Hameg HMO3000, HMO3032, HMO3042, HMO3052, HMO3034 Technical Data Manual

Mixed Signal Oscilloscopes

300 MHz

|

400 MHz | 500 MHz

HMO3000 Series

More information | www.hameg.com 3

up to 500 MHz…

High sensitivity, multi-functionality and a great price –
that‘s what distinguishes the HAMEG HMO3000 oscilloscope series.

Key facts

❙4 GSa /s real time, low noise fl ash A /D converter
❙8 MPts memory, zoom up to 200,000:1
❙MSO functionality included as standard

(HO3508/HO3516 logic probe with 8/16 channels required)
❙Automatically or manually adjustable memory depth
❙Vertical sensitivity up to 1 mV/div.
❙Trigger modes: slope (A/B), pulse width, video, logic,

serial buses (optional), hold-off
❙Serial bus trigger and hardware accelerated decode incl. list view.

Options: I

2

C + SPI + UART/RS-232 (HOO10/HOO11), CAN + LIN (HOO12)
❙28 auto-measurement parameters plus statistics, formula editor, ratio cursor
❙6-digit hardware counter
❙FFT up to 64 kPts (dBm, dBV, V

rms

)
❙Pass/fail test based on masks
❙Automatic search for user-de ned events
❙Display: 12 div. x-axis, 20 div. y-axis (Virtual Screen)
❙2x USB for mass storage, Ethernet/USB dual interface for remote control

HMO 3004 Series, 500 MHz with 4 Channels

Intelligent user interface

To optimize the screen
display, the instrument
shows and hides menus

Precise signal analysis

4 GSamples/s sampling rate
8 MPoints memory

Video

Setup

Intuitive, multi-lingual
user menu

FFT

Superb FFT
functionality

Help

Context-sensitive help

Quick view

At the push of a button
the 16 most important
values of the measured
signal are permanently
updated and displayed

Fan

Maximum noise reduction by

temperature-controlled fan

Zoom

Memory zoom up to
200,000 : 1

Analog channels

Vertical sensitivity of up to
1mV/div.

Bus signal source

To create SPI, I2C, UART
and counter test-signals

Standard MSO functionality

Analyze analog channels plus up to
an additional 16 digital channels

Math

Wide range of programmable
math functions

Display

Superb 16.5 cm (6.5”) LED-backlit

TFT display

2 HAMEG INSTRUMENTS | HMO3000 SERIES

HMO3000 product video:

Scan, click or go to

http://youtube.com/

HAMEGcom

HMO 3000 Series

Application How the HAMEG HMO3000 meets your needs

Engineering lab ❙ Adjustable memory depth

❙ Advanced math functions available as standard, math on math possible
❙ Automeasurement for 28 user-defined parameters

❙ Memory zoom function up to 200,000:1
Analog
circuit design

❙ Low-noise amplifier and A/D converter

❙ 1 mV/div. sensitivity

❙ 50 Ω/1 MΩ input impedance, switchable

❙ Bandwidth upgrades via software options
Embedded
debugging

❙ Mixed signal option (MSO) with 16 logic channels

❙ Serial bus trigger and hardware-accelerated decode

❙ 6-digit hardware counter

❙ Superb FFT functionality
Production
environment

❙ Remote control for automated data acquisition

❙ Pass/fail tests based on user-defined masks with error signal output

❙ Automatic signal measurement at the push of a button

❙ USB/RS-232, Ethernet or GPIB (IEEE 488) interfaces
General
purpose and
education

❙ Fast boot time

❙ Low-noise, intelligent temperature management

❙ Extended display size through Virtual Screen technology

❙ DVI-D output for external display

More information | www.hameg.com 5

Precise Signal Analysis

An excellent sampling rate in combination with a large memory depth is the key

for precise signal analysis. The highly resolved measurement data and the

powerful zoom function expose even minor signal details.

Depending on their requirements users can choose between three 2-channel-

versions and three 4-channel-versions with bandwidths between 300 and
500 MHz.

500 MHz 400 MHz 300 MHz

4 channel

HMO3054 HMO3044 HMO3034

2 channel

HMO3052 HMO3042 HMO3032

4 HAMEG INSTRUMENTS | HMO3000 SERIES

Bandwidth Upgrade

Should your requirements change, then so does the HMO3000, as the 300
and 400 MHz models can be extended to 500 MHz bandwidth via software
upgrades whenever required.

❙For 300 MHz models with options

HOO352 (2 channel) and HOO354 (4 channel).

❙For 400 MHz models with options

HOO452 (2 channel) and HOO454 (4 channel).

Options

HOO352 / HOO354

HOO452 / HOO454

Key facts

Sampling rate (per analog channel) 2 GSa/s

Maximum sampling rate 4 GSa/s

Memory depth per cha nnel 4 MPts.

Maximum memory 8 MPts.

Maximum number of logic ch annels 16

Input impedance 1 MΩ / 50 Ω

V/div. @1 MΩ 1 mV/div. to 5 V/div.

V/div. @50 Ω 1 mV/div. to 1 V/div.

Upgrade at any time

HMO 3000 Series

500 MHz

300 MHz | 400 MHz

300 MHz

>>>

500 MHz

400 MHz

>>>

500 MHz

More information | www.hameg.com 76 HAMEG INSTRUMENTS | HMO3000 SERIES

Always a MSO

Optional: Logic probe HO3508

❙Logic probe HO3508 fi ts to all

HMO series oscilloscopes

(also available as double pack HO3516)
❙No hardware lock to a speci c device
❙8 logic channels available

on each logic probe
❙Signal threshold adjustable

for each logic pod

Specifi cations HO3508

Channels 8

Input impedance 100 kΩ || <4 pF

Max. input frequency 350 MHz

Max. input voltage 40 V (DC + peak AC)

Measuring category CAT I

Cable length approx. 1 m

HAMEG is offering the new HMO3000 series exclusively as a mixed-signal oscilloscope. The great
advantages of these instruments are best illustrated by taking a look at how ADCs (Analog Digital
Converter) or DACs (Digital Analog Converter) are integrated. These transformer modules include

an analog signal on the one side and a digital signal on the other side. As with HAMEG's new
HMO3000 series, MSOs allow developers the assessment of the time component for both signal

types on one monitor. As shown in the image below the latency time of a DAC can be determined

with one simple cursor measurement. Therefore a MSO allows developers to devote their full
attention to the circuit without having to waste energy on the measurement setup.

HAMEG is focusing resolutely on the increasing signi cance of the mixed-signal oscilloscopes.

Consequently, all HAMEG HMO oscilloscopes are full-scale MSOs, even the smaller models with a
bandwidth as low as 70 MHz. As a result, HAMEG customers will not need to speculate if they
should purchase an instrument with or without logic connectors. As the MSO functionality is
invariably included, all instruments correspondingly offer a secure future. It is also unnecessary to

initially activate the mixed-signal functions via software options, as is the case with other suppliers.

The mixed signal functionality is always included in the HMO3000

series with no software option being necessary to unlock it.

14 bit DAC signal change

HAMEG logic probes

are not linked to a speci c

instrument serial number.
This allows their use with all
digital HAMEG oscilloscopes
in the HMO series.

Mixed Signal

Mixed Signal

More information | www.hameg.com 98 HAMEG INSTRUMENTS | HMO3000 SERIES

Frequency Analysis

FFT functionality

FFT functionality

Due to the outstanding FFT functionality of the HMO series oscilloscopes signals can also be analysed in
the frequency domain with up to 65,536 points. Additional practical tools such as cursor measurement as

well as peak-detect-functions are also available. They allow engineers to complete their analysis signicantly

faster, also in the frequency domain.

Figure 5

Easy analysis in frequency domain

Quite often the distortion of input signals cannot be
detected with the naked eye. For instance, the sine

wave signal displayed in gure 1 appears to be
undistorted. Only the frequency spectrum (gure 2)

- available with just one touch of a button - clearly
displays additional harmonics that occur as
harmonic oscillations for multiples of the basic
frequency.

For non-periodic input signals most instruments
offer the option to trigger the spectrum at just the
right moment to then check it in “STOP” mode
at a later time. However, at that point, many
oscilloscopes with FFT functionality calculate the
spectrum only once and store the result in the
memory. The base time signal will no longer be used
for the calculation. Consequently, an investigation
of all parts of the signal will no longer be possible.

HMO series oscilloscopes work differently: Since
FFT is also active for previously stored signals, it is
possible to subsequently analyze any sections of
those signals captured in single shot mode or stop
mode with an adjustable window width. Figure 3
shows a sine burst signal in the time domain.
Pushing the FFT button will switch the oscilloscope
into the frequency domain. Users can choose
between various measurement windows like the

„rectangular“ type that has been used in gure 4.

Although this window type captures frequencies at
a high degree of accuracy, it is also accompanied
by more noise. In order to suppress this disturbing
interference users can for instance choose the
Hanning window. The impact on the spectrum is

visible in gure 5 (see device screen).

Figure 1: A sinusoid signal that at rst sight appears undistorted Figure 2: The frequency spectrum exposes the signal distortion Figure 3 Figure 4

More information | www.hameg.com 1110 HAMEG INSTRUMENTS | HMO3000 SERIES

Serial Bus Analysis

I2C, SPI, CAN or LIN – in terms of interaction with the outside world for
embedded systems, it is safe to say that these are the most commonly used
communication protocols. The new HMO3000 series by HAMEG Instruments
offers you hardware-accelerated signal triggering and decoding for all of these
protocols. You can upgrade your instrument via software licence keys with those
functions required to develop your application:

❙HOO10: Analysis of I

2

C, SPI and UART/RS-232 signals on analog and logic

channels

❙HOO11: Analysis of I

2

C, SPI and UART/RS-232 signals on all analog channels

❙HOO12: Analysis of CAN and LIN signals on analog and logic channels

Serial bus trigger types:

❙I2C: Start, Stop, ACK, nACK,

Address/Data

❙SPI: Start, End, Serial Pattern

(32Bit)

❙UART/RS-232: Startbit,

Frame Start, Symbol, Pattern

❙LIN: Frame Start, Wake Up,

Identier, Data, Error

❙CAN: Frame Start, Frame

End, Identier, Data, Error

SPI bus trigger setup CAN bus conguration

I

2

C bus hex decoding on the analog

channel

I

2

C bus ASCII und binary

CAN bus list display

HEX decoded CAN bus signal

HOO10 / HOO11

SPI / I2C / UART/RS-232 bus
analysis for all oscilloscopes
of the HMO series

HOO12

CAN / LIN bus analysis
for all oscilloscopes of the
HMO series

Application

HMO3004 series 4 channel mixed signal oscilloscope
HMO3002 series 2 channel mixed signal oscilloscope
HMO3032 [HMO3034] 300MHz
HMO3042 [HMO3044] 400MHz
HMO3052 [HMO3054] 500MHz

Firmware: ≥ 5.0

Display

Display: 16.5 cm (6.5") VGA Color TFT
Resolution: 640 x 480 Pixel
Backlight: LED 500 cd / m

2

Display area for traces: 50 Pts / div.
without menu 400 x 600 Pixel (8 x 12 div.)
with menu 400 x 500 Pixel (8 x 10 div.)
Color depth: 256 colors
Intensity steps per channel: 0 to 31
Channel display: False color, inverse brightness
Bus display: up to 2 busses, parallel busses, serial busses

(option), decoding of the bus values in ASCII,

binary, decimal or hexadecimal format; Table

view of the decoded data

Virtual Screen 20 div. vertical for all Math-, Logic-, Bus- and

Reference Signals

LED brightness: 2 steps

Vertical System

Channels:

DSO mode CH 1, CH 2 [CH 1 to CH 4]
MSO mode CH 1, CH 2, LCH 0 to 15 (logic channels)

with 2 x Option HO3508

Auxiliary input: Front side [Rear side]

Function External Trigger
Impedance 1 MΩ || 14 pF ±2 pF
Coupling DC, AC

Max. input voltage 100 V (DC + peak AC)

XYZ-mode: All analog channels on individual choice
Invert: CH 1, CH 2 [CH 1 to CH 4]
Y-bandwidth (-3 dB): 300/400/500 MHz (5 mV to 5 V) /div.

300 MHz: 180 MHz (1mV, 2 mV)/div.

400 / 500 MHz: 200 MHz (1mV, 2 mV)/div.
Lower AC bandwidth: 2 Hz
Bandwidth limiter (switchable): approx. 20 MHz
Rise time (calculated): 300 MHz: < 1.166 ns

400 MHz: < 0.875 ns

500 MHz: < 0.7 ns
DC gain accuracy: 2 % of full scale

Input sensitivity: 12 calibrated steps

CH 1, CH 2 [CH 1 to CH 4] 1mV/div. to 5V/div. (1–2–5 Stepping)

Variable Between calibrated steps

Inputs CH 1, CH 2 [CH 1 to CH 4]:

Impedance 1 MΩ II 13 pF ±2 pF (50 Ω switchable)
Coupling DC, AC, GND

Max. input voltage 1 MΩ: 200 V

p

, derates at 20 dB/Decade to

5 V

rms

above 100 kHz

50 Ω: < 5 V

rms

, max. 30 V

p

Measuring circuits: Measuring Category 0
Position range: ± 8 divs
Offset control:

1 mV, 2 mV ± 0.2 V - 8 div. * sensitivity
5 mV to 20 mV ± 1 V - 8 div. * sensitivity
50 mV ± 2.5 V - 8 div. * sensitivity
100mV, 200mV ±20V - 8div. * sensitivity
500 mV to 5 V ± 50 V - 8 div. * sensitivity

Logic channels: With Option HO3508 / HO3516

Select. switching thresholds TTL, CMOS, ECL, 2 x User -2 V to +8 V
Impedance 100 kΩ || < 4 pF
Coupling DC

Max. input voltage 40 V (DC + peak AC)

Triggering

Trigger modes:

Auto Triggers automatically even when no trigger

event occurs for a certain time
Norm Always triggers when a trigger event occurs
Single Triggers once on a trigger event

Trigger display: LED
Trigger sensitivity:

Intern ≥5 mV / div.: 0.8 div.

≥2 mV / div. to <5 mV / div.: 1div.

<2 mV / div.: 1.5 div.
Ext. trigger via Auxiliary Input [Aux. Input rear side]
Ext. Sensitivity 0.5 V to 10 V

pp

Trigger level range:

With auto level Adjustability of the level between the peak

values of the signal
Without auto level -8 div. to +8 div.
External -5 V to +5 V

Trigger types:

Slope:

Slope direction Rising, falling, both
Sources CH 1, CH 2, Line, Ext [CH 1 to CH 4, Line, Ext.]

Coupling

Auto level Adjustability of the level between the peak

values of the signal, 5 Hz to 300/400/400 MHz

AC 5 Hz to 300/400/400 MHz
DC 0 to 300/400/400 MHz

HF 30 kHz to 300/400/400 MHz
LF 0 kHz to 5 kHz, selectable for DC, Auto level
Noise rejection (low-pass) 100 MHz, selectable for DC, AC, Auto level

Pulse width:

Polarity Positive, negative
Functions ti>t, ti<t, ti=t, ti/=t, t1<ti<t2, not (t1<ti<t2)
Pulse duration 16 ns to 8.589 s, resolution 4 ns/1 µs

Video Pos./neg. sync. impulse

Standards PAL, SECAM, NTSC, PAL-M, SDTV 576i,

HDTV 720p, HDTV 1080i, HDTV 1080p

Fields Upper, lower, both
Line All, line number selectable
Source CH 1, CH 2, Ext. [CH 1 to CH 4]

Logic:

Logic functions AND, OR, TRUE, FALSE, with or without eval-

uation of the duration of the logic operation

Duration functions ti>t, ti<t, ti=t, ti/=t, t1<ti<t2, not (t1<ti<t2),

Timeout
Duration 4 ns to 1 s
Source LC0 to 15
State LC0 to 15 X, H, L

Serial Busses: (Options)

I

2

C Start, Stop, ACK, NACK, Address/Data
SPI Start, End, Serial Pattern (32Bit)
UART/RS-232 Startbit, Frame Start, Symbol, Pattern
LIN Frame Start, Wake Up, Identifier, Data, Error
CAN Frame Start, Frame End, Identifier, Data, Error

Trigger Holdoff: 50 ns to >10 s
2

nd

Trigger (B):
Type Slope trigger
Slope direction Rising or falling
Min. signal height 0.8 div.
Source CH 1, CH 2, Ext. [CH 1 to CH 4]

Coupling (source B/=A): DC, HF, NR
Coupling (source B=A): see trigger A
Level (source B/=A): -8 div to +8 div. (adjustable separately by A)
Level (source B=A): see level A

Frequency range 0 MHz to 300 / 400 / 500 MHz
Operating modes:

Time based 16 ns to 8.589 s, resolution 4 ns/1 µs
Event based 1 to 2

16

Horizontal System

Domain representation: Time, Frequency (FFT), Voltage (XY)
Representation Time Base: Main-window, main- and zoom-window
Memory Zoom: Up to 200,000:1
Time Base:

Accuracy 15 ppm

Technical Data

Technical Data

Recommended accessories:

HOO10 Analysis of I

2

C, SPI and UART/RS-232 signals on analog

and logic channels

HOO11 Analysis of I

2

C, SPI and UART/RS-232 signals on all analog

channels

HOO12 Analysis of CAN and LIN signals on analog and logic channels

for two buses

HO3508 Active 8 channel logic probe

HO3516 2 x HO3508, active 8 channel logic probes

HO720 USB-device/RS-232 dual-interface card
HO740 IEEE-488 (GPIB) interface card, galvanically isolated
HZ46 4 RU 19" Rackmount kit
HZ99 Carrying case for protection and transport

HZ100 Differential probe 20:1/200:1
HZ115 Differential probe 100:1/1,000:1

HZ355 500 MHz passive probe 10:1 with automatic identification

HZ355DU Upgrade from 2 x HZ350 to 2 x HZ355

HZO20 High voltage probe 1000:1 (400 MHz, 1000 V

rms

)

HZO30 1 GHz active probe (0.9 pF, 1 MΩ, including many accessories)
HZO40 Active differential probe 200 MHz (10:1, 3,5pF, 1 MΩ)
HZO41 Active differential probe 800 MHz (10:1, 1pF, 200 kΩ)
HZO50 AC/DC current probe 30 A, DC to 100 kHz
HZO51 AC/DC current probe 100/1000 A, DC to 20 kHz

Accessories included:

HO730 Ethernet/USB dual-interface card, Line cord, printed operating

manual, 2/4 probes (amount=number of channels), 10:1 with attenuation ID
(HZ350 400/300 MHz, HZ355 500 MHz), software-CD

HO730

Built-in Ethernet/USB
dual-interface card

Printed operating manual

and software-CD

HZ350

400 MHz passive probe

(for 400/300 MHz oscilloscop es)

HZ355

500 MHz passive probe

(for 500 MHz oscilloscopes)

More information | www.hameg.com 1312 HAMEG INSTRUMENTS | HMO3000 SERIES

Accessories included:

HO730 Ethernet/USB dual-interface card, Line cord, printed operating

manual, 2/4 probes (amount=number of channels), 10:1 with attenuation ID
(HZ350 400/300 MHz, HZ355 500 MHz), software-CD

HO730

Built-in Ethernet/USB
dual-interface card

Printed operating manual

and software-CD

Recommended accessories:

HOO10 Analysis of I

2

C, SPI and UART/RS-232 signals on analog

and logic channels

HOO11 Analysis of I

2

C, SPI and UART/RS-232 signals on all analog

channels

HOO12 Analysis of CAN and LIN signals on analog and logic channels

for two buses

HO3508 Active 8 channel logic probe

HO3516 2 x HO3508, active 8 channel logic probes

HO720 USB-device/RS-232 dual-interface card
HO740 IEEE-488 (GPIB) interface card, galvanically isolated
HZ46 4 RU 19" Rackmount kit
HZ99 Carrying case for protection and transport

HZ100 Differential probe 20:1/200:1
HZ115 Differential probe 100:1/1,000:1

HZ355 500 MHz passive probe 10:1 with automatic identification

HZ355DU Upgrade from 2 x HZ350 to 2 x HZ355

HZO20 High voltage probe 1000:1 (400 MHz, 1000 V

rms

)

HZO30 1 GHz active probe (0.9 pF, 1 MΩ, including many accessories)
HZO40 Active differential probe 200 MHz (10:1, 3,5pF, 1 MΩ)
HZO41 Active differential probe 800 MHz (10:1, 1pF, 200 kΩ)
HZO50 AC/DC current probe 30 A, DC to 100 kHz
HZO51 AC/DC current probe 100/1,000 A, DC to 20 kHz

HZ350

400 MHz passive probe

(for 400/300 MHz oscilloscop es)

HZ355

500 MHz passive probe

(for 500 MHz oscilloscopes)

Aging ±5 ppm/year

Refresh operating modes 1 ns/div. to 20 ms/div.

Roll operating modes 50 ms/div. to 50 s/div.

Deskew: -62,5 ns to +61,5 ns

Step size 500 ps

Search functions: Slope, Pulse, Peak, Rise-/Falltime, Runt

Marker: up to 8 user definable marker for easy naviga-

tion; automatic marker function based on

search criteria

Digital Storage

Sampling rate: 2 x 2 GSa/s, 1 x 4 GSa/s

[4 x 2 GSa/s, 2 x 4 GSa/s]
Logic channels: 16 x 1 GSa/s

Resolution (vertical): 8 Bit, HiRes 10 Bit

Memory: 2 x 4 MPts [4 x 4 MPts], 1x 8 MPts [2 x 8 MPts]

Operation modes: Refresh, Average (1024), Envelope, Peak-

Detect (500ps), Filter, Rol (free run/triggered

from time base 50 ms/div. and slower),
HiRes

Interpolation: CH 1 to CH 4: Sinx/x, Pulse, Linear;

LC0 to 15: Pulse

Persistence: Off, 50 ms to ∞

Delay pretrigger: 0 to 4 Million x (1/samplerate), Interlaced x2

posttrigger 0 to 8,59 Billion x (1/samplerate)

Display refresh rate: Up to 4,800 waveforms/s

Display: Dots, vectors (interpolation), ‘persistence’

Operation/Measuring/Interfaces

Operation: Menu-driven (multilingual), Autoset,

help functions (multilingual)

Frequency counter:

0.5 Hz to 300/400/500 MHz 6 Digit resolution

Accuracy 15 ppm

Aging ±5 ppm/year

Auto measurements: V

pp

, Vp+, Vp-, V

rms

, V

avg

, V

top

, V

base

, amplitude,
phase, frequency, period, risetime 80 / 90 %,
falltime 80 / 90 %, pos./neg. pulse width, pos./
neg. duty cycle, standard deviation, delay,
pos./neg. edge count, pos./neg. pulse count,
trigger period, trigger frequency

Statistic Min., max., mean, standard deviation,

number of measurements for up to
6 Functions simultaneously

Cursor measurements: ∆V, ∆t, 1/∆t (f), V to GND, Vt related to Trigger

point, ratio X and Y, pulse count, edge count,
peak to peak, peak+, peak-, mean value,
RMS value, standard deviation, rise time,
duty cycle

Application memory: 8 MByte for references, device settings and

formulars

Interface:

Internal 2x USB-Host (type A) (1x front side, 1x rear

side), mass storage (FAT16/32)

Exchangeable HO730 Dual-Interface Ethernet/USB-Device

(type B)

Video OUT: DVI-D (480 p, 60 Hz) for external display,

HDMI compatible

Trigger OUT: BNC (rear side), Modes: Trigger, Mask

Optional: USB-Device/RS-232 Dual-Interface (HO720),

IEEE-488 (GPIB) (HO740)

Mathematic functions

Quickmath: ADD, SUB, MUL, DIV

Editor for formula sets: Max. 5 formulas per formula set

Label for: Math. memories and formula set

Sources: All channels and math. Memories,

constants
Targets: Math. memories

Functions: ADD, SUB, 1/X, ABS, MUL, DIV, SQ, POS,

NEG, INV, SQR, MIN, MAX, LOG

10

, LN,
Integral, Differential, High-pass filter,
Low-pass filter

Display: Up to 4 math. memories with label

Mask test: Signal test (pass/fail) based on previously

defined mask

Quickview: Display of V

p+

, Vp-, RMS value, rise time,

fall time

General Information

Probe ADJ Output: 1 kHz/1MHz square wave signal

approx. 0,2V

pp

(ta <4 ns)

Bus Signal Source (4Bit): SPI, I

2

C, UART, retangle, 4Bit counter,

4 Bit random pattern

Internal RTC (Realtime clock): Date and time for stored data

Line voltage: 100 V to 240 V, AC 50 Hz to 60 Hz, CAT II

Power consumption: Max. 70 [90] W

Protective system: Safety class I (EN61010-1), CSA (pending)

Operating temperature: +5 °C to +40 °C

Storage temperature: -20 °C to +70 °C

Rel. humidity: 5 % to 80 % (non condensing)

Theft protection: Kensington Lock

Dimensions (W x H x D): 285 x 175 x 220 mm

Weight: 3.6 kg

All data valid at 23°C after 30 minute warm-up.

Recommended Accessories

HO720

USB-device/RS-232 dual­interface card

HZ99

Carrying case for
protection and transport

HZO20

High voltage probe 1000:1
(400 MHz, 1000 V

rms

)

HZO30

1 GHz active probe

(0.9 pF, 1 MΩ, including many accessories)

HZO40

Active differential probe

200 MHz (10:1, 3.5 pF, 1 MΩ)

HZO41

Active differential probe

800 MHz (10:1, 1 pF, 200 kΩ)

HZO50

AC/DC current probe 30 A,
DC to 100 kHz

HZO51

AC/DC current probe
100/1000 A, DC to 20 kHz

HZ115

Active differential
high voltage probe

HZ355

500 MHz passive probe 10:1

with automatic identication

HZ355DU

Upgrade from
2 x HZ350 to 2 x HZ355,

only available when
purchasing a HMO3000
(300 MHz / 400 MHz
models)

HO740

IEEE-488 (GPIB) interface
card, galvanically isolated

HZ46

4 RU 19” rackmount kit

Accessories

HMO compact series

Bandwidth 200 MHz 150 MHz 100 MHz 70 MHz

Model: 4 channel

2 channel

HMO2024
HMO2022

HMO1524
HMO1522

HMO1024
HMO1022

HMO724

HMO722
Sampling rate (per analog channel) 1 GSa/s

Maximum sampling rate 2 GSa/s

Memory depth per channel 1 MPts.

Maximum memory 2 MPts.

Max number of logic channels 8

Input impedance 1 MΩ / 50 Ω 1 MΩ

V/div. @ 1 MΩ 1 mV/div. to 10 V/div.

V/div. @ 50 Ω 1 mV/div. to 1 V/div. n/a

DC-offset ± 0.2V to ± 100V –

Component tester ■

14 HAMEG INSTRUMENTS | HMO3000 SERIES

HMO Compact Series

8 different models in a compact design with bandwidths from 70 to 200 MHz

available with 2 or 4 channels. The mixed signal functionality is always included

in the HMO compact series with no software option being necessary to unlock it.

Key facts

❙2 GSa/s real time, low noise fl ash A/D converter
❙2 MPts memory, zoom up to 50,000:1
❙ MSO functionality included as standard

(HO3508 logic probe with 8 channels required)
❙Component tester for capacitors, inductors and semiconductors
❙Vertical sensitivity up to 1 mV/div.
❙ Trigger modes: slope (A/B), pulse width, video, logic, serial buses (optional)
❙Serial bus trigger and hardware accelerated decode incl. list view.

Options: I

2

C + SPI + UART/RS-232 (HOO10/HOO11), CAN + LIN (HOO12)
❙ 28 auto-measurement parameters plus statistics, formula editor, ratio cursor
❙6-digit hardware counter
❙FFT up to 64 kPts (dBm, dBV, V

rms

)
❙ Pass/fail test based on masks
❙Automatic search for user-de ned events
❙Display: 12 div. x-axis, 20 div. y-axis (Virtual Screen)
❙2x USB for mass storage, RS-232/USB dual interface for remote control

200 MHz | 150 MHz | 100 MHz | 70 MHz

HMO compact series

Small foot print Bus signal sourceBuilt-in component tester

From entry level to
high performance.

Oscilloscopes from
the T&M expert.

Fast operation, easy to use, precise measurements –
that’s Rohde & Schwarz oscilloscopes.

R&S®RTO: high performance (Bandwidths: 600 MHz to 4 GHz)
R&S®RTM: upper midrange (Bandwidths: 350 MHz and 500 MHz)
HMO3000: midrange (Bandwidths: 300 MHz to 500 MHz)
HMO Compact: value range (Bandwidths: 70 MHz to 200 MHz)

All Rohde & Schwarz oscilloscopes incorporate time domain,
logic, protocol and frequency analysis in a single device.

Take the dive at www.scope-of-the-art.com

value-instruments.com

HAMEG Instruments GmbH
Industriestr. 6 | 63533 Mainhausen | Germany | Phone [phone]

www.hameg.com

R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG
HAMEG Instruments® is a registered trademark of HAMEG
Instruments GmbH | Trade names are trademarks of the owners
11 / 2013 | © HAMEG Instruments GmbH | 4A-D000-0430
Printed in Germany | Subject to change without notice