Hamilton Beach 840074800 User Manual

Humidifier

840074800

Humidifier Safety............................ 2

Know Your Humidifier.................... 4

How to Assemble and Use............ 5

How to Clean................................ 11

Troubleshooting Guide ................ 14

Customer Service.......................... 16

In USA: 1-800-851-8900

In Canada: 1-800-267-2826

2

IMPORTANT SAFEGUARDS

SAVE THESE INSTRUCTIONS!

Humidifier Safety

1. Read all instructions before using this
humidifier. Save these instructions
for reference.

2. Always place the humidifier on a firm,
flat, level, water-resistant surface.

3. To reduce the risk of electrical shock,
never plug humidifier into an outlet
while your hands are wet.

4. Never drop or insert any objects into
any openings.

5. Never place the humidifier in a location
where it is accessible to children.

6. Do not place the humidifier on or
near heat sources such as stoves,
radiators, heaters, or in direct sunlight.

7. Never connect the humidifier to any
power source other than 120 V AC.

8. Always unplug the humidifier before
refilling, cleaning, servicing, or moving.

9. Before each use, check the cord and
plug for damage. Do not operate any
appliance with a damaged cord or plug,
or after the appliance malfunctions or
is dropped or damaged in any manner.
Call our toll-free customer service number
for information on examination, repair or
electrical or mechanical adjustment.

10. Always unplug and empty humidifier
and tank when it is not in use.

11. Never tilt or attempt to move the
humidifier or supporting surface while
it is operating or full of water. Turn off
and unplug the humidifier before
removing the water tank and moving
the unit.

12. This humidifier requires regular
cleaning and maintenance. Refer
to the instructions in the “How to
Clean” section. Never clean the
humidifier in a manner other than
described in this manual.

13. Do not immerse fan enclosure in
water or other liquids, or allow it
to get wet.

14. Never use detergents, household
cleaners, or other solvents to clean the
humidifier, other than those specified
in the Cleaning Instructions provided
in this manual.

15. Do not direct output from unit at walls,
furniture, or the like.

16. Do not use filters or other replacement
parts not recommended or sold by
Hamilton Beach/Proctor-Silex, Inc.

17. To disconnect cord, turn the control
to OFF, then remove plug from
wall outlet.

18. Do not use appliance for other than
its intended purpose.

19. Never stand or sit on any part of the
humidifier, and never place objects
on the humidifier.

READ AND SAVE THESE INSTRUCTIONS.

When using electric appliances, basic safety precautions should always be followed,
including the following:

3

Consumer Safety Information

This appliance is intended for
household use only.

This appliance is equipped with a
polarized plug. This type of plug has
one blade wider than the other. The
plug will fit into an electrical outlet
only one way. This is a safety feature
intended to help reduce the risk of
electrical shock.

If you are unable to insert the plug into
the outlet, try reversing the plug. If the
plug should still fail to fit, contact a
qualified electrician to replace the
obsolete outlet. Do not attempt to
defeat the safety purpose of the
polarized plug by modifying the plug
in any way.

If a longer cord is necessary an
approved extension cord may be used.
The electrical rating of the extension
cord must be equal to or greater than
the rating of the humidifier. Care must
be taken to arrange the extension cord
so that it will not drape over the coun­tertop or tabletop where it can be
pulled on by children or accidentally
tripped over.

Do Not Over-humidify

Do not over-humidify. The suggested
level for the best health benefit is 50%.
Some units can be set for desired
humidity ranges from 20 to 90%, but
care should be taken not to over­humidify, which will be dependent on
both the construction of your home
and the outside weather conditions.

Do not allow water to condense on
walls, floors, or windows as water
damage could result. If you see these
conditions occur, lower the desired
humidity level on the humidifier or turn
the unit off. Hamilton Beach/Proctor­Silex, Inc. will not be responsible for
damage caused by water.

Before First Use

Be sure to remove all packing materials.
Choose a flat, level, water-resistant
location for the humidifier that will allow
for good air circulation and that is not
accessible to children.

Do not place the humidifier where it
or its cord presents a tripping or
stumbling hazard, or where the air
vents are blocked.

4

Know Your Humidifier

Parts and Features

Fan Enclosure

1. Control Panel

2. Exhaust Grille

3. Cord Wrap (see page 6)

4. Air Intake Grilles

Water Tank Assembly

5. Carrying Handle

6. Water Tank

7. Gasket

8. Filler Cap

Base Assembly

9. Filter

10. Water Tray

11. Humidifier Base

DO NOT:

• Do not stand, sit, or place any
objects on
the humidifier.
It is not
designed
to support
additional
weight.

• Do not block the air intake and

exhaust grilles. This will cause poor
performance and may cause moisture
damage and mildew build-up.

• Do not use in a small, enclosed

space or in an area with a humidity
level above 50%. Excessive humidity
could result.

• Do not place on or near heat sources

such as stoves, radiators, or heaters,
or in direct sunlight.

• Never place the humidifier in a

closed room. A closed room may
result in excessive humidity.

• To reduce electrical noise and

interference, do not place on or near,
or plug into the same outlet as, TVs,
baby monitors, or cordless phones.

5

How to Assemble and Use

IMPORTANT: Your Hamilton Beach humidifier is designed for easy use and
maintenance. Make sure that the water tray and filter are properly installed before
filling the tank and operating the humidifier.

DO NOT USE THE HUMIDIFIER WITHOUT THE FILTER IN PLACE!

Selecting the Proper Location

To prevent the risk of injury or damage to the humidifier and furnishings and
provide the best possible performance of your humidifier, follow the placement
guidelines below:

DO:

• Place the humidifier on a flat, stable,
waterproof
surface.

• Place the humidifier along an inside

wall near an electrical outlet where
it is out of the way and it and its cord
do not present

a tripping hazard.

• Select a location with adequate

air circulation.

• Leave at least six inches (15 cm)

between the humidifier and any walls
or furnishings. Failure to do so could
cause poor air circulation and
mildew or moisture damage to walls
or furniture.

• Unplug the humidifier and empty the

water tank and tray if the humidifier is
to be moved, or will not be used
for several days.

6

1. Insert the water tray into the humidifier

base. Be
sure that it
is securely
seated in
the indent
in the base.

4. Set the fan enclosure onto the
humidifier
base. Make
sure that
the filter
lines up
with the
fan cover.

2. Place the filter on the water tray
as shown.

3. Slide the cord through the notch at
the bottom
of the cord
wrap com­partment.
Excess cord
can be
stored in
the cord wrap
compartment.

Humidifier Assembly

1. Remove the filler cap on the bottom

of the tank
by turning it
counter­clockwise
until the
UNLOCK
arrows line
up with the
ridges on
the tank.

2. Fill the tank with COOL tap water.
DO NOT
USE HOT
WATER.
Be sure to
keep the
tank free of
debris.

NOTE: Using distilled or deionized
water will prolong the life of the filter.

3. Replace the filler cap and turn
clockwise
until the
LOCK
arrows line
up with the
ridges on
the tank
opening.
Return the
tank to
an upright

position. When carrying the tank, use
the carry handle and support the
tank from the other side.

NOTE: Always make sure the filler
cap is locked and the gasket is in
place before inverting water tank.

7

Filling the Water Tank

Unlocked
Position

Locked
Position

Filter Tip!

To prolong the life of the filter, it is
recommended that you turn over the
filter each time you fill the water tank.

8

Placing the Water Tank on the Base

Lower the tank into place until it is

properly seated,
using the fan
enclosure and
the base to align
the tank.

IMPORTANT! Never pour water into
or allow water to splash into air intake
or exhaust grilles.

NOTE: Some water will flow out of
the tank and into the water tray when
the tank is in position.

CAUTION: Once the humidifier has
been filled, do not attempt to tilt or
move it. If it is necessary to move
the humidifier, make sure it is
unplugged and remove the water
tank first.

Plugging in the Humidifier

WARNING: To reduce the risk of
electrical shock, never plug in the
humidifier while your hands are wet!

Once the humidifier has been assembled
and placed in its final location, and the
tank has been filled, plug the humidifier
into a wall outlet.

NOTE: The polarized plug will only
fit in one direction—DO NOT try
to force the plug! If you are unable to
insert the plug into the outlet, try
reversing the plug. If the plug still does
not fit, contact a qualified electrician to
replace the obsolete outlet.

9

Setting the Controls –

2-Speed Humidifier

1. Fan Speed Knob

2. Power On Indicator – lights

when unit is on.

1. Fan Speed Knob

2. Power On Indicator – lights

when unit is on.

3. Desired Humidity Indicator –

lights when desired humidity is
reached.

4. Desired Humidity Setting Knob

Setting the Controls –

2-Speed Humidifier with Humidistat

Setting the fan speed

Turn the fan speed knob to the
desired setting. To increase the
humidity in a room more quickly, set
the knob to HI. For quiet, nighttime
operation or for a more gradual
increase, set the knob to Quietmist™.

Indicator lights

The power on indicator will light to
indicate that the humidifier is on.

Setting the fan speed

Turn the fan speed knob to the
desired setting. To increase the
humidity in a room more quickly, set
the knob to HI. For quiet, nighttime
operation or for a more gradual
increase, set the knob to Quietmist™.

Setting the humidistat

The desired humidity knob allows
you to set the humidifier to cycle on
and off to maintain a selected humidity
level. Turn the knob clockwise for
higher humidity, counterclockwise for
less. Once the desired humidity level is
reached, the desired humidity indicator
will light and the fan will turn off (unit
is in stand-by mode).

Indicator lights

The power on indicator will light
to indicate that the humidifier is on.

Quietmist

™

For quiet, nighttime operation or
for a more gradual increase in the
humidity level, set the knob to
Quietmist.™

10

Setting the fan speed

Turn the fan speed knob to the
desired setting. To increase the
humidity in a room more quickly, set
the knob to HI. For normal operation,
set the knob to MED. For quiet,
nighttime operation or for a more
gradual increase, set the knob to
Quietmist™.

Setting the electronic humidistat

The electronic humidistat allows you to
set the humidity within a range from
20% to 90%, in 5% increments. The
current room humidity level is displayed
in large numbers, while the desired
humidity level is displayed in smaller
numbers. If the current room humidity
level drops below 20%, the display will
show LO. If it is higher than 90%, HI

will be displayed. Press the ▲ and ▼

buttons to adjust the humidity level. The
humidifier will then turn on automatically
whenever the current room humidity
drops more than 2% below the desired
humidity. Once the desired humidity is
reached, the fan will turn off and the
unit will go into stand-by mode.

Indicator lights

The power on indicator will light to
indicate that the humidifier is on.

1. Fan Speed Knob

2. Humidity Setting Buttons (▲/▼)

3. Power On Indicator – lights when

unit is on

Digital Display

4. Current Room Humidity Percentage

5. Desired Humidity Percentage

Setting the Controls –

3-Speed Humidifier with
Electronic Humidistat

Quietmist

™

For quiet, nighttime operation or
for a more gradual increase in the
humidity level, set the knob to
Quietmist.™

11

wWARNING

To reduce risk of electric shock:

• Always unplug before cleaning.

• Do not immerse fan enclosure in water or other liquid.

Daily Maintenance:

1. Turn off the humidifier and unplug it

from electrical outlet.

2. Lift off the fan enclosure and remove
the filter.

3. Remove the water tank and tray
and carry them to the sink. Pour
any remaining water into the sink.

4. Rinse the water tray and tank
thoroughly to remove any dirt or
sediment. Wipe clean, then dry
with a clean cloth or paper towel.

5. Reinstall the water tray and filter,
replace the fan enclosure, and refill
the water tank with cool tap water
as instructed on page 7.

NOTE: To prolong the life of the filter,
it is recommended that you turn over
the filter each time you fill the water
tank.

How to Clean

The evaporative, wick-type humidifier
adds moisture to the air in the form of
water vapor, by using a fan to force air
through a moistened-filter medium.

To ensure the proper and efficient
operation of your humidifier, the
following cleaning and maintenance
procedures must be followed.

Failure to follow the recommended care
and maintenance instructions could
lead to a buildup of micro-organisms,
including algae, bacteria, and mildew,
which may lead to respiratory or other
ailments in some individuals.

Cleaning the Humidifier

Wipe the fan enclosure, control panel, and cord with a damp cloth or sponge.

Weekly Maintenance:

1. Turn off the humidifier and unplug

it from electrical outlet.

2. Lift off the fan enclosure and remove
the filter.

3. Remove the water tank and tray and
carry them to the sink. Pour any
remaining water into the sink.

4. To remove scale caused by hard
water deposits and to clean the tank
and water tray, these parts can be
either cleaned in a dishwasher or
washed by hand.

5. Inspect the filter each week. If it
becomes hard to the touch, or
shows discoloration (caused by
mineral deposits or mold/mildew
buildup), it should be replaced.
See page 16 for information about
ordering a replacement filter.

6. After cleaning and drying all parts,
follow the instructions on page 6
to reassemble the humidifier. If the
humidifier will not be used for at
least two weeks, see the “Storing
the Humidifier” section.

12

(Cleaning in a dishwasher)

The parts shown on the right are
dishwasher-safe for easy cleaning.
These parts are a transparent smoke
color for easy identification.

NOTES:

• Always wash humidifier parts

separately from dishes.

• Always use a heated water wash
cycle.

• If your dishwasher has a heated dry
cycle, it should be turned OFF.

• Do not use rinse aid while cleaning
humidifier parts.

• ALWAYS remove the filler cap from
the water tank before placing the
tank in the dishwasher.

1. Place the filler cap in the dishwasher’s

silverware basket. This small part
must be secured in the silverware
basket to prevent it from being
damaged by the dishwasher.

2. Place water tank in the dishwasher

with the tank opening facing down if
possible. This position will trap the
least amount of water in the tank.

Filler
Cap

Water
Tank

Water
Tray

Preferred Cleaning Method

Tip!

If the water tank won’t stand up in your
dishwasher, try moving the silverware
basket to another area in the dishwasher
and place the tank in the silverware
basket recess.

13

(Cleaning by hand)

To remove mineral deposits:

1. Partially fill the water tray with a

solution of one gallon water and
8 ounces undiluted white vinegar.

2. Allow to stand for 20 minutes,

then clean all interior surfaces
with a soft brush.

3. Dampen a soft cloth and wipe out

entire tray to remove scale.

4. Rinse thoroughly with clean warm

water to remove any remaining scale
and vinegar/water solution.

To clean the tank:

1. Fill the tank with one gallon of water

and one teaspoon of chlorine bleach.

2. Replace the filler cap, and let the
solution stand for 20 minutes,
swirling it around the tank every few
minutes to wet all inside surfaces.

3. Empty the tank, rinse tank and filler
cap thoroughly with water until no
bleach smell is noticeable. Dry with a
clean cloth or paper towel.

Storing the Humidifier

1. Unplug the humidifier.

2. Empty the water tank and water tray.

3. Discard the filter. DO NOT leave it in

the humidifier. To order a new filter,
see page 16.

4. Follow the cleaning instructions for
weekly maintenance.

5. On models with a manual humidistat,
turn the humidistat to the minimum
setting.

6. Make sure all parts are completely
dry. DO NOT leave any water in the
humidifier when storing it.

7. Place the humidifier in the original
box and store in a cool, dry place.

8. Clean the humidifier and install the
new filter before using it again.

Alternate Cleaning Method

If the humidifier will not be used for at least two weeks:

14

Troubleshooting Guide

The Humidifier Will Not Turn On

• Is the tank filled and properly seated
on the base?

• Is the humidifier plugged into a
powered outlet?

• Is the humidifier turned on?

• Is the desired humidity set lower
than the current room humidity level?
The humidifier turns on automatically
when the desired humidity is higher
than the current room humidity.

The Tank Leaks

• Is the filler cap gasket in place?
If not, press it into the groove
around the tank fill opening. If the
gasket seal is missing or damaged,
call the customer service number
on the cover to order a replacement
gasket. Do not use the humidifier
without the gasket in place.

• Is the filler cap locked tightly? Make
sure that the “LOCKED” arrows line
up with the ridges on the fill neck.

• Is something trapped under the edge
of the rubber seal in the center of the
filler cap? Check for debris under the
edge of the seal, or for damage to
the seal. If the seal is damaged, a
replacement seal can be ordered
by calling the customer service
number on the cover.

The Tank Is Full But the Tray Does Not Fill

• Is the cord or another object trapped
under the tank? Make sure that the
tank is properly seated on the base
and that the power cord is routed
correctly. If the tank will not seat
properly, see “Fan Enclosure or
Tank Does Not Fit on Base.”

The following section provides the solutions to many common problems and
questions. If your humidifier is not working correctly, review these solutions first;
it may save you a phone call. If your problem is still not solved after reviewing
this guide, call our toll-free customer service number, listed on the cover of this
manual.

• Make sure that the cord or other

objects are
not trapped
under the fan
enclosure
or tank.

• Is the cord routed correctly? The

cord should
be pressed
completely
into the cord
exit notch.
Any excess
cord should
be completely
behind the

tabs in the
cord storage compartment, as
shown above.

15

The Filler Cap Is Difficult to Remove

• Sometimes a vacuum can form in
the tank,
especially
if it has not
been seated
on the base
for a long
period of
time. Press
the button
in the center

of the filler cap to relieve the vacuum.

• Apply 100% pure petroleum jelly
to the filler cap gasket. Wipe off
any excess.

Press here

Fan Enclosure or Tank Does Not Fit on Base

Cord
exit
notch

Cord
behind
tabs

Rounded filter

New filter

• New filters are shipped flat and must
be “rounded”

before installation.
Gently pull the filter into a round
shape, being careful not to tear it.
Once the filter is properly rounded,
install it and

lower the fan

enclosure

into place

(as described

on page 6).

16

THREE-YEAR LIMITED WARRANTY

Hamilton Beach/Proctor-Silex, Inc. warrants this appliance to be free from defects in
material and workmanship for a period of three (3) years from the date of original purchase,
except as noted. There is no warranty with respect to the following, which may be supplied
with this appliance: the filter. This warranty extends only to the original consumer purchaser
and does not cover damage from abuse, neglect, use for commercial purposes, or any
other use not found in the printed directions. HAMILTON BEACH/PROCTOR-SILEX, INC.
EXPRESSLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WAR­RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ANY
LIABILITY HEREUNDER IS EXPRESSLY LIMITED TO THE REPAIR OR REPLACEMENT
OF A DEFECTIVE PRODUCT OR AN AMOUNT EQUAL TO THE PURCHASE PRICE PAID
THEREFOR, AND ALL CLAIMS FOR SPECIAL AND CONSEQUENTIAL DAMAGES ARE
HEREBY EXCLUDED. Some states or provinces do not allow this exclusion or limitation of
incidental or consequential losses, so the foregoing disclaimer may not apply to you. If you
have a claim under this warranty, DO NOT RETURN THE APPLIANCE TO THE STORE!
Please call our CUSTOMER SERVICE NUMBER. (For faster service please have model,
series, and type numbers ready for operator to assist you.)

CUSTOMER SERVICE NUMBERS

In the U.S. 1-800-851-8900

In Canada 1-800-267-2826

Web site address: www.hamiltonbeach.com

KEEP THESE NUMBERS FOR FUTURE REFERENCE!

This warranty gives you specific legal rights, and you may also have other legal rights
which vary from state to state, or province to province.

Customer Service

If you have a question about your humidifier, call our toll-free customer service
number. Before calling, please note the model, type, and series numbers and fill
in that information below. These numbers can be found on the back of the fan
enclosure. This information will help us answer your question much more quickly.

MODEL: ______________ TYPE: _______________ SERIES: _________________

Web site address: www.hamiltonbeach.com

8/00

840074800

Replacement Filters:

Humidifier USA Canada Filter
Capacity: Models: Models: Part Number:

2.5 gallons/day 05518 & 05519 05518C & 05519C 05910

3.5 gallons/day 05520 & 05521 05520C & 05521C 05920

HAMILTON BEACH PROCTOR-SILEX,INC.

P

ROCTOR-SILEX CANADA,INC.

263 Yadkin Road

Southern Pines, NC 28387

Picton, Ontario K0K 2T0