Hamilton Beach HBH650 User Manual

www.commercial.hamiltonbeach.com

840160300

3/07

www.commercial.hamiltonbeach.com

Modèle HBH650

Mélangeur de bar

Manuel d’utilisation

Page 14

Model HBH650

Bar blender

Operation Manual

Page 2

Modelo HBH650

Licuadora para bar

Manual de uso

Página 26

READ BEFORE USE. LIRE AVANT D’UTILISER. LEA ANTES DE USAR.

STO

LSE

Blender Safety

IMPORTANT: This operation manual should be reviewed with all equipment operators as part of your operator training program.

1. Read the Operation Manual before using blender. Keep Operation Manual handy.

2. Plug into a grounded 3-prong outlet.

3. Do not remove ground prong.

4. Do not use an adapter.

5. Do not use an extension cord.

6. Disconnect power before cleaning or servicing.

7. To reduce risk of personal injury, unplug cord from

outlet when not in use, and before putting on or taking off parts.

8. To protect against electrical shock, do not immerse cord, plug, or blender base in water or any other liquid.

9. Do not spray the base with a high-pressure spray gun.

10. Extreme caution must be used when moving an

appliance containing hot oil or other hot liquids.

11. Do not use appliance for other than intended use.

12. Not intended for use by or near children.

13. The use of accessory attachments not recommended

by Hamilton Beach may cause injuries.

14. To reduce risk of personal injury and to prevent damage to blender or container and cutter assembly, DO NOT insert utensils into blender container while operating blender.

15. Do not store any kitchen utensils in the container because the blender would be damaged if inadvertently turned on.

16. To prevent possibility of serious personal injury, keep hands out of blender container while operating blender. Always operate blender with container lid in place.

17. Avoid contacting moving parts.

18. Blades are sharp. Handle carefully.

19. If cutter assembly blades are loose, discontinue use

immediately and replace cutter assembly. Do not attempt to repair or tighten cutter assembly.

– SAVE THESE INSTRUCTIONS –

20. Inspect container and cutter assembly daily. Do not use broken, chipped or cracked container. Check cutter for wear, nicks, or broken blades. Do not use broken or cracked cutting blades.

21. Do not use outdoors.

22. This appliance is intended for short periods of

operation, with a rated operating time of 3 minutes.

23. Do not leave blender unattended while it is operating.

24. To prevent damage to blender, container, or cutter

assembly, DO NOT move or shake blender while in operation.

25. When blending hot liquids, remove center-piece of two-piece lid. Hot liquids may push lid off jar during blending. To prevent possible burns: Do not fill blender jar beyond the 1 quart (1 liter) level. With the protection of an oven mitt or thick towel, place one hand on top of lid. Keep exposed skin away from lid. Start blending at lowest speed.

26. Always operate blender with container lid in place.

27. Do not operate any appliance with a damaged cord or

plug or after the appliance malfunctions, or is dropped or damaged in any manner. Call the Technical Service number, 866-285-1087 or 910-693-4277, for instructions on examination, repair, or electrical or mechanical adjustment.

IMPORTANT SAFETY INSTRUCTIONS

WARNING – When using electrical appliances, basic safety precautions should be followed, including

the following:

For assistance or replacement parts, call our Technical Service number:

866-285-1087 or 910-693-4277

8 a.m. – 5:00 p.m. EST Monday – Friday

www.commercial.hamiltonbeach.com

Technical Service

Cut Hazard

Always place lid on container when blending.

Do not put hands, spoons, or other utensils in container when blending.

Failure to follow these instructions can result in broken bones, cuts, or other injuries.

Burn Hazard

Always use caution when blending hot contents.

Failure to follow these instructions can result in burns.

Sanitize using 1 tablespoon (15 ml) of household bleach per 1 gallon (3.8 liter) of clean, cool water (60°F/16°C), mixed according to the instructions on the bleach.

1. Fill container with sanitizing solution, replace lid and filler cap and run on LOW speed for 2 minutes. Empty container.

2. Wipe exterior with soft cloth dampened with sanitizing solution.

3. Immerse lid and filler cap in sanitizing solution for 2 minutes.

4. Place empty container on base and run on HIGH speed for 2 seconds to remove any moisture from the cutter assembly.

5. When ready to use, rinse with clean water.

Sanitizing

Electrical Shock Hazard

Disconnect power before cleaning blender base.

Failure to follow these instructions can result in death or electrical shock.

Electrical Shock Hazard

Plug into a grounded outlet. Do not remove ground. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can

result in death, fire, or electrical shock.

Replacement Parts

64 oz. polycarbonate container 6126-650 Cutter assembly 98650

Part Description

Part Number

The following components are subject to wear and should be replaced at least yearly. We recommend keeping a replacement container and cutter on hand.

The parts and features for the Tempest blender are shown on this page. Become familiar with all parts and features before using your blender.

Your Tempest blender is designed for blending and mixing beverages.

Lid

64 oz. Polycarbonate Container

Removable Filler Cap

Control Panel

Blender Base

Cutter Assembly

Jar Pad

Reset Switch/ Circuit Breaker

Control Panel

Stop

High Speed

Low Speed

Jump Cycle

Pulse

Power ON (I)/OFF (O)

Timer Knob*

Motor Temperature

Jar Pad

Indicator

Parts and Features

* = 3 Min. Max

POW

IGH

PUL

120 VAC, 60Hz

Power Requirements

Use a fused electric outlet for the blender. Depending on the model of your blender, the plug will look like the following to meet power requirements:

Blender Operation – Quick Start Guide

1. Read Important Safety Instructions and Warnings before use.

2. Place the blender on a dry, level surface.

3. Make sure the power switch is OFF (O). Plug the

blender into a grounded 3-prong electrical outlet.

4. Place the container on the base with ingredients and container lid in place.

5. Press the Power ON (I)/OFF (O) button to turn the blender ON (I). The red LED lamp indicates that power is ON (I).

6. Adjust the timer knob to desired run time.

7. Select the desired function (HIGH, LOW or JUMP). NOTE: Use the Jump Cycle for automatic speed

adjustment from LOW to HIGH during the blending cycle.

Ground

prong

230 VAC, 50Hz

1 2 3

Press Power ON (I).

Set operating time.

Select speed.

= 3 Min. Max

1 2 3

00:02

:00

00:00

:03

Remove jar within

Blender will automatically turn off after 2 minutes of low-speed “cool down cycle”.

Thermal Overload Protection

1 2 3

Replacing the Cutter Assembly

Problem . . . Solution . . .

Blender fails to start or stops while it is running and the red temperature light is on.

• Thermal overload protection has been tripped. Attempt to run “cool down cycle” or allow unit to cool until temperature light is green. See “Thermal Overload Protection” for additional details.

Ingredients will not mix properly

• Check to see if enough liquid has been added to the ingredients. Mixture should be fluid and free-running at all times.

• Solid pieces are too large.

• Container is too full. Do not fill past highest graduation marking.

• Cutter assembly blades are not sharp or are damaged. Inspect container and cutter assembly daily. Replace cutter assembly at least yearly or sooner if cutter assembly appears worn or damaged.

• Check to see if cutter assembly is installed properly.

• Select speed to create a fluid blend.

Blender fails to start or stops while it is running and jar pad light is blinking.

• Make sure that the jar is seated properly on the blender base. When the jar is properly positioned, the light will go off.

• Blender will not operate unless jar is properly seated.

Motor temperature light is yellow or red.

• The motor is overheating. Try mixing smaller batches or running for shorter cycle times. Allow motor to cool between batches. See “Thermal Overload Protection” for additional details.

Troubleshooting Guide

Blender fails to start or stops while it is running and no lights show on the control panel.

• Make sure that the main power ON (I)/OFF (O) button is ON (I).

• Check to see if unit is securely plugged into an electric outlet of the proper voltage and frequency.

• Check to see if the fuse for the electric outlet has blown or if a circuit breaker has tripped.

• Check the integrated circuit breaker on the bottom of the blender base. If it trips again immediately or frequently, contact Customer Service.

Unplug the blender and remove the container from the base, and then inspect the container and cutter assembly for wear, nicks, and broken or loose blades. Replace if necessary. If the blades are loose, discontinue use immediately and replace the blades. Do not attempt to repair or tighten the cutter assembly. See “Replacement Parts”.

Unplug the blender, and then inspect the power cord insulation and power plug for cracks. Refer to “Technical Service” for repair or replacement. Remove jar from blender base. Inspect the cutter by rotating the drive end of the cutter by hand. It should turn smoothly. If it does not, replace the cutter assembly. See “Replacing the Cutter Assembly” for details.

Inspect the blender and its various parts and replace as follows:

Daily

Weekly

Maintenance

+ 28 hidden pages