Good clear picture quality
Exquisite design
Easy to use
Thank you for choosing Buhl Screens. Please read through these instructions before use.
Easy Fold Portable Screen
Need help? Support is available at www.hamiltonbuhl.com
User Manual
r
p
Thank you for choosing our screen .Please read through th e user manual before
using the screen.Correct usage and m aintenance could insure a l onger life fo r the
roduct.
User instructions
When setting up the projection screen, care must be taken to distinguish between the front
and back of the screen fabric. Front or rear projection screen could be identified by the
card which hangs on the corner of the fabric screen or in the screen fabric bag.
Dust dirt and scratches on the projection area will affect the picture quality, take note of
the points below to prevent this.
1. Do not touch the projection area with hands.
2. Do not write or draw on the projection area.
3. Do not use fingers or sharp objects to point on the projection area, this will damage the screen
fabric.
4. Use a soft damp cloth or soft brus h to cl ean the projection area.
5. Do not use chemical cleaning agent s or al cohol t o cle an the proje ctio n area. U se cle an water only.
After using the screen, disassemble the sc r een and store it in the aluminum storage box provided.
The screen should only be operated by adults to avoid accidental damage and injury.
Product Description
Design:
The aluminum frame is designed to be light weight and easily operated.
This makes it easy to carry. assemble and disassemble.
Screen fabric:
The screen fabric is attached to the rectangular frame and held in place by several snap buttons
Which ensure an evenly stretched and perfectly flat surface.
The front projection fabric has a viewing angle of 55ºand a gain of 1.0,The rear projection fabric has
a viewing angle of 40º and a gain of 1.6.
Both types of fabric are durable and can be folded many times without any damage and the
distortion rate of frame is less than 1%.
Assembly:
The screen can be assembled in few minutes de pends on the size and without the use of tools.
The screen should be stored in an impact resistant aluminum storage box when it is not in use.
Ideal for:
Business meetings, churches, schools,
Family centers and industrial training rooms.
Correct use of the projection screen will ensure better results.
For front projection assemble and view the screen as indicated in fig.1
For rear projection assemble and view the screen as indicated in fig.2
Content and accessories list: W hen unpacking the screen, check that all the parts from the appropriate
list are there.
Use the parts as instructed by the user manual.
Parts List – 150”, 180”, 200” Sizes
Specified screen size(inches) 150、180、200
Note: The part lists abo ve ar e subject to change without prior notice .
Part Part numbe
Folding frame 1 1 Pcs
Screen fabric 2 1 Pcs
Folding legs 3 2 Pcs
Screen fabric bag 4 1 Pcs
Hand screws M8X50 5 8/10 Pcs
User manual 6 1 Pcs
QC Pass 7 1 Pcs
Fabric bag carton box 8 1 Pcs
Aluminum storage box 9 1 Pcs
Quantity
Parts diagram
1.Folding frame
4.Screen fabric bag
2.Front/rear projection
Screen fabric
5.Hand screw M8X80
M8x50
3. left and right folding legs
6.User manual
7.QC PASS 8.Fabric bag carton box 9. Aluminum storage box
10. Folding frame 11. Connecting pole 12.Hand screw M8X16
Note: the part diagrams above are subjec t to change without prior notice.
Assembly instructions
1.Take the frame out of the box and
place it on a flat surface. Unfold the
longer sections first.(Fig.3+4)
2.Unfold the frame until the latch on
the hinge ”clicks” into place. Repeat the
procedure for the shorter sections .
(Fig.5+6)
Assembly instructions
3.Make sure all 4 corners of the frame
are at 90º and the hinged support bar
is straight and not bent.(Fig.7-9)
pp
Assembly instructions
4.Take the screen fabric out of th e
screen fabric bag and put it inside the
frame next to the corner.
Unfold as shown in the diagram.
(Fig.10+11)
5. Secure the screen fabric to the frame by
snapping the buttons start from the corner
①, ② then ③, ④
(Shown in Fig.12-15)
Make sure all the buttons must be sna
ed.
Assembly instructions
6. Take the folding legs out of the box and
Unfold as shown in (Fig.16), and make sure
the hinges click into place.
7. Once the legs are locked in place,
Lay the frame on the floor and position
the legs over both sides of the frame.
Use the hand screws to attach the frame
to the legs just little before tighten two
sides of them firmly. (Fig.17+18)
Assembly instructions
8. When the frame is in the vertical
position, fold the front facing feet of the
legs out. (Fig19+20)
Assembly is now completed and the
projection screen will be stable on a f lat
surface.
Additional information for screen
size over 150”
Use the hand screws to secure the
support leg to the frame in an
appropriate position. The support leg
can be adjusted to an appropriate
length. (Fig.21-23)
The proje c tion screen parts and specific a tions are subject to change without prior
Assembly instructions
9. After using the screen, disassemble
and store it in the aluminum storage box
provided. To disassemble the screen,
implement the assemble procedure in
reverse order.
Safety Notice
Misuse of the screen may cause
damage to the screen, or injury
Warnin
Do not climb
on the screen
Note: If the screen is faulty or is damaged in any way. Do not try to repair the projection
screen yourself. Contact customer service to arrange it to be repaired.
notice.
to persons.
Do not hang things from the
screen or climb on it. Doing so
may cause the screen to fall off
and damage the screen and
cause injury .
The projection screen must be set up on a
stable surface w here there is suffici ent
space. Failure to do so may cause the
screen to fall over causing damage to the
Notice
screen and injury to persons.
After using the pr ojection scr een
Disassemble the screen and store it in
the aluminum storage box provided.
This will protect it from dust, dirt and
Warnin
accidental damange.
2.Unfold the
frame until the
latch on
the hinge ”clicks”
Notice
Do Not
Do not touch the projection
area with hands
Do not write or draw on
the projection area.
Correct
Use a soft damp cloth or soft brush
to clean the projection area.
After using the screen, disassemble
the screen and store it in the aluminum
storage box provided.
Do not use chemical cleaning
agents or alcohol to clean the
projection area
Do not disassemble
the screen when it is in use.
Use clean water and a soft damp
cloth to clean the screen.
Loading...