Ham-Let 767LM, 767 LT Catalog Page

767 LT

REDUCER

TUBE (INCH) TO STUB (METRIC)

Ordering

Information

CONNECTORS

767LT _ 1/8 X 6 1/8 3.17 6

767LT _ 1/4 X 6 1/4 6.35 6

767LT _ 3/8 X 8 3/8 9.52 8

767LT _ 3/8 X 12 3/8 9.52 12

767 LM

REDUCING PORT
CONNECTOR

CONNECTS TWO LET-LOK® PORTS (METRIC)

767LM _ 6 X 3 6 3 2.1 22.9

767LM _ 8 X 6 8 6 4.0 24.7

767LM _ 10 X 6 10 6 4.0 25.8

767LM _ 10 X 8 10 8 5.6 26.1

767LM _ 12 X 6 12 6 4.0 29.1

767LM _ 12 X 8 12 8 5.6 29.8

767LM _ 12 X 10 12 10 7.1 30.6

767LM _ 16 X 12 16 12 8.8 37.5

767LM _ 38 X 25 *38 25 19.8 65.8

CONNECTS TWO LET-LOK® PORTS (INCH)

767LM _ 1/8 X 1/16 1/8 3.17 1/16 1.58 .03 0.75 .68 17.3

767LM _ 1/4 X 1/16 1/4 6.35 1/16 1.58 .03 0.75 .71 18.0

767LM _ 1/4 X 1/8 1/4 6.35 1/8 3.17 .08 2.03 .89 22.6

767LM _ 3/8 X 1/8 3/8 9.52 1/8 3.17 .08 2.03 .91 23.2

767LM _ 3/8 X 1/4 3/8 9.52 1/4 6.35 .17 4.20 .98 24.9

767LM _ 1/2 X 1/4 1/2 12.70 1/4 6.35 .17 4.20 1.15 29.2

767LM _ 1/2 X 3/8 1/2 12.70 3/8 9.52 .28 7.10 1.20 30.5

767LM _ 3/4 X 1/2 3/4 19.05 1/2 12.70 .39 9.90 1.49 37.9

ASSEMBLY INSTRUCTIONS

Reducer Port Connector 767 LM

(Cont’d)

Ordering

Information

Ordering

Information

A

Tube O.D.

inch mm mm inch mm inch inch mm inch mm inch mm

A1

Tube O.D.

A

Tube O.D.

mm mm mm mm

A

Tube O.D.

inch mm inch mm inch mm inch mm

Tighten the nut.

1-1/4 turns of the nut are required
for 1/4” (6 mm) and higher.
A 3/4 turn of the nut is required for 3/16”
(4 mm) and lower.

D W

.09

2.30 7/16 1.16 29.46 1.42 36.06 .50 12.7

.16

4.00 1/2 1.25 31.75 1.54 39.11 .60 15.2

.22

5.60 5/8 1.42 36.06 1.71 43.43 .66 16.8

.28

7.11 5/8 1.62 41.15 1.91 48.51 .66 16.8

A1

Tube O.D.

A1

Tube O.D.

Hex. Flat

N L I

D L

D L

* Including low friction paste, see page 91
“D” - Dimension is minimum opening.
Dimensions are for reference only,
and are subject to change without notice.

34

1/4 TURN

COMPRESSION TUBE FITTINGS