Hamilton Beach HBH550 Installation Manual

Model HBH550

Bar Blender

Operation Manual

Page 2

Modèle HBH550

Mélangeur de bar

Manuel d’utilisation

Page 7

Modelo HBH550

Licuadora para Bar

Manual de Uso

Página 12

READ BEFORE USE. LIRE AVANT D’UTILISER. LEA ANTES DE USAR.

840220901

11/12

Find Recipes and Demo Videos at

www.commercial.hamiltonbeach.com

Blender Safety

IMPORTANT: This operation manual should be reviewed with all equipment operators as part of your operator training program.

IMPORTANT SAFETY INSTRUCTIONS

WARNING – When using electrical appliances, basic safety precautions should be followed,

including the following:

1. Read the Operation Manual before using blender. Keep Operation Manual handy.

2. Plug into a grounded 3-prong outlet.

3. Do not remove ground prong.

4. Do not use an adapter.

5. Do not use an extension cord.

6. Disconnect power before cleaning or servicing.

7. To reduce risk of personal injury, unplug cord from

outlet when not in use, and before putting on or taking off parts.

8. To protect against electrical shock, do not immerse cord, plug, or blender base in water or any other liquid.

9. Do not spray the base with a high-pressure spray gun.

10. Extreme caution must be used when moving an

appliance containing hot oil or other hot liquids.

11. Do not use appliance for other than intended use.

12. Not intended for use by or near children.

13. Children should be supervised to ensure that they

do not play with the appliance.

14. The appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

15.

The use of accessory attachments not recommended

by the appliance manufacturer may cause injuries.

16. To reduce risk of personal injury and to prevent damage to blender or container and cutter assembly, DO NOT insert utensils into blender container while operating blender.

17. Do not store any kitchen utensils in the container because the blender would be damaged if inadvertently turned on.

18. To prevent possibility of serious personal injury, keep hands out of blender container while operating blender. Always operate blender with container lid in place.

19. Avoid contacting moving parts.

20. Blades are sharp. Handle carefully.

21. If cutter assembly blades are loose, discontinue use

immediately and replace container. Do not attempt to repair or tighten cutter assembly.

22. Inspect container and cutter assembly daily. Do not use broken, chipped or cracked container. Check cutter for wear, nicks, or broken blades. Do not use broken or cracked cutting blades.

23. Do not use outdoors.

24. This appliance is intended for short periods of

operation, with a rated operating time of 3 minutes.

25. Do not leave blender unattended while it is operating.

26. To prevent damage to blender, container, or cutter

assembly, DO NOT move or shake blender while in operation.

27. When blending hot liquids, remove center-piece of two-piece lid. Hot liquids may push lid off jar during blending. To prevent possible burns: Do not fill blender jar beyond the 1 quart (1 liter) level. With the protection of an oven mitt or thick towel, place one hand on top of lid. Keep exposed skin away from lid. Start blending at lowest speed.

28. Always operate blender with container lid in place.

29. Do not operate any appliance with a damaged cord

or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Call the Technical Service number, 866-285-1087 or 910-693-4277, for instructions on examination, repair, or electrical or mechanical adjustment.

– SAVE THESE IN STRUC TIONS –

Electrical Shock Hazard

Disconnect power before cleaning blender base.

Failure to follow these instructions can result in death or electrical shock.

Electrical Shock Hazard

Plug into a grounded outlet. Do not remove ground. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can

result in death, fire, or electrical shock.

Cut Hazard

Always place lid on container when blending.

Do not put hands, spoons, or other utensils in container when blending.

Failure to follow these instructions can result in broken bones, cuts, or other injuries.

Burn Hazard

Always use caution when blending hot contents.

Failure to follow these instructions can result in burns.

Sanitizing

Sanitize using 1 tablespoon (15 ml) of household bleach per 1 gallon (3.8 liter) of clean, cool water (60°F/16°C), mixed according to the instructions on the bleach.

1. Fill container with sanitizing solution, replace

lid and filler cap and run on LOW speed for 2 minutes. Empty container.

2. Wipe exterior with soft cloth dampened with

sanitizing solution.

3. Immerse lid and filler cap in sanitizing solution

for 2 minutes.

4. Place empty container on base and run on HIGH

speed for 2 seconds to remove any moisture from the cutter assembly.

5. When ready to use, rinse with clean water.

Technical Service

For assistance or replacement parts, call our Technical Service number:

Replacement Parts

The following component is subject to wear and should be replaced at least yearly. We recommend keeping a replacement container on hand.

Part Description

64 oz. polycarbonate container

1817

866-285-1087 or 910-693-4277

8 a.m. – 5:00 p.m. EST Monday – Friday

www.commercial.hamiltonbeach.com

Part Number

6126-650-OP

Parts and Features

The parts and features for the blender are shown on this page. Become familiar with all parts and features before using your blender.

Your blender is designed for blending and mixing beverages.

Removable Filler Cap

Lid

64-oz. Polycarbonate Container

ON/OFF/Circuit Breaker

Control Panel

Timer Knob*

* = 3 Min. Max

Cutter Assembly

Jar Pad

Blender Base

Control Panel

High Speed Start

Low Speed

(Pulse runs at

high speed)

ON (I)

STOPPulse

Light indicates ready to operate

Troubleshooting Guide

Problem . . . Solution . . .

Blender fails to start or stops while it is running.

Ingredients will not mix properly

• Make sure the power switch on bottom of unit is set to RESET (ON/I) and the control panel switch is in the ON (I) position.

• Check to see if unit is securely plugged into an electric outlet of the proper voltage and frequency.

• Check to see if the fuse for the electric outlet has blown or if a circuit breaker has tripped.

• If the motor stops during operation due to overheating, unplug and allow the unit to cool down for 15 minutes. Plug unit into electric outlet to resume normal operation.

• Check the ON/OFF/Circuit Breaker on the bottom of the blender base. If it trips again immediately or frequently, contact Technical Service.

• Check container to make sure cutter assembly spins freely. If cutter cannot be turned, the container needs to be replaced.

• Check to see if enough liquid has been added to the ingredients. Mixture should be fluid and free-running at all times.

• Solid pieces are too large.

• Container is too full. Do not fill past highest graduation marking.

• Cutter assembly blades are not sharp or are damaged. Inspect container and cutter assembly daily. Replace container at least yearly or sooner if cutter assembly appears worn or damaged.

• Select speed to create a fluid blend.

Maintenance

Inspect the blender and its various parts and replace as follows:

Daily

Weekly

Unplug the blender and remove the container from the base, and then inspect the container and cutter assembly for wear, nicks, and broken or loose blades. If the blades are loose, discontinue use immediately and replace the container. See “Replacement Parts”.

Unplug the blender, and then inspect the power cord insulation and power plug for cracks. Refer to “Technical Service” for repair or replacement. Remove jar from blender base. Inspect the cutter by rotating the drive end of the cutter by hand. It should turn smoothly. If it does not, replace the container.

Notes

+ 14 hidden pages