Page 1
Keep this manual handy and in good condition for continual reference!
User Manual
Dust collector
S01
Dok.ID: 501-180-001_02 • Englisch • 2007-10-15
Page 2
2
3
Dust collector
S01
Dust collector
S01
For the safety of all personnel, it is necessary to conscientiously study this manual before assembly and
operation. This manual must be kept in good condition, as it belongs to the machine! Furthermore, keep
the manual at hand and in the vicinity of the machine so that it is accessible to personnel when they are
using, maintaining or repairing the machine.
© FELDER Maschinenbau
KR-Felder-Straße 1
A-6060 Hall in Tirol
Tel.: +43 (0) 5223 45 0 90
Fax: +43 (0) 5223 45 0 99
Email: info@felder.com
Internet: www.felder.com
18. April 2007
HAMMER
A product of the FELDER GROUP
Attention! The machine must be inspected immediately on arrival. If the machine was damaged during
transport or if any parts are missing, a written record of the problems must be submitted to the forwarding
agent and a damage report compiled. Be sure, also to notify your supplier immediately.
Page 3
3
Dust collector
S01
Table of contents
Table of Contents
1 General ...........................................................................................................................4
1.1 Legend .........................................................................................................4
1.2 Information about the manual..........................................................................4
1.3 Copyright......................................................................................................4
1.4 Liability and warranty..................................................................................... 5
1.5 Warranty notice.............................................................................................5
1.6 Spare parts ................................................................................................... 5
1.7 Disposal .......................................................................................................5
2 Safety ...........................................................................................................................7
2.1 Intended use..................................................................................................7
2.2 Manual contents ............................................................................................7
2.3 Making changes and modifications to the machine ............................................7
2.4 Responsibilities of the owner operator...............................................................8
2.5 What is required of personnel .........................................................................8
2.6 Work safety ..................................................................................................8
2.7 Personal safety...............................................................................................9
2.8 Machine hazards ........................................................................................... 9
3 Declaration of Conformity ................................................................................................10
4 Specifications................................................................................................................... 11
4.1 Dimensions and weight.................................................................................11
4.2 Operation and storage conditions..................................................................11
4.3 Noise emission............................................................................................12
5 Construction.....................................................................................................................13
5.1 Overview....................................................................................................13
6 Transport, packaging and storage.....................................................................................14
6.1 Safety instructions ........................................................................................14
6.2 Transport..................................................................................................... 14
6.3 Transport inspection......................................................................................14
6.4 Packaging...................................................................................................15
6.5 Storage.......................................................................................................15
7 Setup and installation.......................................................................................................16
7.1 Safety instructions ........................................................................................16
7.2 Installation ..................................................................................................16
7.3 Machine assembly .......................................................................................17
7.4 Electrical connection .....................................................................................19
7.5 Circuit diagram............................................................................................22
7.6 Switching on and off ....................................................................................18
8 Maintenance.................................................................................................................... 20
8.1 Safety instructions ........................................................................................19
8.2 Maintenance work .......................................................................................19
9 Spare parts...................................................................................................................... 23
10. Index .............. ............................................................................................................... 25
Page 4
4
5
Dust collector
S01
Dust collector
S01
General
Note:
This symbol marks tips and information which should be observed to ensure efficient and failure-free operation of the machine.
Attention! Risk of material damage!
This symbol marks instructions which, if not observed, may lead to material damage, functional failures
and/or machine breakdown.
Warning! Risk of injury or death!
This symbol marks instructions that must be followed in order to avoid harm to one‘s health, injuries, permanent impairment or death.
1 General
1.1 Legend
Important technical safety instructions in this manual are
marked with symbols.
These instructions for work safety must be followed. In all
these particular cases, special attention must be paid in
order to avoid accidents, injury to persons or material
damage.
Warning! Danger – electric current!
This symbol warns of potentially dangerous situations related to electric current. Not observing the safety
instructions increases the risk of serious injury or death. Required electrical repairs may only be carried out
by a trained electrical technician.
1.2 Information about the manual
This manual describes how to operate the machine
properly and safely. Be sure to follow the safety tips and
instructions stated here as well as any local accident
prevention regulations and general safety regulations.
Before beginning any work on the machine, ensure that
the manual, in particular the chapter entitled „Safety“
and the respective safety guidelines, has been read in its
entirety and fully understood. This manual is an integral
part of the machine and must therefore be kept in the
direct vicinity of the machine and be accessible at all
times. If the machine is sold, rented, lent or otherwise
transferred to another party, the manual must accompany
the machine.
1.4 Copyright
This manual should be handled confidentially. It is designated solely for those persons who work on or with the
machine. All descriptions, texts, drawings, photos and
other depictions are protected by copyright and other
commercial laws. Illegal use of the materials is punishable by law.
This manual – in its entirety or parts thereof – may not
be transferred to third parties or copied in any way or
form, and its contents may not be used or otherwise
communicated without the express written consent of the
manufacturer.
Infringement of these rights may lead to a demand for
compensation or other applicable claims. We reserve all
rights in exercising commercial protection laws.
Page 5
5
Dust collector
S01
General
1.3 Liability and warranty
The contents and instructions in this manual were compiled in consideration of current regulations and stateof-the-art technology as well as based on our know-how
and experience acquired over many years. This manual
must be read carefully before commencing any work on
or with this machine. The manufacturer shall not be liable
for damage and or faults resulting from the disregard of
instructions in the manual. The texts and images do not
necessarily represent the delivery contents.
The images and graphics are not depicted on a 1:1
scale. The actual delivery contents are dependent on
custom-build specifications, add-on options or recent
technical modifications and may therefore deviate from
the descriptions, instructions and images contained in
the manual. Should any questions arise, please contact
the manufacturer. We reserve the right to make technical
modifications to the product in order to further improve
user-friendliness and develop its functionality.
1.5 Warranty notice
The guarantee period is in accordance with national guidelines. Details may be found on our website,
www.felder-group.com
1.6 Spare parts
Use only genuine spare parts supplied by the manufacturer.
Attention! Non genuine, counterfeit or faulty spare parts may result in damage, cause malfunction or
complete breakdown of the machine.
If unauthorised spare parts are installed in the machine,
all warranty, service, compensation and liability claims
against the manufacturer and their contractors, dealers
and representatives shall be rejected.
Note: A list of authorised genuine spare parts can be found at the end of this operating manual.
1.7 Disposal
If the machine is to be disposed of, separate the components into the various materials groups in order to
allow them to be reused or selectively disposed of. The
whole structure is made of steel and can therefore be
dismantled without problem. This material is also easy
to dispose of and does not pollute the environment or
Attention! Used electrical materials, electronic components, lubricants and other auxiliary substances must
be treated as hazardous waste and may only be disposed of by specialised, licensed firms.
jeopardise public health. International environmental
regulations and local disposal laws must always be
complied with.
Page 6
6
7
Dust collector
S01
Dust collector
S01
2 Safety
At the time of its development and production, the machine was built in accordance with prevailing technological
regulations and therefore conforms to industry safety
standards.
However, hazards may arise should the machine be
operated by untrained personnel, used improperly or employed for purposes other than those it was designed for.
The chapter entitled „Safety“ offers an overview of all
the important safety considerations necessary to optimise
safety and ensure the safe and trouble-free operation of
the machine.
Additionally, in order to further minimise risks, the other
chapters of this manual contain specific safety instructions, all marked with symbols. Besides the various
instructions, there are a number of pictograms, signs and
labels affixed to the machine that must also be heeded.
These must be kept visible and legible and may not be
removed.
2.1 Intended use
The dust collector S01 is a dust and chip collecting unit
with a radial compressor and vacuums chips and dust
from wood and similar materials.
Collecting poisonous gases, vapours, fluids and foam
etc. and all other materials which form part of the MAKList is prohibited.
Attention! Any use outside the machine‘s intended purpose shall be considered improper and is therefore
not permitted. All claims regarding damage resulting from improper use that are made against the manufacturer and its authorised representatives shall be rejected. The operator shall be solely liable for any
damage that results from improper use of the machine.
The term „proper use“ also refers to correctly observing
the operating conditions as well as the specifications and
instructions in this manual.
The machine may only be operated with original manufacturer parts and accessories.
2.2 Manual contents
All those appointed to work on or with the machine must
have fully read and understood the manual before commencing any work. This requirement must be met even
if the appointed person is familiar with the operation of
such a machine or a similar one, or has been trained
by the manufacturer. Knowledge about the contents of
this manual is a prerequisite for protecting personnel
from hazards and avoiding mistakes so that the machine
may be operated in a safe and trouble-free manner. It
is recommended that the operator requests proof from
the personnel that the contents of the manual have been
read and understood.
2.3 Making changes and modifications to the machine
In order to minimise risks and to ensure optimal performance, it is strictly prohibited to alter, retrofit or modify
the machine in any way without the express consent of
the manufacturer. All the pictograms, signs and labels affixed to the machine must be kept visible, readable and
may not be removed. Pictograms, signs and labels that
have become damaged or unreadable must be replaced
promptly.
Safety
Page 7
7
Dust collector
S01
Safety
2.4 Responsibilities of the owner operator
This manual must be kept in the immediate vicinity of
the machine and be accessible at all times to all persons
working on or with the machine. The machine may only
be operated if it is in proper working order and in safe
condition. Every time before the machine is switched
on, it must be inspected for visible defects and general
condition. All instructions in this manual must be strictly
followed without reservation.
Besides the safety advice and instructions stated in this
manual, it is necessary to consider and observe local ac-
cident prevention regulations, general safety regulations
as well as current environmental stipulations that apply to
the operational range of the machine.
The operator and designated personnel are responsible
for the trouble-free operation of the machine as well as
for clearly establishing who is in charge of installing,
servicing, maintaining and cleaning the machine. Machines, tools and accessories must be kept out of the reach
of children.
2.5 What is required of personnel
Only authorized and trained personnel may work on and
with the machine. Personnel must be briefed about all
functions and potential dangers of the machine. „Specialist staff“ is a term that refers to those who – due to
their professional training, know-how, experience, and
knowledge of relevant regulations – are in a position to
assess delegated tasks and recognise potential risks. If
the personnel lack the necessary knowledge for working on or with the machine, they must first be trained.
Responsibility for working with the machine (installation,
service, maintenance, overhaul) must be clearly defined
and strictly observed. Only those persons who can be
expected to carry out their work reliably may be given
permission to work on or with the machine. Personnel
must refrain from working in ways that could harm
others, the environment or the machine itself. It is absolutely forbidden for anyone who is under the influence of
drugs, alcohol or reaction-impairing medication to work
on or with the machine. When appointing personnel to
work on the machine, it is necessary to observe all local
regulations regarding age and professional status. The
user is also responsible for ensuring that unauthorised
persons remain at a safe distance from the machine. Personnel are obliged to immediately report to the operator
any irregularities with the machine that might compromise safety.
2.6 Work safety
Following the safety advice and instructions given in this
manual can prevent bodily injury and material damage while working on and with the machine. Failure to
observe these instructions can lead to bodily injury and
damage to or destruction of the machine. Disregard of
the safety advice and instructions given in this manual as
well as the accident prevention regulations and general
safety regulations applicable to the operative range of
the machine shall release the manufacturer and their
authorised representatives from any liability and from all
compensation claims.
Page 8
8
9
Dust collector
S01
Dust collector
S01
2.7 Personal safety
When working on or with the machine, the following
must be strictly observed:
Protective gear (overalls, safety goggles, dust mask, hairnet to contain long hair, etc.)
Sturdy, tight-fitting clothing (tear-resistant, no wide sleeves).
Persons with long hair who are not wearing a hairnet are not permitted to work on or with the machine.
It is prohibited to wear gloves while working on or with the machine. All jewellery (rings, bracelets,
necklaces, etc.) must be removed before starting work on or with the machine.
When working on or with the machine, the following must always be worn by personnel:
Protective footwear
That protects the feet from heavy falling objects and prevents sliding on slippery floors.
Hearing protection
To protect against loss of hearing.
2.8 Machine hazards
The machine has undergone a hazard analysis. The
design and construction of the machine are based on the
results of this analysis and correspond to state-of-the-art
technology.
The machine is considered operationally safe when used
properly.
Nevertheless, there are some residual risks that must be
considered.
The machine runs with high electrical voltage.
Warning! Danger – electric current: electrical energy can cause serious bodily injury. Damaged insulation
materials or defective individual components can cause a life-threatening electrical shock.
• Before carrying out any maintenance, cleaning and
repair work, switch off the machine and secure it
against being accidentally switched on again.
• When carrying out any work on the electrical equip-
ment, ensure that the voltage supply is completely
isolated.
• Do not remove any safety devices or alter them to put
them out of commission.
Safety
Page 9
9
Dust collector
S01
3 Declaration of Conformity
Product designation: Dust collector
Make: HAMMER
Model designation: S01
The following EC guidelines were applied: 98/37/EG - Machine Guidelines
73/23/EWG - Low-Voltage Guidelines
93/68/EWG - Electromagnetic Tolerance
Guidelines
The following harmonised norms were applied: EN 292-1 EN 50081-2 (01.92)
EN 292-2 EN 50082-2 (03.95)
EN 60204-1
This EC Declaration of Conformity is valid only if the CE label has been affixed to the machine.
Modifying or altering the machine without the express written agreement of the manufacturer shall render the warranty null and void.
EG-Declaration of Conformity
according to Machine Guidelines 98/37/EG i.d. Fassung 98/79/EG
Manufacturer:
FELDER
KR-Felder-Straße 1
A-6060 Hall in Tirol
We hereby declare that the machine indicated below, which corresponds to the design and construction of the model
we put on the market, conforms with the safety and health requirements as stated by the EC.
Hall in Tirol, 07.08.2006
Johann Felder, Managing Director
Declaration of Conformity
Page 10
10
11
C
B
A
Dust collector
S01
Dust collector
S01
4 Specifications
4.1 Dimensions and weight
4.2 Operation and storage conditions
Operation/room temperature +10° to +40° C
Storage temperature -10° to +50° C
Basic extractor
Length A ca. 720 mm
Width B ca. 380 mm
Height C (incl Filter) ca. 1670 mm
Weight 25 kg
Motor power 0,75, 1x220 V, 50 Hz
Connection-Ø 100 mm
Chip bag contents 100 l
Volume flow max. 950 Cubic meters per hour
Fig. 1: Total size
4.4 Noise emission
The specified sound emission levels do not take into consideration a possible tolerance range for series production and are not considered appropriate to identify the
critical sound level according to the „Sound“ accident
prevention regulations. The critical sound level depends
on the running time, the use of the machine and the enviromental conditions. Therefore, the critical sound level
can only be measured in the user‘s workshop.
The specified sound pressure level was measured in a
free field at a distance of 1m from the machine and at a
height of 1,6 m.
Acoustic value
Idle 86,2 Decibel
work 99,2 Decibel
Specifications
Page 11
11
!
"
#
$
%
&
/
Dust collector
S01
Construction
5.1 Overview
5 Construction
!Base
"Collector body
#Handle bar
$Collector casters
%Filter bag Order no.: 02.1.127
&Chip bag Order no.: 02.2.013 - 10 pcs.
/Hose connection Ø 100 mm
Fig. 2: Overview
Page 12
12
13
Dust collector
S01
Dust collector
S01
6.1 Safety instructions
Warning! Risk of injury: There is a risk of injury due to falling parts while transporting, loading or unloading the machine.
Attention! Risk of material damage: The machine can be damaged or destroyed if it is subjected to improper handling during transport.
For this reason the following safety instructions must be
observed:
• Never lift loads over a person.
• Always move the machine with the utmost care and
precaution.
• Only use suitable lifting accessories and hoisting
devices that have a sufficient load-carrying capacity.
• The machine should never be lifted by its protruding
parts (e.g. working table).
• Consider the machine‘s centre of gravity when transporting it (minimise the risk of it tipping over).
• Take measures to prevent the machine from slipping
sideways.
• Ropes, belts or other hoisting devices must be equipped with safety hooks.
6.2 Transport
6 Transport, packaging and storage
• Do not use torn or worn ropes.
• Do not use knotted ropes or belts.
• Ensure that ropes and belts do not lie against sharp
edges.
• Transport the machine as carefully as possible in order to prevent damage.
• Avoid subjecting the machine to shocks.
• When transporting the machine overseas, ensure that
the packaging is airtight and that a desiccant is added to protect the metal parts against corrosion.
Attention! Transport the machine according to the enclosed transport and assembly instructions!
Never lift the machine by its planer tables. Ropes, belts and chains may only be fastened to the base.
Transport, packaging and storage
6.3 Transport inspection
Upon arrival, inspect the shipment to ensure that it is
complete and has not suffered any damage.
If any transport damage is visible, do not accept the delivery or accept it only with reservation. Record the scope
of the damage on the transport documents/delivery note.
Initiate the complaint process.
For all defects that are not discovered upon delivery, be
sure to report them as soon as they are recognised as
damage claims must be filed within a certain period, as
granted by law.
Page 13
13
Dust collector
S01
6.4 Packaging
If no agreement has been made with the supplier to
take back the packaging materials, help to protect the
environment by reusing the materials or separating them
according to type and size for recycling.
Attention! Dispose of the packaging materials in an environmentally friendly way and always in accordance with local waste disposal regulations. If applicable, contract a recycling firm to dispose of the
packaging materials.
Note: Help preserve the environment! Packaging materials are valuable raw materials and in many cases,
they can be used again or expediently reprocessed or recycled.
6.5 Storage
Keep items sealed in their packaging until they are
assembled/installed and be sure to observe the stacking
and storage symbols on the outside of the packaging.
Store packed items only under the following conditions:
• Do not store outdoors.
• Store in a dry and dust-free environment.
• Do not expose to aggressive substances.
• Protect from direct sunlight.
• Avoid subjecting the machine to shocks.
• Storage temperature: -10° to +50° C
• Maximum humidity: 60%
• Avoid extreme temperature fluctuations (condensation
build-up).
• Apply a coat of oil to all bare machine parts (corrosion protection).
• When storing for a period longer than 3 months, apply a coat of oil to all bare machine parts (corrosion
protection). Regularly check the general condition of
all parts and the packaging. If necessary, refresh or
re-apply the coat of anti-corrosive agent.
• If the machine is to be stored in a damp environment,
it must be sealed in airtight packaging and protected
against corrosion (desiccant).
Transport, packaging and storage
Page 14
14
15
Dust collector
S01
Dust collector
S01
7 Setup and installation
7.1 Safety instructions
Warning! Risk of injury: Improper assembly and installation can lead to serious physical injury or equipment damage. For this reason, this work may only be carried out by authorised, trained personnel who
are familiar with how to operate the machine and in strict observance of all safety instructions.
Warning! Danger – electric current: work on electrical fittings may only be carried out by qualified personnel and in strict observance of the safety instructions.
Before assembling and installing the machine, check to
make sure it is complete and in good condition.
Warning! Risk of injury: an incomplete, faulty or damaged machine can lead to serious physical injury or
equipment damage. Only assemble and install the machine if the machine and its parts are complete and
intact.
Attention! Risk of material damage: Only operate the machine in ambient temperatures from +10° to
+40° C. If the instructions are not followed, damage may occur during storage.
• Ensure that there is sufficient space to work around
the machine. Ensure there is ample distance between the machine and other solid constructions
such as a walls or other machines.
• Keep the work area orderly and clean. Components
and tools that are not put in their correct place or put
away may be the cause of accidents!
• Install the safety equipment according to the instructions and check that it functions properly.
Setup and installation
Characteristics of the installation site:
• Operation/room temperature: +10° to +40° C
• Ensure that the work surface is sufficiently stable and
has the proper load-bearing capacity.
• Provide sufficient light at the workstation.
• Ensure there is sufficient clearance for or from neighbouring workstations.
• Risk of injury! Keep machines, tools and accessories
etc. out of the reach of children.
• Vacuum hoses and electrical wires should be layed
in such a way as to avoid tripping over them.
7.2 Installation
Page 15
15
!
!
!
"
#
$
!
"
#
!
"
#
$
%
Dust collector
S01
7.3 Machine assembly
Setup and installation
Rolling carriage:
Turn the base plate upside-down and mount the Rollers to
the base plate using the socket head cap screws screws
(M5x8 mm) and shims as shown.
!Socket head cap screws M5x8mm
"Shims
#Nuts
$Base plate
Assembling casters to the base plate:
Screw the four long casters onto the base plate using the
supplied screw (M8x10 mm) and shims as shown.
!Collector casters - lang
"Screws M8x10 mm
#Shims
Assembling casters to the dust collector:
Screw the two short casters with the plastic brackets and
handle to the dust collector using the screws
(M8x25 mm) and shims as shown.
!Collector casters - short
"Plastic brackets
#Handle
$Screws M8x25 mm
%Shims
Fig. 3: Rolling carriage
Fig. 4: Base
Fig.. 5: Collector casters
Page 16
16
"
#
$
%
!
"
#
$
%
!
!
"
#
$
%
!
Dust collector
S01
Assembling casters to the Filter body:
Screw the two short casters with the plastic brackets to
the filter body using the screws (M8x45 mm), shims and
nuts as shown.
!Collector casters - short
"Plastic brackets
#Screws M8x45 mm
$Shims
%Nuts
Setup and installation
Connecting rolling carriage and dust collector:
1. Place the dust collector to the rolling carriage.
2. Connect rolling carriage and dust collector using the
screws (M8x16mm), shims and nuts as shown.
!Dust collector
"Rolling carriage
#Screws M6x16mm
$Shims
%Nuts
Fig. 6: Filter body casters
Fig. 8: Connecting rolling carriage and dust collector
Fig. 7: Connecting dust collector and filter body
Fig. 9: Bag rod
Connecting dust collector and filter body:
1. Apply the seal between both machine parts.
2. Connect both machine parts using shims and screws
(M6x16).
!Filter body
"Dust collector
#Seal
$Screws M6x16mm
%Shims
Assembling the filter bag support:
Insert the filter bag support into the collector holes as
shown.
!Filter bag support
Page 17
17
!
"
#
$
"
Dust collector
S01
Setup and installation
Connecting the vacuum hose:
Connect the vacuum hose with the hose clamp to the
collector body.
!Vacuum hose - Art. No. 02.0.310
"Hose clamp - Art. No. 02.0.115
Fig. 11: Vacuum hose
Assembling the filter bag:
1. Thread the ratchet strap into the filter bag.
2. Place the filter bag over the filter bag support.
The filter is tightened over the blower body using the
ratchet strap.
3. The chip bag is placed over the blower body from
be-low and is also tightened by using the ratchet
strap.
!Ratchet strap - Filter bag
"Filter bag
#Chip bag
!Ratchet strap - Chip bag
Fig. 10: Assembling the filter bag:
7.4 Electrical connection
Attach the dust collector to a separate power supply.
The electrical circuit should have a 16 A fuse.
Before connecting the dust collector to the power source,
ensure that the On/Off switch is in OFF position.
Check that the voltage requirements on the rating plate
match the power supply. Operating the machine on the
wrong voltage will damage the motor!
Attention! To protect the operator from electrical shocks, ensure that the dust collector has
been earthed.
Attention! All operations may only be executed by an authorised electrical technician!
Page 18
18
19
"
!
0,55 Kw
50 Hz
220 / 240 V
3,3 A Full load
M
OUT
IN
0
3 x 1.0 mm
L1XP
4A, gl
Fuse
L2
Limit of equipment
1
2
3
4
PE
1
Dust collector
S01
Dust collector
S01
The dust collector is equipped with an on/off switch. To
turn the dust collector on, open the switch cover first.
If the switch cover is closed, the dust collector is turned
off automatically. Upon power failure, always turn this
switch off to prevent the machine restarting automatically
once the power returns.
!On- and Off switch
"Cover
7.6 Switching on and off
Fig. 13: Switching on and off
7.5 Circuit diagram
Fig. 12: Circuit diagram
Setup and installation
Page 19
19
Dust collector
S01
Filter:
The cleanliness of the filter is an important motor power
efficiency factor. Clean the filter every time the chip bag
is changed, prior to the change, and at the very latest
once the vacuum power efficiency drops noticeably. Rap
all sides of the filter bag so the collected dust and chips
fall down into the chip bag.
To clean the dust extractor effectively, switch it off prior
to the cleaning process. Once the filter can no longer be
cleaned satisfactorily, replace it. Replace damaged filters
immediately.
Chip bag:
Empty the collection bag at the very latest when the chips
reach a level approximately 6 inches below the attachment edge. In the event of damage to the collection bag,
the bag must be replaced immediately! The dust collector
must always be switched off to change the chip bag.
Fan wheel:
Clean resin residue and chips from the impeller on a
weekly basis, at the latest when the vacuum power sinks
or the impeller becomes imbalanced.
Dust collector:
Remove chips and dust from the dust collector on a weekly basis. Remove the filter and chip bags to gain access
to the interior of the unit.
Motor and electrical equipment:
The motor and electrical equipment are maintenance
free. Ensure that the motor can always cool sufficiently
i.e., clean chips and dust from the cooling fins regularly.
Maintenance
8 Maintenance
8.1 Safety instructions
Warning! Risk of injury: improper maintenance can cause serious injury or damage. For this reason, this
work may only be carried out by authorised, trained personnel who are familiar with how to operate the
machine and in strict observance of all safety instructions.
• Before beginning any maintenance work on the machi-
ne, switch it off and secure it against accidentally being
switched on again.
• Ensure that there is sufficient space to work around the
machine.
• Keep the work area orderly and clean. Components
and tools that are not put in their correct place or put
away may be the cause of accidents!
• Following the maintenance work, re-install the guards
and check that they are functioning properly.
Warning! Danger – electric current: work on electrical fittings may only be carried out by qualified personnel and in strict observance of the safety instructions.
8.2 Maintenance work
Warning! Risk of injury!
Before you start to clean the machine, control if the machine parts have cooled down!
Switch off the device and wait for the ventilator to come to a halt.
Page 20
20
21
6
11
5 71 2
8 9 10
12 13
14
15
16
3 4
17 25 23
18
19
20
22 23
21
24 25
26
27
28
Dust collector
S01
Dust collector
S01
Spare parts
9 Spare parts
Fig. 15: Set of screws
Fig. 14: Spare parts
Item Designation Pcs.
1 Dust collector 1
2 Filter bag support 1
3 Set of screws 1
4 Ratchet strap - Filter bag 1
5 Ratchet strap - Chip bag 1
6 Base 1
7 Filter body 1
8 Chip bag 1
9 Filter bag 1
10 Seal 1
11 Steering rollers 4
12 Plastic brackets- Filter body 2
13 Plastic brackets- dust collector 2
14 Collector casters - long 4
15 Handle 1
16 Collector casters - short 1
17 Socket head cap screw M8x45mm 4
18 Socket head cap screw M8x25mm 4
19 Socket head cap screw M8x16mm 8
20 Socket head cap screw M8x16mm 6
21 Socket head cap screw M6x16mm 6
22 Shims M6 6
23 Shims M8 34
24 Socket head cap screw M5x8mm 16
25 Nuts M5 16
26 Shims M5 16
27 Allen key 5mm 1
28 Allen key 4mm 1
Page 21
21
Dust collector
S01
Index
10 Index
C
Copyright, 4
D
Dangers, 8
Declaration of Conformity, 9
Dimensions, 10
E
Electrical connection, 17
Explanations of the symbols, 4
I
Intended use, 6
Information about the manual, 4
Installation, 14
L
Liability, 5
M
Manual contents, 6
Maintenance work, 20
Motor power, 9
N
Noise emission, 10
P
Packaging, 12
Personal safety equipment, 9
R
Responsibilities of the owner operator, 7
S
Safety, 6
Safety instructions, 12,14,19
Specifications, 10
Spare parts, 5, 20
Storage, 12
T
Transport, 12
Transport inspection, 12
W
Warranty, 5
Warranty notice, 5
Work safety, 7
Page 22
Page 23
Page 24
KR-Felder-Straße 1
A-6060 Hall in Tirol
Tel.: +43 (0) 5223 / 45 0 90
Fax: +43 (0) 5223 / 45 0 99
Email: info@felder.at
Internet: www.felder.at
Loading...