Hammond Manufacturing 1485 Series Catalog Page

1485 Series Lay-In Wireway - NEMA 12

Wireway & Trough

www.hammondmfg.com

Application

• Designed to enclose and protect electrical wiring from dirt, dust, oil and water.

• All sections and ﬁ ttings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.

Standards

• UL 870 Type 1 (unless marked1)

• CSA Type 1 (unless marked1)

• Complies with

Lay-In Wireway

• NEMA Type 12

• JIC EMP-1-1967

• JIC EGP-1-1967

• IEC 60529, IP54

Construction

• Bodies and covers are formed from 14-gauge steel with 10 gauge steel ﬂ anges.

• 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.

• Smooth continuously welded seams.

• Interior surfaces are smooth to prevent wire damage during installation.

• Butt hinged cover is secured with easily operated quick release clamps.

• Oil resistant gaskets are permanently secured.

• Solid oil resistant gaskets are used between ﬂ anges when sections and ﬁ ttings are bolted together.

• One gasket kit, complete with hardware is provided with each straight section or ﬁ tting.

• Sealing plate is supplied.

• Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most ﬁ ttings; see table for exact number.

Finish

• Sections and components are ﬁ nished in ANSI 61 gray powder coating.

Notes

• When joining a wireway section or ﬁ tting to an enclosure be sure to order a box connector.

• When joining two wireway sections, or joining a wireway section to a ﬁ tting, a ﬂ at sealing plate is required at each junction; necessary kits are supplied with each section and ﬁ tting. See table, extra kits may be ordered if necessary.

• When joining a lay-in wireway section or ﬁ tting to a closure plate, a box connector, or cut-off ﬁ tting, an angle sealing plate is required at each junction.

• Necessary kits are supplied with each section and ﬁ tting - see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or ﬁ tting section.

273

Technical references and CAD downloads available at www.hammondmfg.com All dimensions in inches unless speciﬁ ed otherwise

Quality Products. Service Excellence.

www.hammondmfg.com

1485 Series Lay-In Wireway - NEMA 12

Description

Sealing Plates

Supplied

2.5 x 2.5 Part No.

4 x 4 Part No.

6 x 6 Part No.

8 x 8 Part No.

12 x 6

Part No.

6" Section 1 Flat 1485B6 1485C6 1485D6 1485E6 1485F6 12" Section 1 Flat 1485B12 1485C12 1485D12 1485E12 1485F12 24" Section 1 Flat 1485B24 1485C24 1485D24 1485E24 1485F24 36" Section 1 Flat 1485B36 1485C36 1485D36 1485E36 1485F36 48" Section 1 Flat 1485B48 1485C48 1485D48 1485E48 1485F48 60" Section 1 Flat 1485B60 1485C60 1485D60 1485E60 1485F60 120" Section 1 Flat 1485B120 1485C120 1485D120 1485E120 1485F120 60" Long Partition (Barrier) — — 1487CB60

1487DB60

1487EB60

1487DB60 1" Nipple 1 Flat 1485BM1 1485CM1 1485DM1 — — 2" Nipple 1 Flat 1485BM2 1485CM2 1485DM2 — — 3" Nipple 1 Flat 1485BM3 1485CM3 1485DM3 — — Box Entry Swivel Nipple 1 Angle 1485BV1 1485CV1 1485DV1 1485EV1 — Standard Swivel Nipple 2 Angle 1485BV2 1485CV2 1485DV2 1485EV2 — 12" Transposition Clockwise 1 Flat 1485BZ12 1485CZ12 1485DZ12 1485EZ12 — 12" Transposition Counter-Clockwise 1 Flat 1485BZC12 1485CZC12 1485DZC12 1485EZC12 — Flexible Fitting None 1485BFF 1485CFF 1485DFF 1485EFF — Adjustable Fitting 1 Spec. 1485BX Cut-Off Fitting Lay-In 1 Flat 1485BW1 Cut-Off Fitting Non Lay-In 1 Angle 1485BW2

1485CX 1485CW1 1485CW2

1485DX 1485DW1 1485DW2

1485EX 1485EW1 1485EW2

1485FX

1485FW1

1485FW2 90° Elbow, Top Opening 1 Flat 1485B9N 1485C9N 1485D9N 1485E9N 1485F9N 90° Elbow, Inside Opening 1 Flat 1485B9P 1485C9P 1485D9P 1485E9P 1485F9P 90° Elbow, Outside Opening 1 Flat 1485B9Q 1485C9Q 1485D9Q 1485E9Q 1485F9Q 45° Elbow, Top Opening 1 Flat 1485B4N 1485C4N 1485D4N 1485E4N 1485F4N 45° Elbow, Inside Opening 1 Flat 1485B4P 1485C4P 1485D4P 1485E4P — 45° Elbow, Outside Opening 1 Flat 1485B4Q 1485C4Q 1485D4Q 1485E4Q — Tee Fitting, Top Opening 2 Flat 1485BTN 1485CTN 1485DTN 1485ETN 1485FTN Tee Fitting, Outside & Top Opening 2 Flat 1485BTQ 1485CTQ 1485DTQ 1485ETQ — Cross Fitting 3 Flat 1485BY 1485CY 1485DY 1485EY 1485FY Reducer 4 x 4 to 2.5 x 2.5 None — 1485CRE — — — Reducer 6 x 6 to 4 x 4 None — — 1485DRE — — Reducer 8 x 8 to 6 x 6 None — — — 1485ERE — Reducer 12 x 6 to 4 x 4 None ————1485FREC Reducer 12 x 6 to 6 x 6 None ———— Junction Box 1 Flat 1485BJ 1485CJ 1485DJ 1485EJ — Box Connector 1 Angle 1485BK Drop Hanger None 1485BL1 Bracket Hanger None 1485BL2 Cover Plate 1 Angle 1485BH Snap On Flat Sealing Plate None 1485BSM Angle Sealing Plate None 1485BS9

Does not meet CSA or UL requirements

Maintains ratings on CSA and UL approved wireway

1485CK 1485CL1 1485CL2 1485CH 1485CSM 1485CS9

1485DK 1485DL1 1485DL2 1485DH 1485DSM 1485DS9

1485EK 1485EL1 1485EL2 1485EH 1485ESM 1485ES9

1485FRED

1485FK

—

1485FH

1485FSM

1485FS9

Wireway & Trough

Lay-In Wireway

Technical references and CAD downloads available at www.hammondmfg.com All dimensions in inches unless speciﬁ ed otherwise

Quality Products. Service Excellence.

274

1485 Series Lay-In Wireway - NEMA 12

Wireway & Trough

www.hammondmfg.com

Lay-In Wireway

All unmarked diameters are 0.28 All unmarked radii are 0.38

Technical references and CAD downloads available at www.hammondmfg.com All dimensions in inches unless speciﬁ ed otherwise

275

Quality Products. Service Excellence.

+ 5 hidden pages