Hammond XLK5 User manual

English

Open Here

Page 9

*# 1

Model::.-

Congratulations on your purchase of a new Hammond instrument.

Te XLK-5 is intended to be used as a Lower Keyboard for the model XK-5 Drawbar Keyboard.

Please take a moment to review this manual thoroughly in order to familiarize yourself with the features of this keyboard as well as the installation procedures. Keep this manual for future reference.

Owner’s Manual

2	IMPORTANT SAFETY INSTRUCTIONS

Before using this unit, please read the following Safety instructions, and adhere to them.

Keep this manual close by for easy reference.

In this manual, the degrees of danger are classifed and explained as follows:

Tis sign shows there is a risk of death or severe injury if this unit is not properly used as instructed.

	Do not open (or modify in any way) the unit.	Do not allow any objects (e.g., fammable material,
	Do not attempt to repair the unit, or replace parts in	coins, pins); or liquids of any kind (water, soft drinks,
	Do not attempt to repair the unit, or replace parts in	etc.) to penetrate the unit.
	it. Refer all servicing to your retailer, the nearest Ham-	etc.) to penetrate the unit.
	it. Refer all servicing to your retailer, the nearest Ham-

mond Dealer, or an authorized Hammond distributor, as listed on the “Service” page.

Never use or store the unit in places that are:

Subject to temperature extremes (e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heat generating equipment)

Damp (e.g., baths, washrooms, on wet foors)

Humid

Exposed to rain

Dusty

Subject to high levels of vibration

Use only with the cart, stand, tripod, bracket, or table specifed by the manufacturer, or sold with the apparatus. When cart is used: use caution when moving the cart/apparatus combination to avoid injury from tipover.

Immediately turn the power of, remove the AC cable from the outlet, and request servicing by your retailer, the nearest Hammond Dealer, or an authorized Hammond distributor, as listed on the “Service” page when:

Te AC adaptor, the power-supply cord, or the plug has been damaged; or

If smoke or unusual odor occurs

Objects have fallen into, or liquid has been spilled onto the unit; or

Te unit has been exposed to rain (or otherwise has become wet); or

Te unit does not appear to operate normally or exhibits a marked change in performance.

In households with small children, an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit.

Protect the unit from strong impact. (Do not drop it!)

Tis sign shows there is a risk of injury or material damage if this unit is not properly used as instructed.

*Material damage here means a damage to the room, furniture or animals or pets.

Never climb on top of, nor place heavy objects on the unit.

Before moving the unit, disconnect the AC adaptor and all cords coming from external devices.

Be sure to grasp the plug when unplugging it from the unit. Pulling on the cord can damage it, and create the danger of fre and electrical shock.

Turn of all devices before hook up. Follow all instructions and use only designated cables.

Make sure not to pinch your fngers when you assemble or disassemble this unit.

In case in the future your instrument gets too old to play/use or malfunctions beyond repair, please observe the instructions of this mark, or, if any question, be sure to contact your dealer or your nearest town or municipal ofce for its proper disposal.

*# 1 :.- Owner’s Manual

NAMES AND FUNCTIONS	3

				5


			CU-1


		2	Upstream	4	Downstream
	0		Upstream		Downstream
	0
	1	3			Downstream side
	1	3			<![if ! IE]> <![endif]>B$75
					<![if ! IE]> <![endif]>B$75
LOWER MANUAL			CU-1 JACK

Square-front (“waterfall”-style) virtual multi-contact keys, 61		Use to connect a CU-1 Leslie Mode Switch.
notes.	CU-1 MOUNTING HOLE
PRESET KEYS		Tree (3) mounting holes are provided to allow the CU-1 to be
Selects the Patch or Favorite of the Lower part. 9 Preset Keys		mounted in two diferent locations.
plus Cancel, 2 Preset Keys for adjusting Drawbar settings.	0	HOLE CAP (2pcs)
POWER LAMP		Use these to plug the screw holes on the rear of the XK-5 Key-
Indicates when the power is “ON.”		board (see page 5).
SIDE PANELS	1	KNOB BOLT (4pcs)
Use these decorative side panels to help secure the XK-5 Draw-		M6 x 15mm.
bar Keyboard on either side.	2	RUBBER FOOT (4pcs)
SIDE BRACKET		Use these if you wish to mount the XLK-5 to an ST-XLK3
Place the XK-5 Keyboard on top of these brackets.		Keyboard Stand.
H-BUS FROM ORGAN JACK	3	TAPPING SCREW (4pcs)
Use a proprietary Hammond B $75 cable to connect the		ø4 x 12mm. Use these to attach the rubber feet described above
XK-5 Keyboard to the XLK-5. Te cable will supply both DC		to mount the XLK-5 to an ST-XLK3 Keyboard Stand.
power and data from/to the XK-5.	4	H-BUS CABLE
H-BUS TO PEDAL JACK		25cm. Use with sticking B $75 label.
Use a proprietary Hammond B $75 cable to connect the	5	PROTECTIVE SHEET (2pcs)
XLK-5 an EXP-250 Expression Pedal or an XPK-250W Pedal		Use these to protect the inside of the panels from the faw dur-
Clavier.
Clavier.		ing attaching the XK-5.
		ing attaching the XK-5.

		*# 1 :.-

4	ASSEMBLY PROCEDURE

Do this assembly carefully to avoid injury to hands or feet.

Disconnect the power cable before this procedure.

DO THIS FIRST:

If you are using the XLK-5 Keyboard with the ST-XLK3 stand, attach the rubber feet using the tapping screws (parts 2and 3on page 3) as shown on the left. Use a #2 Phillips screwdriver.

	Using with ST-XLK3
1	2

Assemble the keyboard stand (ex. ST-XLK5W).

Carefully place the XLK-5 on the stand as shown.

Connect the two B $75 cables and the CU-1 cable as shown above. Use the clamps inside the panels to secure the cables.

*# 1 :.- Owner’s Manual

Carefully place the XK-5 Keyboard on a towel or other soft surface to avoid damage, then remove the 6 screws (for rear, “B” 2 - M4 x 16, for bottom, “A” 4 - ø4 x 10) shown on the

left using a #2 Phillips screwdriver.

Insert the hole caps into the two holes on the rear panel.