
INSTRUCTIONS MANUAL
FLUORESCENT CEILING FLUSH MOUNT FIXTURE
Page 1
HOME DEPOT SKU# 201-014 (UPC# 046335949782)

Page 2
Thank you for purchasing this Hampton Bay Fluorescent Ceiling Flush
Mount Fixture. This product has been manufactured with the highest
standards of safety and quality.
FEATURES:
Before returning to your local Home Depot, please call our Customer
Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU (201-014) or UPC (046335949782).
QUESTIONS, PROBLEMS, MISSING PARTS:
1. Easy to install.
2. Handsome White finish with Glacier acrylic lens.

Page 3
CAUTION:
1. Before starting installation of this fixture or removal of a previous
fixture, disconnect the power by turning off the circuit breaker or by
removing the fuse at the fuse box.
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY
ELECTRICAL QUESTIONS. If you have any non-electrical
questions about this fixture, please call our Customer Service Team
at 1-877-527-0313 or visit www.homedepot.com. Please reference
your SKU (201-014) or UPC (046335949782).
3. KEEP your receipt and these Instructions for Proof of Purchase.
TOOLS REQUIRED FOR INSTALLATION AND ASSEMBLY
(not included):
Safety
goggles
Wire
strippers
Phillips
screwdriver
Electrical
tape
Wire
cutters
Flathead
screwdriver
2 ea 28 W T5 Fluorescent
Light Bulbs (#2)

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):
ASSEMBLY INSTRUCTIONS:
1 ea Fixture Pan (#1)
1. Carefully unpack the fixture. Lay out all parts on a clean surface.
2. Before continuing Assembly, please proceed to the Installation
Instructions.
3. Insert 28 W T5 Fluorescent Light Bulbs (#2) (not included) into the
provided Lamp Sockets (#3). (Fig. 1)
4. Open the Latches (#4) on the Fixture Pan (#1). Slide the Acrylic
Lens (#5) onto the Fixture Pan (#1). Close the Latches (#4) to secure
the Acrylic Lens (#5) onto the Fixture Pan (#1). (Fig. 2)
1 ea Acrylic Lens (#5)
Page 4

ASSEMBLY:
Page 5
2. Fluorescent Light
Bulb
3. Lamp Socket
1. Fixture Pan
Fig. 1
5. Acrylic Lens
1. Fixture Pan
Fig. 2
4. Latch
4. Latch
4. Latch

PARTS INCLUDED FOR INSTALLATION (parts are not to
scale):
INSTALLATION INSTRUCTIONS:
3 ea Wire Nuts (#10)
4 ea Mounting Screws (#8)
4 ea Ceiling Anchors (#18)
1. Place the Fixture Pan (#1) onto the desired location, centering it over
the Outlet Box (#6). Mark the location of all the Keyhole Slots
(#16).
2. Remove the Fixture Pan (#1) from the Ceiling (#7). Drill
appropriately sized Holes (#17) at the marked keyhole locations.
Insert the Ceiling Anchors (#18) into the Holes (#17). (Fig. 3)
3. Thread the Mounting Screws (#8) halfway into the Ceiling Anchors
(#18). (Fig. 3)
4. Pull the power supply wires out from the Outlet Box (#6). Attach the
Black Supply Wire (#14) to the Black Fixture Wire (#15) and the
White Supply Wire (#9) to the White Fixture Wire (#11) using Wire
Nuts (#10). Connect the Fixture Ground Wire (#12) and the Supply
Ground Wire (#13) together using a Wire Nut (#10). (Fig. 4) Wrap
all wire connections with electrical tape for a more secure
connection. Note: If you have electrical questions, consult your local
electrical code for approved grounding methods.
Page 6

INSTALLATION INSTRUCTIONS (CONT.):
5. Carefully tuck all wire connections into the Outlet Box (#6). Place
the Fixture Pan (#1) onto the desired location, making sure that the
halfway threaded Mounting Screws (#8) feed through the large
openings of the Keyhole Slots (#16). Slide the Fixture Pan (#1) so
that the Mounting Screws (#8) slide into the narrow slots of the
Keyhole Slots (#16). Tighten the Mounting Screws (#8) down to
secure the Fixture Pan (#1) in place. (Fig. 5 & 5-1)
6. Proceed to Step 3 of the Assembly Instructions.
7. Installation is complete. Turn on power at the circuit breaker or fuse
box. Turn the light switch on to activate the fixture.
Page7