USER GUIDE
hammerheadvac.com/learn
info@hammerheadvac.com
561-451-1112
2
4
5
6
7
8
9
10
11
12
FREQUENTLY ASKED QUESTIONS
BATTERY INSTALLATION AND USE
CORD CARE, MOTOR SAFETY, ANTI-THEFT
PROP AND MOTOR/CORD REMOVAL
SETTING UP THE MOUNT ASSEMBLY
ALL ABOUT DEBRIS BAGS
GENERAL OPERATING PROCEDURE
USING THE HH1062 SMART SWITCH
TROUBLESHOOTING GUIDE
WIRING DIAGRAMS
WARRANTY STATEMENT
14
USER GUIDE 1
hammerheadvac.com/learn
V1.2 2/1/18
1
FREQUENTLY ASKED QUESTIONS
USER GUIDE 2
hammerheadvac.com/learn
V1.2 2/1/18
2
The HAMMER-HEAD gives you maximum vacuuming power in a small, lightweight, portable package. That is what sets our
cleaner apart from conventional vacuum systems. Our 12-volt rechargeable unit has you cleaning immediately without the
usual set-up and run-around.
WHAT WILL IT DO?
Just lower it into the water and turn it on. The patented pressurized motor can entirely recirculate the average pool in under
an hour, and vacuum it clean in under ten minutes. Sand, sticks, leaves, and even coins are pulled into the high capacity
debris bag, reducing the number of filter cleanings. You'll use less effort, too.
WHAT WON'T IT DO?
Hammer-Head units equipped with a standard debris bag can vacuum up large leaves, coarse sand, sticks, mulch, small
gravel and even some coins. With a superfine debris bag (HH1508) or ultra-fine volcano bag (HH1510), you'll be able to pick
up almost all finer silt and dust. It will not filter algae out of the water, and it is not a complete substitute for the pool's
filtration system or filtration vacuuming. There will be cases where the filtration system is the best way to clean the pool. For
all other cases, however, the advantage to using the Hammer-Head is that the debris goes into the bag, it stays out of the
filter system. This means fewer filter cleanings, and less strain on the pool equipment.
WHY WOULD I WANT TO USE ONE?
Hammer-Head can help you increase your profitability. In the pool business, time is definitely money, and the rapid setup
and working speed of the Hammer-Head unit will cut your pool vacuuming time by as much as 50%. If your goal is to shorten
your workday, or if you want to take on more work, you will save time with a Hammer-Head.
What is your time worth to you? In the maintenance business, time really is money, and any tool that saves you time is an
investment in your own profitability. Faster cleaning times means more pools can be serviced in a day, leaving time for repair
work or opening new accounts. Your Hammer-Head will pay for itself in time savings alone and will leave you wondering
how you ever got by without one.
DO I HAVE TO BE TRAINED TO OPERATE IT?
A Hammer-Head isn't that much different than your household vacuum cleaner. The cart is balanced, rolls easily over most
terrain, and carries most of what you need in one trip. You'll expend less energy on the job. Just attach a standard pool pole,
lower it into the water, and turn it on. It's that easy.
IS IT SAFE FOR VINYL LINER POOLS?
Yes. The Hammer-Head vacuum head has over 1" of clearance from the pool bottom, so scuffing or tearing a liner is not an
easy thing to do. And because the Hammer-Head vacuum head design has wheels on the outside of the head, they protect
it from making contact with the liner. The Hammer-Head suction is very powerful, but it can't lift the liner off the bottom
because it's not close enough to it. We also make a brush attachment for the 21" head that lifts the vacuum off the bottom on
firm brush bristles. It will change the steering, but raise the clearance even more.
WHAT IS THE MINIMUM WATER DEPTH?
Hammer-Head cleaners operate in any water depth greater than 12 inches. The debris bag does not have to be fully
submerged for the vacuum to work, but the propeller on the motor must be underwater. Hammer-Head vacuums do not
vacuum on dry land.
IS IT SAFE TO VACUUM WHILE SWIMMERS ARE IN THE WATER?
The Hammer-Head uses safe 12 volt DC power to operate. Although it is easier to vacuum a pool when there are no
swimmers present, there is no electrocution danger to swimmers when the Hammer-Head is battery powered and in use.
HOW DOES IT MOUNT TO MY TRUCK OR TRAILER?
USER GUIDE 3
hammerheadvac.com/learn
V1.2 2/1/18
3
The SERVICE-21 mounts to any truck equipped with a 2" REESE type hitch receiver. It mounts to any trailer with a set of U-bolts
(included). The cart is secured to the mount with a toggle clamp latch and a safety pin. The Resort-30 and Resort-21 units use
different carts and do not mount.
CAN I GET A RESORT-30 UNIT THAT CAN MOUNT?
No, but... Some prefer the larger head and longer cord on the RESORT-30, but need a portable unit for their daily pool route, so we
offer the SERVICE-30 as an alternative. It has the longer cord (60') and larger head (30") and also includes the mount system.
WHAT IS THE DIFFERENCE BETWEEN THE RESORT UNIT AND THE SERVICE UNIT?
The Resort units and Service units both use the same motors and the same interchangeable parts. The main difference between the
two is in the cart design. Our service units are designed for pool to pool service route work and are ready to mount on your truck or
trailer. Resort units are designed for maintenance work where the unit will be left on site, and are not compatible with the vehicle
mount assembly. Resort-30 units have been used by aquatic facility managers around the US and abroad. Disney Resorts, Sea
World, the US ARMY, the YMCA, cruise lines, countless country clubs, condominium associations, and municipalities have relied on
the portability and ease of use that make the Resort-30 and Resort-21 the only economical equipment choice.
IS THERE A WARRANTY? CAN I GET PARTS?
Hammer-Head units are backed by a limited one year warranty (12 months upon registration, or 6 months if the unit is not registered)
and we offer a full compliment of readily available parts through your dealer/distributor, and service through Hammer-Head to keep
your cleaner's motor working smoothly year after year. Click here to download our warranty statement.
CAN I JUST PLUG IT INTO A WALL SOCKET?
NO. The HAMMER-HEAD is designed to accept a 12 volt deep cycle marine battery as a power source (not included), and the use of
any other power source is not advised. Attempting to use any other power source can damage the unit and/or put you at risk of
electric shock. You can use any 12 volt battery of any size, but typically, the bigger the battery, the longer the run time. Deep-cycle
batteries are the only batteries that will last. It is possible to run the Hammer-Head using a 110 volt AC to 12 volt DC converter, we do
not recommend operating the unit in this way due to the higher risk of electrocution. Please call to discuss the necessary
specifications using a converter.
WHAT KIND OF BATTERY AND CHARGER WILL I NEED?
We suggest the use of a 12 volt deep-cycle marine battery and an automatic charger that can charge at a minimum of 6 amps and no
more than 10-12 amps. Charge your battery every day. DO NOT TRICKLE CHARGE. DO NOT USE A CAR BATTERY.
Marine batteries typically come in series sizes 24, 27, and 30. We suggest a series 27 size battery. The bigger the battery, the longer
the run-time. Avoid marine starting batteries. A general purpose trolling motor battery will work fine. We do not recommend using
marine starting or cranking batteries due to their shorter life span. Sealed, or maintenance-free batteries are a good idea so you don't
have to check liquid levels. These items are available at super stores, marine supply stores, auto supply stores, and some buyer's
clubs. Make sure you charge your new battery before using it for the first time. Hammer-Head strongly suggests that you use a deepcycle marine gel battery for the best performance and longest life. For more information about gel batteries and chargers, visit
www.poolandmarine.com
WHAT IS THE NOCO CHARGING PORT FOR?
Hammer-Head units are equipped with a NOCO battery charging port, located just below the switch (NOCO part number GC016 or
Hammer-Head part number HH1902). When using the compatible NOCO charger (NOCO part number G7200 or Hammer-Head part
number HH1900 - not included), you can plug directly into the side of the unit for nightly charging. The NOCO charging port also gives
an LED readout of the battery charge level. TIP: After connecting to the port and plugging the NOCO G7200 charger into an
outlet for the first time, make sure you do the initial setup. Press the "MODE" button to select the proper voltage level
(12volts) and the battery type (in most cases select "NORM", unless you are using an AGM-type marine battery). Once you
have set up the charger, it will charge at the proper rate of 7.2 amps, bring the battery up to a full charge, and then maintain
it until you are ready to work again. Remember, the charger setup only has to be done the first time you use your NOCO
G7200 charger, after that, the charger automatically knows what to do. For best results and longest battery life, make sure your
Hammer-Head unit is always plugged in to your NOCO charger (or an automatic charger with a minimum charge rate of 6
amps) when not in use.
BATTERY USE AND LIABILITY
USER GUIDE 4
hammerheadvac.com/learn
V1.2 2/1/18
4
Thousands of Hammer-Head pool cleaning units are currently in use across the United States and in other parts of
the world. With proper care they will provide years of dependable service. Please review the following safety
information.
WARNING: IMPROPER BATTERY USE OR FAILURE TO INSPECT AND MAINTAIN YOUR 12 VOLT
BATTERY CAN RESULT IN SHORT CIRCUITS, DAMAGE DUE TO OVERHEATING, BATTERY
FAILURE, AND POSSIBLE FIRE OR PERSONAL INJURY.
THE OPERATOR ASSUMES ALL RESPONSIBILITY AND/OR RISK ASSOCIATED WITH THE USE OF
ANY HAMMER-HEAD PRODUCT, INCLUDING BATTERY SELECTION, INSTALLATION, USE, AND
MAINTENANCE. USE OF ANY POWER SOURCE OTHER THAN A 12 VOLT DEEP CYCLE MARINE
BATTERY IS NOT RECOMMENDED AND CAN VOID ALL WARRANTY OR LIABILITY CLAIMS.
• Wiring connections must be inspected daily. Wires that are hot to the touch indicate a connection problem and
should be repaired. Hammer-Head units that are not working properly should be either repaired immediately or
disconnected from all power sources and removed from service.
• Do not place anything in the battery box that can bridge the terminals on the battery - this can cause direct short
circuits and possible fire or even battery explosion.
• If you reverse the positive and negative wire connections on your battery, the motor will run in reverse and the
vacuum will suck the bag into the propeller. (If you have the HH1062 Smart Switch, the switch will not allow the unit
to run if the wires are reversed).
INSTALLING YOUR BATTERY
CORD CARE
USER GUIDE 5
hammerheadvac.com/learn
V1.2 2/1/18
5
• Poor power cord maintenance drastically shortens the
life of the motor assembly. Store the cord in large loops
as shown - Do not wind the cord up tightly.
• Avoid kinking the power cord or sucking it up into the
vacuum head.
• Avoid pinching the power cord in the mount assembly
when mounting the unit on to your vehicle.
• After vacuuming, remove any twists in the cord by
coiling the cord starting from the cart and ending at the
vacuum head. The head can roll across the deck on its
wheels, allowing you to take the twists out by spinning
the vacuum head before you put it on to the cart rest.
HOW CAN I KEEP MY SERVICE UNIT FROM BEING STOLEN?
Unfortunately, theft of Hammer-Head units is on the rise. The
easiest way to secure your cleaning unit is to put a padlock
through the mount ring on the cart frame (as shown here). If the
lock is in place, the cart can't easily be removed from the mount
assembly.
We also suggest using a locking hitch pin. (Hitch pins are not
included with the HH1300 mount assembly or with complete
Service-type cleaning units and cart assemblies.
MOTOR SAFETY & CARE
• Do not run the motor out of the water longer than three minutes.
• Do not attempt to remove or replace the bag or reach into the vacuum head while the motor is running.
• Hammer-Head units are very durable, but it is often better to scoop toys, rocks, sticks, or tree seeds out of the
pool before vacuuming to avoid jamming or breaking the propeller.
• Heavy piles of leaves can sometimes clog the vacuum. One way to clear clogs without stopping is to turn the
unit off and on a few times. (If you have the HH1062 Smart Switch, the motor will do this automatically three
times to clear the obstruction). You can also try raising the vacuum up to the surface and slightly out of the
water. When the vacuum sucks in a little air, it can loosen clogged debris so that it will pass into the bag.
• If the motor stops abruptly while cleaning, turn the unit off as quickly as you can to avoid damaging the unit.
(The HH1062 Smart Switch will prevent the motor from overheating in the event of a propeller jam). Some units
may also be equipped with a 30amp blade-type automotive fuse to prevent a motor overheat. If a motor jam
occurs on a unit equipped with a fuse, the fuse must be replaced before the unit will turn on again. (Spare fuses
can be purchased from any automotive parts supply store.
• Do not open the motor or disconnect the blue power cord from the motor assembly. Doing so voids the warranty
and exposes the motor to water damage.
• Motor/cord assemblies are sold through you dealer as a sealed unit. Damaged motors can also can be rebuilt.
For more information on motor repairs, please download a repair form here: https://www.hammerheadvac.com/
downloads/
• Need help? Please refer to our troubleshooting guide before you call. (The troubleshooting chart is included in
this user guide or you can find one here: https://www.hammerheadvac.com/downloads/
REMOVING AND REINSTALLING THE PROPELLER
USER GUIDE 6
hammerheadvac.com/learn
V1.2 2/1/18
6
Weekly prop debris removal is an
important part of routine cleaner
maintenance. Excess debris can build
up around the prop shaft and
compromise the watertight seal.
Propellers are durable but over time
the leading edge can become rough.
Props can be sharpened with a file to
remove burrs and nicks. This makes
the prop run more smoothly and keeps
debris from snagging on it while you
vacuum. Remove the propeller before
attempting to sharpen it.
REMOVING AND REINSTALLING THE MOTOR/CORD ASSEMBLY
IMPORTANT: DO NOT attempt to remove the cord from the motor, open the black cord nut, or open the motor
in any way. Doing so can void the warranty and compromise the watertight seal.
1.
USER GUIDE 7
hammerheadvac.com/learn
V1.2 2/1/18
7
OPEN
2.
3.
4.
CLAMP LATCH ADJUSTMENT DETAIL
Y
CLAMP LATCH
SAFETY PIN
12”-16”
WARNING!
MOUNTING DEVICE:
CLAMP LATCH MUST BE PUSHED
COMPLETELY FORWARD UNTIL IT
POINTS BEFORE USING THIS
CHECK THESE FOUR SAFETY
LOCKS INTO PLACE AND SPRING POPS
PIN SHOULD MAKE CONTACT WITH
BE TIGHTENED DOWN AND THE BOLT
CART MOUNT LOOP WHEN LATCHING
BOTH NUTS ON THE LATCH BOLT MUST
MOUNT UPRIGHT
12”-16”
IS LOCKED DOWN
CART FRAME MUST MAKE CONTACT
WITH MOUNT CHANNEL WHEN CLAMP
DEVICE COULD LEAD TO
ALWAYS USE THE SAFETY PIN
SERIOUS ACCIDENT OR INJURY
FAILURE TO MAINTAIN OR CHECK THIS
U-BOLT
AND RISK
ASSOCIATED
ASSUMES ALL
THE OPERATOR
RESPONSIBILITY
LOWER U-CHANNEL
WITH THE USE
OF THIS PRODUCT
U-BOLT
ASSEMBL
VEHICLE MOUNT
.
our vehicle (or trailer) must have a 2” hitch
Y
Setting up the Hammer-Head HH1300 MOUNT
If you are not using the hitch adapter for trailer mounting,
then U-bolt the Hammer-Head mount directly to the
trailer wall in an area that can support the total weight
sufficiently (approximately 130-140 lbs). The use of
straps or braces from the vehicle to the top of the
NOTE:
to use the mount assembly
mount upright can provide additional support.
TRAILER MOUNT
WARNING!
WARNING!
Bolt the hitch adapter to the mount upright
using the included u-bolts so that the bottom
of the mount upright will be at least 12-16
inches from the road surface. The cart wheels
should be high enough so that they do not
make contact with steep driveways or speed
bumps. Do not set up with the cart tires rolling
on the road.
The lower u-bolt can be placed under the
lower u-channel if more height is needed
or above it if less height is needed.
INSTRUCTIONS:
WARNING!
HITCH ADAPTER
Make sure to tighten the hardware sufficiently
to avoid slippage.
Check all hardware and mount components
regularly for tightness, corrosion, and wear.
Do not transport your Hammer-Head unit with
chemicals in the accessory tray.
Secure all loose items on your Hammer-Head
unit before driving.
Refer to the clamp latch adjustment detail
(at right) to properly adjust the clamp latch.
Do not use the clamp latch without first adjusting
the fit and checking all four safety points.
Questions? Call 561-278-8992 or email us: info@hammerheadvac.com
V1.2 02/01/18
ATTACHING THE DEBRIS BAG
USER GUIDE 8
hammerheadvac.com/learn
V1.2 2/1/18
8
Hammer-Head bags are all handmade here in the USA from chemical resistant materials and feature a no-slip cleat/
string attachment and color-coded tags for quick identification. They are reusable and with proper care will provide
months of professional service. Bags should be stored clean and dry, and you should avoid dragging or scuffing them
on the pool bottom, the pool deck, coping or any other rough surface. Bags can be punctured by sharp objects such as
twigs, sticks, rocks, or glass. Please use care when vacuuming to prolong the life of your debris bag. Remove the bag
before driving to your next pool. Transporting the Hammer-Head unit on the back of your vehicle while the debris bag is
on the vacuum head will shorten the bag's life.
The best way to clean a Hammer-Head bag is to turn it inside out. Shake the debris out of the bag and rinse with a
garden hose if necessary. Because of the fine debris it picks up, turning inside out and rinsing is the best way to clean
the HH1510 Volcano bag.
CHOOSE THE RIGHT BAG FOR THE JOB
HH1502 COARSE BAG "THE HURRICANE"
SUGGESTED USE: Heavy debris where a second cleaning is a given - Spring clean-ups and start-ups, too. Also
comes in an XL size as part number HH1502XL (46" long). True micron rating: 800
HH1506 STANDARD BAG
SUGGESTED USE: Best for larger debris and coarser sand and gravel particles. Also comes in an XL size as part
number HH1506XL (46" long). True micron rating: 200
HH1508 SUPERFINE BAG
SUGGESTED USE: Smaller and larger debris, dust and fine sand. Use this bag when the pool is mostly clean. Good
everyday bag to use once the pool is up and running normally. Also comes in an XL size as part number HH1506XL (46"
long). True micron rating: 150
HH1510 ULTRAFINE BAG "THE VOLCANO" (patented)
SUGGESTED USE: Use this bag for special cleanup and when the pool is mostly clean. Patented, no-leak design.
Tested to pick up approximately 95% of fire ash and DE powder. True micron rating: 75
MORE ABOUT DEBRIS BAGS: KNOW YOUR MICRONS
USER GUIDE 9
hammerheadvac.com/learn
V1.2 2/1/18
9
You can't see a micron with the naked eye, but filtration is measured, talked about, and bragged about in microns. So,
what is a micron? A micron is one millionth of a meter, or approximately .00003937 inches. Micron ratings are also
absolute or nominal. Absolute micron ratings mean that the filter media will filter out 90% of particles below that micron
size. Nominal micron ratings mean that the filter media will retain particles but not to any percentage greater than 50%.
To put it simply, the smaller the micron number, the finer the filtration. As debris goes, any particle below about 40
microns is smaller than the human eye can easily see.
Average diameter of a human hair: 70 microns
White blood cells: 25 microns
Talcum powder: 10 microns
Red blood cells: 8 microns
Bacteria: 2 microns
What does this mean? When a filter or bag manufacturer claims they have a 3 or 6 micron rating, you should ask
yourself: Will this really filter blood cells, or actual bacteria? We don't think so either. The truth is, there isn't much truth to
micron ratings because there is no standardized testing for these ratings. Each manufacturer can apply any rating based
on their own testing. What is really important to you, the service manager or maintenance technician, is the real-world
performance of these filter media, and of course, the Hammer-Head debris bags. Hammer-Head bags are so popular,
they are even used by owners of other vacuums. The bottom line: Don't believe every micron claim you read. With no
industry standard, the only true test is the real-world test you perform yourself.
GENERAL HAMMER-HEAD VACUUMING AND OPERATING PROCEDURE
1. Roll the cart up to the pool with the power switch towards the water.
2. Slip your pool pole onto the yoke assembly, remove the bungee cord strap, unwrap a few coils of power cord
from the cart, and set the vacuum head down on its wheels on the pool deck.
3. Attach and tighten the debris bag. (See ATTACHING THE DEBRIS BAG in this guide).
4. Lift the vacuum head unit and lower into the water.
5. Turn on the power switch and begin vacuuming. Avoid vacuuming over the debris bag. Do not let the debris bag
drag on the pool floor, as this can damage the bag and make it unusable. The vacuum head should always be
supported on the two large wheels. Vacuuming pool steps with the vacuum head hanging off the step will put
unnecessary stress on the vacuum head body and wear it out prematurely.
6. When vacuuming the pool is complete, lift the head fully out of the water upside down (wheels up, debris bag
down). Set the vacuum head down on the deck on its wheels and turn off the power switch. Avoid setting the
vacuum head down on the front decal, this will wear out the head prematurely. Avoid snagging the bag on the
pool edge, dragging it on the pool deck, or setting the vacuum on top of the bag, as this can damage the bag.
7. Remove the bag. Turn it inside out to empty it. You can also hose it off to clean it fully before the next use.
8. Remove the pool pole. Leaving the vacuum head on the deck, coil the cord back onto the cart in large loops. Do
not coil tightly. Remove any twists in the cord as you replace it on the cart.
9. Place the vacuum head back on the cart rests and secure with the safety bungee for transport. We do not
recommend transporting the unit with chemicals in the accessory tray. We do not recommend transporting the
unit with the debris bag on the vacuum head, as this can damage the bag and make it unusable.
10. We recommend using 12 volt deep-cycle marine batteries with all Hammer-Head units. Marine batteries should
be charged EVERY DAY on an automatic charger with a minimum charging rate of 6amps and a maximum of
10amps. DO NOT TRICKLE CHARGE YOUR MARINE BATTERY. Marine batteries should always remain on
an automatic charger when not in use. This will lengthen the life of the battery and ensure maximum vacuum
time per day.
UNDERSTANDING THE SMART (BLACK) SWITCH (HH1062)
USER GUIDE 10
hammerheadvac.com/learn
V1.2 2/1/18
10
The HH1062 Smart Switch was developed by Hammer-Head to add convenience, control, and protection to your
Hammer-Head Resort or Service unit. The internal circuit board monitors amperage and voltage levels to save the motor
from burnout during a jam, or while running out of the water. It has a built-in protection from reverse polarity wiring, as
well as an auto shut-off feature when out of the water. These are some of the key features and functions:
• FULL POWER MODE — press ON once — This turns on the motor with 100% power. The GREEN indicator light
around the switch will remain solid. There may be a brief delay before the motor runs, and you may see a temporary
flashing blue light and/or hear a sound before the light turns green. The blue light flash before startup is a diagnostic
light and does not indicate a problem. SOLID GREEN LIGHT = FULL POWER MODE
• LOW POWER (BATTERY SAVER) MODE — press ON, OFF, ON — This turns on the motor with 80% power. The
green indicator light will flash. In this mode the motor runs slower, conserves power, and can extend your run time
and battery life. FLASHING GREEN LIGHT = LOW POWER MODE
• AUTO REVERSE MODE — The motor can detect changes in resistance on the propeller. If the prop becomes
jammed and cannot spin, the motor will quickly reverse itself three times to clear the jam. If it cannot clear the jam
and spin freely, the switch will shut down the motor and you will see a red flashing light.
• SAFETY (SHUT DOWN) MODE — The motor has shut down because it cannot spin freely. The lights will flash
RED. Turn off the switch, pull the vacuum out of the water, and remove the obstruction. Return to vacuuming by
activating the switch in either full speed or low speed mode. FLASHING RED LIGHT = SHUT DOWN MODE
• WIRING FAULT MODE — The motor will not run and the lights will flash RED AND BLUE. This indicates that there
is a short circuit in the wiring. Inspect the wiring and battery for faulty connections. A short in the blue floating power
cord may be caused by a kink or twist. FLASHING RED AND BLUE LIGHT = WIRING FAULT MODE
The HH1062 Smart Switch can detect low
battery power levels and will not allow the
motor to run if the battery is undercharged
or has run out of power. If the motor stops
shortly after being powered up, and the
switch does not display any lights at all,
CHECK ALL WIRING CONNECTIONS
and BATTERY charge level first. Your
battery may not have enough power.
MOTOR TROUBLESHOOTING GUIDE - BASIC
USER GUIDE 11
hammerheadvac.com/learn
V1.2 2/1/18
11
PROBLEM CAUSE DO THIS
MOTOR DOES NOT RUN AT ALL BUT
BATTERY IS KNOWN TO BE GOOD, HAS
A FULL CHARGE, AND IS BEING
CHARGED DAILY AT A MINIMUM OF 6
AMPS
PROBLEM CAUSE DO THIS
VACUUM RUNS STRONG BUT BATTERY
DRAINS AFTER A FEW POOLS. THE
NEXT DAY IT DOES THE SAME THING.
POWER NOT GETTING TO MOTOR DUE
TO FAULTY SWITCH, BATTERY CONNECTIONS ARE BAD, OR THERE IS A BREAK
IN THE WIRE
BAT TERY PROBLEMS:
1. BAT TERY WATER IS LOW OR BATTERY
IS OLD
2. BAT TERY CONNECTIONS ARE WEAK
OR CORRODED
3. UNDERCHARGING - BATTERY NOT
GETTING FULL CHARGE OR IS NOT
BEING CHARGED DAILY AT A MINIMUM
6AMP OUTPUT
CHECK ALL CONNECTIONS FIRST!
CHECK TO SEE IF 30AMP FUSE HOLDER
IS PRESENT. CHECK THE FUSE.
IF ALL CONNECTIONS ARE GOOD,
THEN BY-PASS THE SWITCH AND WIRE
THE HEAD DIRECTLY TO THE BATTERY IF IT RUNS, THEN THE PROBLEM IS
WITH THE SWITCH. IF IT DOES NOT
RUN, THEN THERE IS A BREAK IN THE
WIRE OR A MOTOR SHORT
CHECK ALL CONNECTIONS FIRST!
CHARGE BATTERY AT A MINIMUM
OF 6 AMPS EVERY DAY. NO TRICKLE
CHARGING!
HAVE YOUR BATTERY CHECKED
CHECK THAT YOUR CHARGER IS
CHARGING. A FULLY CHARGED 12
VOLT BATTERY WILL TEST AT MORE
THAN 13 VOLTS.
PROBLEM CAUSE DO THIS
SLUGGISH OVERALL MOTOR PERFOMANCE
VACUUM DOES NOT RUN AS STRONG
AS WHEN IT WAS NEW
VACUUM IS GETTING SLOWER AND
WEAKER EVERY DAY
MOTOR RUNS INTERMITTENTLY
EXCESSIVE DEBRIS UNDER PROP
BAD WIRING CONNECTIONS
BATTERY PROBLEM (SEE ABOVE)
INTERNAL COMPONENTS ARE
WORN OUT
SHORT IN POWER CORD
REMOVE PROP AND CLEAN DEBRIS
OFF SHAFT
CHECK ALL ELECTRICAL CONNECTIONS FOR HEAT. IF THEY ARE HOT
WHILE THE VACUUM IS RUNNING
UNDERWATER, REPLACE OR RESET
BATTERY CONNECTIONS
LOOK FOR HEAT! HEAT INDICATES POWER LOSS,
WHICH DRAINS POWER AND SHORTENS THE LIFE OF
THE BATTERY
CONTACT HAMMERHEAD FOR
SERVICE OR REPLACE THE MOTOR/
CORD ASSEMBLY
STANDARD (RED) SWITCH WIRING (HH1061 & HH1060)
USER GUIDE 12
hammerheadvac.com/learn
V1.2 2/1/18
12
HH1061 RED ON/OFF SWITCH
(INCLUDED ONLY WITH COMPLETE UNITS)
BLUE POWER CORD
WIRE NUT WIRE NUT
NOCO GENIUS
CHARGING PORT
10 AMP AUTOMOTIVE
BLADE FUSE
HOLDER
RED
RED
WHITE
30 AMP AUTOMOTIVE BLADE FUSE
HOLDER
(MAY BE PRESENT)
BLACK WITH RED STRIPE
12 VOLT DEEP-CYCLE MARINE BATTERY
WHITE BLACK
BLACK
+
POS NEG
30 AMP AUTOMOTIVE BLADE FUSE
HOLDER
(MAY BE PRESENT)
-
POOR WIRING MAINTENANCE CAN LEAD TO SHORT CIRCUITS,
DAMAGE, OR PERSONAL INJURY FROM HEAT AND POSSIBLE FIRE!
INSPECT WIRING CONNECTIONS DAILY
SMART (BLACK) SWITCH WIRING (HH1062)
USER GUIDE 13
hammerheadvac.com/learn
V1.2 2/1/18
13
LIMITED WARRANTY
USER GUIDE 14
hammerheadvac.com/learn
V1.2 2/1/18
14
PLEASE NOTE: Warranty on all NOCO products (NOCO charging ports, battery chargers, and all associated
connections) must be submitted to NOCO directly and not to Hammer-Head Patented Performance, Inc. To find out
more about the NOCO warranty policy visit https://no.co/support/how-do-you-submit-a-warranty-claim
Hammer-Head Patented Performance, Inc. offers either a limited 6 month or 12 month warranty on select serialized
products. Your Hammer-Head serial number (where applicable) must be registered with Hammer-Head Patented
Performance, Inc. to validate any warranty claim. The serial number located on any motor/cord assembly, complete
cleaning unit, or complete vacuum head assembly is a record of the manufacturing date. If you do not register
immediately after purchase, Hammer-Head Patented Performance, Inc. will offer a limited 6-month warranty from the
date of manufacture. If you do register immediately after purchase, Hammer-Head will offer a limited 12-month warranty
from the date of your registration according to the requirements as stated on the warranty registration card. This
warranty covers manufacturing defects on complete units, motors, switches, mount assemblies, and cart frames. It does
not cover wear and tear from normal use nor does it cover wearable parts. Wearable parts include debris bags,
bearings, tires, wheels, cords, propellers, mount clamp latches, and all associated hardware. Hammer-Head units must
only be used on electric current as indicated. Damage, defects, malfunctions, or other failures of the Hammer-Head
arising from use on electrical currents other than recommended are excluded from this warranty.
Damage to Hammer-Head units or the parts thereof caused by negligent use or abuse while in the possession of the
consumer are excluded from this warranty. If the consumer or anyone other than an authorized representative does
repair or modifications to the Hammer-Head, Hammer-Head Patented Performance, Inc. can, at its discretion, void all
warranty claims based on inspection.
All warranty claims must be submitted for inspection. The decision to replace or repair any part or product is the sole
discretion of Hammer-Head Patented Performance, Inc., and cannot be made by anyone other than an official
representative of Hammer-Head. Dealers, re-sellers, and distributors may not honor, extend, or make warranty
replacements or repairs without the authorization of a Hammer-Head representative. Hammer-Head Patented
Performance, Inc. assumes no responsibility for any warranties or representations beyond the expressed terms in this
limited warranty. This limited warranty is valid and enforceable only in the United States of America on Hammer-Head
products owned and operated normally within the United States of America.
This warranty may be subject to change without notice.
Hammer-Head Patented Performance, Inc
1250 Wallace Drive Unit D
Delray Beach, FL 33444
561-278-8992
info@hammerheadvac.com
Loading...