), as shown. Pull the power supply wires
out from the Outlet Box (#6) and through the center hole of the Wall Plate (#7).

5. Attach the Black Supply Wire (#13) to the Black Fixture Wire (#14) and the White Supply Wire (#15) to the White Fixture
Wire (#16) using Wire Nuts (#17). Wrap the Fixture Ground Wire (#18) around the Ground Screw (#23), leaving 3” of wire
extending from the screw. Tighten the Ground Screw (#23). Connect the Fixture Ground Wire (#18) and the Supply Ground
Wire (#19) together using a Wire Nut (#17). Wrap all wire connections with electrical tape for a more secure connection.

Note: If you have electrical questions, consult your local electrical code for approved grounding methods.

6. Place the Main Fixture Body (#1) over the Wall Plate (#7), making sure the Wall Plate Screws (#20) feed through the holes of
the Main Fixture Body (#1). Thread the Ball Nuts (#21) onto the W all Plate Screws (#20), tightening them until the Main
Fixture Body (#1) is securely mounted onto the Wall Plat e (#7).

7. Please proceed back to the Assembly Instructions.

8. Installation is complete. Turn on power at the circuit breaker or fuse box. Turn the light switch on to activate the fixture.

Page 6

INSTALLATION:

10.Drilled Hole

9. Wall Anchor

8. Keyhole Slot

11.Anchor Screw

7. Wall Plate

14.Black Fixture Wire

17.Wire Nut

13.Black Supply Wire

6. Outlet Box

19.Supply Ground Wire

15.White Supply Wire

23.Ground Screw

20.Wall Plate
Screw

12.Outlet Box Screw

16.White Fixture Wire

18.Fixture Ground Wire

21.Ball Nut

Page 7

TROUBLESHOOTING:

Possible Cause Corrective Action

Lights will not turn on.

1. Power is off. 1. Make sure power supp ly is on.

2. Faulty switch. 2. Test or r eplace switch.

Bulb w ill not turn on.

Fuse blows or circuit breaker
trips when light is turned on.

1. Bulb is burned out 1. Replace light bulb.

2. Faulty wire connection. 2. Check wiring.

1. Crossed wires or power wire is grounding
out.

1. Check wire connections.

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean
water, never a solvent) to wipe the surface of the fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the
circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly
dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the
fixture.

3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft
cloth to dust or wipe carefully.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a
period of five (5) years from date of purchase. This warranty applies only to the original consumer
purchaser and only to products used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of of the product at
the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse,
accident, modifications, alterations, neglect or mishandling. This warranty shall not apply to any product
that is found to have been improperly installed, set-up, or used in any way not in accordance with the
instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of
an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to
faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product,
such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not

warrant and specially disclaims any warranty, whether expressed or implied, of fitness for a
particular purpose, other than the warranty contained herein. The manufacturer specifically
disclaims any liability and shall not be liable for any consequential or incidental loss or damage,
including but not limited to any labor/expense costs involved in the replacement or repair of said
product.

Page 8