Hammerton Studio GCCL2086 Owner Manual

Included Components

Assembly Instrucons

Step 6: Aach glass to braided fabric cord.
If Gem or Hedra Pendant:

Tighten set screws to hold glass in place.

If Parallel Glass Pendant:

Install glass panels by
unscrewing the cylinder knobs

unl glass can be slid into housing.

Note that the cylinder knobs do
not have to be fully removed from
the xture to install glass panels.
Tighten the cylinder knobs,
ensuring that the all thread passes
through the glass panels.

If Ledgestone Glass Pendant:

Use #8-32 nylon p set screws
to retain blown glass.

If Axis Pendant:

Slide glass along retenon screws
using slot in glass. Slide pendant

cover over glass and ghten nial

unl snug.

Blossom Pendant:

Screw glass element into

threaded pendant housing

A. Hardware Packet R, with Instrucons

B. Glass Gems (QTY:9)

C. Canopy
D. Braided Fabric Cord (QTY:9)
E. Cord grip (QTY:9 — Aached to canopy)
F. Set Screws (QTY: 18)
G. Cylinder Knobs (QTY:4)

Step 3: Make Wire Connecons to each of the drivers, mounted
inside of the canopy. Using the three installed terminal blocks
make the following connecons. Remove protecve covers
from terminal blocks by removing the two screws from one
side. Each driver will be wired in series with 3 pendants.
Braided fabric cord must be wired to the Driver, Black to Black
and White to Red. Make wire connecons from driver to
supply. White to white, black to black, and ground the xture to
the canopy.

WARNING

DO NOT DIRECTLY CONNECT LEDs TO AC

POWER. LEDs will be damaged if exposed to high voltages.

The LED’s must be wired in series to work properly.

1. Allen Key (provided)

2. Philips screw driver (not provided)

3. Wire cuers/strippers (not provided)

4. Measuring tape (not provided)

Required Tools

Step 1: Feed the braided fabric cord into the canopy unl the

desired amount of cord is le between the canopy and light
body. Take into account that a minimum of 6” of cord will be
required for connecng the wiring to the driver.

Step 2: Use the measuring tape to be sure that all of your light
body is hanging the proper distance from the canopy. Tighten
the cord grip using a at blade screw driver. The cord grip is on
the face of the canopy. DO NOT OVER TIGHTEN. THIS MAY
DAMAGE THE FIXTURE.

Canopy

Braided
Fabric
Cord

Blown Glass
(Gem shown)

Step 4: Mount the canopy to the ceiling
using the provided Mounng

Instrucons.

EBR020U-0500-32 :

Step 5: Aach face plate to canopy using
cylinder knobs. Glass should not be
installed on cords.

Canopy

Braided
Fabric
Cord

Parallel

Glass

Panel

Parallel

Pendant

Blown Glass Pendant

Axis

Pendant

Ledgestone

Pendant

Blossom

Nebula

Nebula Pendant: Screw inner glass

into socket. Un-Screw Glass Retenon
nut. Raise the Top Glass Retenon Cap
up the stem. Slide Glass Shade over
inner glass, lt to the side of the glass
allowing the Boom Glass Retenon to
slip inside the Glass Shade, slide the rest
of the Boom Glass Retenon the rest
of the way into the Glass Shade, Allow
the Glass to sit on the top of the lips of
the Boom Glass Retenon. The open­ing of the Glass Shade may vary and will
not be a perfect circle. Ensure that the
Boom Glass Retenon is rotated so
that the maximum amount of Glass
surface area is resng on the lips. Lower
the Top Glass Retenon Cap, center the
xture on the Boom Glass Retenon

and Secure Retenon Nut. (NOTE: Tight-

en ll Snug. DO NOT Overghten!)

LED 1 Black

LED 2 Black

LED 3 Black

Driver Red LED 1 White

Driver Black

LED 2 White

LED 3 White

LED 4 Black

LED 5 Black

LED 6 Black

Driver Red LED 4 White

Driver Black

LED 5 White

LED 6 White

LED 7 Black

LED 8 Black

LED 9 Black

Driver Red LED 7 White

Driver Black

LED 8 White

LED 9 White

Raindrop

If Raindrop Glass Pendant:

Install blown glass by raising
cover to expose the electrical
assembly at the end of the
braided cord. Place frosted

diffuser in glass mount, frost-

ed side down, and screw the
glass assembly onto the
threaded LED mount. Tight­en with wrench. Next, lower
cover back over glass and
screw to tighten down.

(NOTE: Tighten cover ll
Snug. DO NOT Overghten!)

Blossom

CHB0059-09

WARNING: FAILURE TO INSTALL THIS FIXTURE

PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE.

It is recommended that this product be installed by

a licensed electrician who is familiar with proper

LED installaon and electrical loads.

Rock Crystal
CHB0050-09

Axis

CHB0060-09

Assembly Instrucons

CHB0039-09, CHB0042-09, CHB0045-09,
CHB0049-09, CHB0050-09, CHB0056-09,
CHB0060-09, CHB0066-09, CHB0067-09,

CHB0068-09, CHB0069-09, CHB0078-09

Warranty

About Hammerton Studio

41-001-00020

Rev 13

Gem

CHB0039-09

Parallel

CHB0042-09

Aalto

CHB0049-09

Ledgestone

CHB0056-09

Hedra

CHB0045-09

Nebula

CHB0066-09

Raindrop

CHB0078-09

ONE YEAR LIMITED WARRANTY

Hammerton, Inc. (Hammerton) warrants the original owner that
this product will be free of defects in material or workmanship for
the period of one year from the date of original purchase from
Hammerton, if (i) the allegedly defective product has not been
abused, misused or improperly maintained and or repaired during
the warranty period, (ii) the defect is not caused by water
damage/flooding, fire, explosion, earthquakes or similar
phenomenon, and (iii) the defect is not caused by improper
installation (unless installed by Hammerton).
In order to obtain warranty service, the user must first complete
a warranty claims form. Hammerton will determine if the product
will be inspected on site or returned to Hammerton. If after the
inspection Hammerton finds that the product is defective as
claimed, Hammerton will, at its option, repair or replace the
product free of charge, or Hammerton may also agree to
outsource necessary repair work locally using local contracted
labor. Prior to any outsourcing of repair work regarding this
fixture, a Work Authorization Form must be signed by both the
client and Hammerton Representative. Failure to do so may result
in a denial of reimbursement. Hammerton warrants any replaced
or repaired products for ninety days after shipment or through
the end of the original warranty period, whichever is longer. All
products or parts that are replaced become the property of
Hammerton.
No representative or employee of Hammerton is authorized to
make any modification or addition to this limited warranty.

TO THE FULL EXTENT ALLOWED BY LAW, THE FOREGOING
WARRANTY AND REMEDIES ARE EXCLUSIVE, AND HAMMERTON
EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. TO THE FULL EXTENT ALLOWED BY
LAW, HAMMERTON EXCLUDES AND DISCLAIMS LIABILITY,
WHETHER BASED IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE FOR ANY CONSEQUENTIAL, INDIRECT INCIDENTAL
OR SPECIAL DAMAGES OF ANY NATURE ARISING OUT OF THE
SALE INSTALLATION, MAINTENANCE, USE OR FAILURE OF THIS
PRODUCT, EVEN IF HAMMERTON HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES IN ADVANCE, AND
HAMMERTON LIMITS ITS LIABILITY TO REPLACEMENT, REPAIR
OR REFUND OF THE PURCHASE PRICE PAID, AT HAMMERTON'S
OPTION.)
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION ON
IMPLIED WARRANTY AND INCIDENTAL OR CONSEQUENTIAL
DAMAGES MAT NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS YOU MAY HAVE OTHER RIGHTS,
WHICH VARY FROM STATE TO STATE

HAMMERTON STUDIO

When we introduced the Hammerton Studio brand in 2014, we
saw an enormous opportunity to raise the bar in decorative
lighting. In design, we wanted to lead rather than follow. In

construction, we wanted to showcase Hammerton’s renowned

reverence for time-honored artisan craftsmanship and authentic
materials. In performance, we wanted to provide highly reliable
solutions that far exceeded industry norms for aesthetics,
function, and quality. Based on the brand’s dramatic growth and
customer feedback, it’s clear we are on the right track.

EXTRAORDINARY DESIGN VALUE
IN ARTISAN GLASS & METALWORK

Hammerton began in 1995 as a blacksmith shop, but we’ve come

a long way since then. Today we employ a world class team of
metal artisans who are disciplined in a broad range of fabrication
techniques and processes. We’ve also added in-house capabilities
in blown, cast and kiln-fused glass, and today Hammerton
operates one of the largest artisan glass production facilities in
the U.S. With deep design and fabrication expertise at the

intersection of glass and metalwork, we’re laying the foundation

for a new era of lighting innovation.

THE HAMMERTON HERITAGE

Our Hammerton Studio brand stands on the shoulders of more
than a quarter century of experience pushing the boundaries of
innovative custom lighting design. Each Hammerton Studio
collection has been inspired by custom work our company has
brought to life in collaboration with leading interior design
professionals over the years. Built to your specifications, every
fixture reflects the uncompromising design and attention to detail
that is distinctly Hammerton.

A REPUTATION REFLECTED BY OUR CLIENTS

Hammerton fixtures are as extraordinary as the clients who
purchase them, including Forbes 400 members, Fortune 500
leaders, award-winning entertainers, fashion and interior
designers, sports legends, and leading luxury hospitality brands.

Hammerton Inc.

217 Wright Brothers Drive

Salt Lake City, UT 84116

801-973-8095

[e-mail]

www.hammerton.com