Hamilton Beach 840125800 User Manual
840125800
Stand Mixer
English ................................................ 2
USA: 1-800-851-8900
Canada : 1-800-267-2826
México: 01 800 71 16 100
2
Consumer Safety Information
IMPORTANT SAFEGUARDS
1. Read all instructions.
2. To protect against risk of electrical
shock, do not put the cord, plug, or
Mixer body in water or other liquid.
3. Close supervision is necessary when
any appliance is used by or near children.
4. Unplug from outlet when not in use,
before putting on or taking off parts,
and before cleaning.
5. Remove beaters and other attachments
from the Mixer before washing.
6. Do not operate any appliance with
a damaged cord or plug or after the
appliance malfunctions or is dropped
or damaged in any manner. Call our
toll-free customer service number for
information on examination, repair, or
electrical or mechanical adjustment.
7. The use of attachments not recommended or sold by the appliance manufacturer
for use with this model may cause fire,
electric shock or injury.
8. Avoid contacting moving parts. Keep
hands, hair, and clothing, as well as
spatulas and other utensils, away from
beaters during operation to reduce risk
of injury to persons, and/or damage to
the Mixer.
9. Do not use outdoors.
10. Do not let cord hang over edge of table
or counter. Do not let cord contact hot
surfaces, including stove.
11. Do not place on or near a hot gas or
electric burner, or in a heated oven.
12. Check that control is off before plugging
cord into wall outlet. To disconnect, turn
control to O/OFF, then remove plug
from wall outlet.
13. Do not use appliance for other than
intended purpose.
SAVE THESE INSTRUCTIONS
This appliance is intended for household
use only.
This appliance is equipped with a groundedtype 3-wire cord (3-prong plug). This type of
plug will only fit into an electrical outlet
made for a 3-prong plug. This is a safety
feature intended to help reduce the risk of
electrical shock. If the plug should fail to fit
contact a qualified electrician to replace the
obsolete outlet. Do not attempt to defeat
the safety purpose of the grounding pin by
modifying the plug in any way.
To avoid an electrical circuit overload do not
use another high wattage appliance on the
same circuit with the mixer.
The length of the cord used on this appliance was selected to reduce the hazards
of becoming tangled in, or tripping over a
longer cord. If a longer cord is necessary an
approved extension cord may be used.
The electrical rating of the extension cord
must be equal to or greater than the rating
of the mixer. Care must be taken to arrange
the extension cord so that it will not drape
over the countertop or tabletop where it can
be pulled on by children or accidentally
tripped over.
An extension cord should be connected to
the appliance first, before it is plugged into
the outlet.
When using electrical appliances, basic safety precautions should always be observed,
including the following:
3
Parts and Features
1. Mixer Head
2. Setting Control
Select a setting from 2 to 12.
A higher setting
generates in a
faster speed.
3. Mixer Release Button
This button unlocks the Mixer Head
to raise or lower it.
Press up on the
button to release
the Mixer Head.
The Mixer Head
should be locked
down when mixing.
The Mixer Head should be locked
in the upright position when adding/
removing mixer attachments and
bowl.
4. Logo Plate
5. Attachment Shaft
6. Attachments
Mixer attachments include a flat
beater, a wire whisk, and a dough
hook.
7. 41⁄
2 Quart Mixing Bowl
8. Bowl Lock
4
How to Assemble the Mixer
IMPORTANT: To remove or insert the Bowl or Attachments, the Mixer Head must
be raised and locked in the UP position.
1. Make sure that Setting Control is set
to OFF and the Mixer is unplugged.
2. Press the Mixer Release Button and
tilt the Mixer Head up.
3. Place Bowl on bowl lock and turn
clockwise until Bowl is locked.
4. Plug Mixer into electrical outlet.
To Remove:
1. Make sure that Setting Control is set
to OFF and the Mixer is unplugged.
2. Press the Mixer Release Button and
tilt the Mixer Head up.
3. Turn Bowl counterclockwise to
unlock.
To Attach the Bowl
wWARNING
Injury Hazard
Unplug mixer before inserting or removing beaters.
Unplug mixer before cleaning. Failure to do so can result in broken
bones or cuts.
1. Make sure that the Setting Control
is set to OFF and the Mixer is
unplugged.
2. Press the Mixer Release Button and
tilt the Mixer Head up.
3. Insert Attachment onto Beater Shaft
and press upward as far as possible.
4. Turn the Attachment to the right,
hooking beater over pin on shaft.
5. Plug Mixer into electrical outlet.
To Attach the Beater, Wire Whisk, or Dough Hook
Loading...