Page 1
PLATINUM
SPRINT 500
(HT050700)
QUICK START GUIDE
Page 2
LIMITED WARRANTY
Lockin Pty Ltd trading as Haltech warrants the HaltechTM Programmable Fuel Injection System to be
free from defects in material or workmanship for a period of 12 months from the date of purchase.
Proof of purchase, in the form of a bill of sale or receipted invoice, which indicates that the product is
within the warranty period, must be presented to obtain warranty service. Lockin Pty Ltd trading as
Haltech suggests that the purchaser retain the dealer’s dated bill of sale as evidence of the date of
retail purchase.
If the HaltechTM Programmable Fuel Injection System is found to be defective as mentioned above, it
will be replaced or repaired if returned prepaid along with proof of purchase. This shall constitute the
sole liability of Lockin Pty Ltd trading as Haltech.
To the extent permitted by law, the foregoing is exclusive and in lieu of all other warranties or
representations, either expressed or implied, including any implied warranty of merchantability or
fitness. In no event shall Lockin Pty Ltd trading as Haltech, be liable for special or consequential
damages.
IGNITION WIRING WARNING
This system is capable of controlling either Auto-Dwell (also known as intelligent or smart ignitors)
which have in-built dwell control or ECU Dwell ignitors (also known as dumb ignitors or Constant
Charge Ignitors), which contain no such control. This allows standard ignitors to be used in many cases.
Auto-dwell ignitors are commonly found on early EFI engines with electronic ignition.
ECU-dwell ignitors are commonly found in modern ECU controlled ignition systems.
Most standard ignitors are ECU Dwell.
It is very important to set the system up to match the type of ignitor used!.
In the ignition set-up page the setting should be:
To control Auto-dwell ignitors set up as “Constant Duty”
To control ECU-dwell ignitors set up as “Constant Charge”
If the wrong setting is applied, damage to the ignition system may occur.
Burning out ignitors due to wrong set-up will not be regarded as Warranty!
Please ensure all power supplies are disconnected before commencing any wiring.
Failure to follow all the warnings and precautions in this manual can lead to damage to
engine components and may possibly void your warranty. Incorrect setup of the ECU can
also lead to damaged engine components.
Damaged components due to incorrect setup will not be regarded as warranty repairs.
GENERAL INSTALLATION WARNING
Avoid open sparks, flames or operation of electrical devices near flammable substances.
Always disconnect the battery cables when doing electrical work on your vehicle.
Do not charge the battery with a 24 Volt truck charger or reverse the polarity of the battery
or any charging unit. Do not charge the battery with the engine running as this could
expose the ECU to an unregulated power supply that could destroy the ECU and other
electrical equipment.
All fuel system components and wiring should be mounted away from heat sources,
shielded if necessary and well ventilated. Disconnect the Haltech ECU from the electrical
system whenever doing any arc welding on the vehicle by unplugging the wiring harness
connector from the ECU.
After completing the installation, make sure that there are no fuel leaks, and no wiring
left un-insulated in case a spark or short-circuit occurs and causes a fire. Also make sure
that you follow all proper workshop safety procedures. If you're working underneath
a jacked-up car, always use safety stands!
Page 3
PLATINUM SPRINT 500
Quick Start Guide
Congratulations on purchasing a Haltech Engine Management System.
This fully programmable product opens the door to virtually limitless performance
modification and tuning of your vehicle. Programmable systems allow you to extract
all the performance from your engine by delivering precisely the required amount
of fuel and ignition timing that your engine requires for maximum output under all
operating conditions.
This quick start guide will walk you through installation of a Haltech ECU into a
vehicle. This guide is accompanied by the full service manual located on the
software CD provided with the ECU that you or your tuner will need to refer to
before completing your installation and configuration. The Manual can also be
downloaded from the Haltech website www.haltech.com
Installation
Air Temperature Sensor
The sensor should be mounted to provide the best representation of the actual
temperature of the air entering the combustion chamber, i.e. after any turbo or
supercharger, and intercooler, the optimum position being the intake pipe before the
throttle. The sensor needs to be in the moving air stream to give fast response times
and reduce heat soak effects.
The air temp sensor plug is labeled with the letters A and B and should be wired
with the signal wire (Grey) to pin B and signal ground wire (Black/White) to pin A
Figure 1– Air Temperature Sensor and Terminations
Page 4
Coolant Temperature Sensor
The coolant temperature sensor is designed to screw into a threaded hole and
protrude into the engine coolant stream. For air-cooled engines, the sensor can be
embedded directly into the engine block or used to sense oil temperature.
Locate a suitable position on the engine which will allow the hole and thread to be
drilled and tapped, and which gives access to the coolant stream. The sensor
should be mounted before the thermostat in the coolant circuit. Since most engines
have existing temperature sensor holes, it is often possible to mount the Haltech
sensor in one of these holes.
The coolant temp sensor plug is labeled with the letters A and B and should be
wired with the signal wire (violet) to pin B and sensor ground wire (black/white) to pin A.
Figure 2 – Coolant Temperature Sensor and Terminations
Throttle Position Sensor (TPS)
Your engine may have a Throttle position sensor already fitted and it is often
possible to make use of this TPS. The Haltech supplied TPS has a resistance
value ranging from 0 to 10k ohms. The resistance value of the installed TPS does
not have to be the same, since the ECU uses a throttle calibration function to
determine the position of the throttle, based on the signal received from the TPS.
Be sure to wire the TPS so that the ECU sees a lower value when at zero throttle
than at full throttle.
Note: Make sure that the axis of rotation of the shaft is exactly aligned with the axis
of rotation of the sensor, otherwise some binding may occur. Also, do not use the
TPS as a throttle stop. In either case, the TPS will be damaged.
Figure 3 – Throttle Position Sensor
Page 5
MAP Sensors
The Platinum Sprint 500 ECU's are fitted with an internal MAP sensor rated to 22psi
(150 kPa). Connect the internal sensor to the inlet manifold* via vacuum hose to the
external fitting on the ECU.
* Tap into a high point on the inlet manifold to avoid fuel entering the vacuum line,
as damage to the sensor will occur.
Figure 4 – Internal Map Sensor Fitting
Alternatively an external MAP sensor can be fitted via the harness allowing higher
manifold pressures.
The External MAP sensor when used are usually mounted high on the engine bay
firewall or inner guard using two screws and with the hose nipple facing outwards.
Connect the sensor to the inlet manifold via a short length of vacuum hose and fasten
with either hose clamps or nylon cable ties. Connect the sensor to the main wiring
harness using the appropriate plug and harness branch. Avoid mounting the sensor
below the level of the fuel injectors, because fuel may collect in the vacuum hose and
run down into the sensor. The sensor assembly is weatherproof but it is good practice to
mount the sensor in a protected position away from moisture and heat.
Haltech can supply 1 – 5 Bar Map sensors depending on your application,alternatively
OEM map sensors can be used as long as you have the calibration information to
calibrate the sensor in the ECU Manager Software.
Figure 5 – Manifold Absolute Pressure Sensor and harness Termination
Page 6
Crank and Cam Position Sensors (Trigger and Home)
HALL EFFECT SENSOR
+12 V
SIGNAL (+)
GRO U ND
NO T CON NECTED
4 CO RE TR I GGER O R HO M E
CABLE FR O M EC U
REL UCT O R SENSO R
SIGNAL (+)
NO T CON NECTED
4 CORE T R IGGER O R H O M E
CABLE FRO M EC U
SIGNAL (-)
NO T CON NECTED
1234
5678
Device
1
Terminating
Resistor
Required
Device
2
Terminating
Resistor
Not Required
Device
3
Terminating
Resistor
Not Required
Device
4
Terminating
Resistor
Required
CAN BUS
Pin # Function
1 Ground
2 120 Ohm Terminating Resistor Loop
3 CAN LO
4 12V Out
5 Reserved
6 120 Ohm Terminating Resistor Loop
7 CAN HI
8 Reserved
The Crank and Cam Position sensors are required so that the ECU has the necessary
information available to it to determine engine speed and position at any point in time.
Generally 2 sensors are required - a cam position and crank position.
However many cars will have just a cam position sensor that is capable of giving the ECU
enough information to run the engine correctly. Vehicles that have a crank position
sensor only are not capable of determining the difference between compression
stroke and exhaust stroke and therefore are not suitable for sequential fire
applications. In this case a cam position sensor may need to be added for the ECU
to determine if the engine is on compression or exhaust stroke.
There are generally 2 types of trigger signal:
● Hall effect signal (0-5v digital square wave signal)
Generally a hall effect sensor will require a power supply (could be 5V, 8V or
12V), a ground and have a signal wire. Most hall effect sensors have 3 wires.
● Reluctor signal (analogue style signal).
This type of Sensor will generally only have two wires, Signal Positive (+)
and Signal Negative ( - )
Figure 6 – Hall Effect Sensor Wiring
*
*
*Please note: Red and Blue wires must
be insulated to avoid shorting
Figure 7 – Reluctor Sensor Wiring
Page 7
Fuel Pumps
85 87 87
86 30
TO 12V IGNITION SUPPLY
TO - TRIGGER FROM ECU
TO FUEL PUMP + TERMINAL
TO 12V SUPPLY
FUEL PUMP
+
_
TO GROUND
VIA FUEL PUMP FUSE
FUSE
POSITIVE SWITCHED
FUEL PUMP CONTROL
12V FUEL PUMP RELAY
The Black / Yellow wire is used to operate the fuel pump relay. When the Haltech ECU
wants to operate the fuel pump it will close the fuel pump relay which will supply the
fuel pump with 12V From the Battery.
Figure 8- Fuel Pump Wiring
Fuel Pumps continued
It is important that the fuel pump is capable of the correct fuel pressure at full
power, otherwise the engine could be damaged due to a lean fuel mixture. For
example, a 500hp engine requires approximately 210lb/hr for a petrol engine.
The fuel pump must always be mounted lower than the outlet of the fuel tank or
surge tank. Ensure that all care is taken to keep fuel cool. A change in fuel
temperature will change the air/fuel ratio because as fuel temperature increases its
density decreases.
WARNING!
Fuel Injectors
The Platinum Sprint 500 is designed to be used with high impedance injectors only.
Injector impedance can be checked using a multimeter. Injector impedance must be
greater than 8 Ohms, if injectors are used that are less than 8 Ohms, excessive current
draw will cause the ECU to cease firing all injector outputs above 1500 RPM.
Fuel injectors are each wired with a 12V supply with the ground being supplied
through the ECU, it is recommended that the supply for the Injectors be wired as
shown in the appendix of this guide, incorporating an injector relay.
The wires labeled as the injector wires will provide the ground to each injector.
When wiring for sequential injection, fuel injectors should be wired with inj 1 output to
cylinder 1, inj 2 output to cylinder 2 and so on. The injector firing sequence will be set
in the software via the firing order found on the advanced tab of the main setup page.
If semi-sequential injection mode is used the injection sequence will always be inj 1,
Inj 2, inj 3, inj 4 etc regardless of the firing order set in the software.
Always ensure fuel injector sizing is correct for your application and does not
exceed approximately 80% duty cycle for safe operation.
If low impedance injectors are used, an optional Injector Ballast Resistor Box must be
purchased and installed. Order as Haltech Part # HT020600
Page 8
Ignition Outputs
1. COIL NEGATIVE #1
2. CHASSIS GROUND
3. N/A
4. +12V IGNITION
5. ECU IGNITION OUTPUT #1
6. N/A
7. N/A
HALTECH
HECU1
7 6 5 4 3 2 1
+
-
+12 V S WI TCHE D G RO UND
Haltech HECU1 Pino ut
HALTECH 1 CHANN EL IGNIT ION MODULE
HALTECH
ECU
IGN 1
COIL # 1
+
-
+12 V SW ITC HE D
GRO UND
HALTECH
ECU
IGN 1
COIL # 1
CDI UNIT
The Platinum Sprint 500 ECU cannot control the ignition coils directly.
Some sort of ignition amplifier such as a power transistor, Haltech ignition module or high
intensity spark unit (CDI unit eg MSD 6A, crane HI6, M&W pro12 etc) must be used
to interface the ECU with the coils. This ignition module supplies the ground to the
coil only when the ECU directs it to – each coil also requires a 12V source (with the
exception of CDI units where the 12V will often come from the CDI unit itself).
Many factory cars will have ignition modules external to the ECU.
These factory modules can be used in conjunction with the Platinum Sprint 500 ECU.
The ignition output wires from the Platinum Sprint 500 wire harness should be used to trigger
the ignition amplifier – when wiring the ignition amplifier ensure that the system is
wired in cylinder order for direct fire ignition setup or in order of the outputs for waste spark
setup. (ie Ign 1 will fire first, then Ign 2 will fire next etc until the last ignition channel is reached
regardless of engine firing order.)
Figure 10 – Ignition Wiring Using CDI Unit
Figure 9 – Ignition Wiring using Haltech Ignition Module
Page 9
Digital Pulsed Outputs (DPO)
The Platinum Sprint 500 ECU has 4 digital outputs.
The first two outputs are preset to the Tacho and Thermofan functions and the
remaining two outputs are user configurable.
Digital Pulsed outputs are capable of outputting pulsed waveforms with varying duty
and frequency. DPO's can be used to control various devices such as thermo fans,
shift lights, water injection solenoids ,intercooler fans etc.
When a Digital Pulsed output is activated by the ECU the output will switch to ground.
Solenoid valves and shift lights etc can be run directly from the output, however
high current devices such as thermo fans and additional fuel pumps must be activated
through a relay. This way the DPO is only switching a relay and not a high current draw
device.
Digital Pulsed Outputs are limited to 800mA Max current draw.
Digital Pulsed Inputs (DPI)
Digital Pulsed Inputs are capable of accepting pulsed input information such as for a
road speed sensor. These inputs measure the time periods between the pulses and can
process this information to provide quantities such as road speed.
High Tension Leads (spark plug leads) / Capacitive Discharge Ignition Units (CDI )
High tension leads and CDI units can cause significant noise or interference on the ECU
wiring.
Keep all ignition wires a minimum of 100mm from any other wires and ECU
components. If ignition wires must be crossed, ensure wires cross ignition leads at right
angles. Keep power and grounding points separate to those used for ECU.
Wire connections
When using crimp connectors ensure that the correct crimping tool is used – if in
doubt do a pull test on a crimp connector, the wire should break before the wire
pulls out of the crimp. Terminal soldering can weaken a connection and should only
be used as a last resort. If solder joints are used, ensure joints are well isolated
from movement as solder joints are prone to fracture.
When splicing 2 wires it is preferable to use a crimp splice – again if using a solder
joint, ensure joint is limited in its range of possible movement as solder joints are
prone to fracture. Always use heatshrink sleeving to insulate wires and provide
Page 10
Powering up the ECU
The Platinum Sprint 500 requires 12VDC to operate.
Please connect both the Red and Red/White cables to a switched +12VDC supply within the
vehicle. This is best achieved on a vehicle with an existing wiring harness by wiring both these
inputs to the output of the Engine Control Relay via an inline 10A fuse.
Please do not connect these cables directly to the ignition switch, as it will not be able to handle
the current required to operate the ECU.
Please refer to the wiring diagrams contained within this quick start guide for a recommended
power relay setup on an unwired vehicle.
To avoid damage to ignition components, never connect the ignition modules to
the ECU until the ECU is configured. The same applies to the fuel system, never
connect fuel injectors until the ECU is configured, otherwise the engine may
flood with fuel.
Grounding
One of the most common wiring problems experienced is poor grounding. There should be
no paint, anodizing or other surface layer protection between the ground wire and engine
block or chassis. Temporary wiring will almost certainly cause a problem, use a proper ground
eyelet terminal and do not use loctite or similar locking agents as they may become insulators
preventing good earth connection.
ECU Ground (Black) should be connected to the chassis of the vehicle, and
Signal Ground (Black / White) should be connected directly to the Battery negative terminal.
Please make sure your Engine block has a ground strap to the chassis.
Figure 11 – Main Power Wiring
3.Now you will be able to access all the information contained on the CD
Page 11
ECU Manager Software
ECU Manager software is used for setup, calibration and diagnostics and can
be found on the CD supplied with this unit or downloaded from the Haltech website
www.haltech.com
Minimum System Requirements
Operating System: Windows 2000 SP4 / XP / Vista / Windows 7
Processor Speed: 1GHz
RAM: 256 Mb
Video Card: 128MB graphics card with 3D acceleration
USB: 1.1
Hard Drive Space: 250Mb
Minimum Screen Resolution: 1024 x 768 pixels
Installing ECU Manager
Installing ECU Manager onto your PC is performed similar to any other Windows
software package. Installation is outlined below to ensure correct installation:
1.Insert the CD-ROM into your PC’s CD-ROM drive. The CD should automatically
launch into the Haltech Browser. If the CD does not run automatically double
click on the “My Computer” icon on the desktop, double click on the Haltech icon
(CD- ROM drive) to start the browser software.
2.The Browser will display the disclaimer and you will need to agree to the
terms stated before allowing to progress. Read the Disclaimer and click on
AGREE if you agree.
3.Now you will be able to access all the information contained on the CD
4.To download the Platinum Software, click on the Platinum Series ECU Manager
Link. You will be prompted to install the software. Click “Install” to install
ECU Manager and the Data Log viewer.
5. Follow the software prompts and install the software.
With your programming cable (USB) attached to your ECU and the other end
connected to your laptop, power up the ECU by turning your key to IGN. Start the
programming software on your PC and go online with the ECU.
Page 12
Initial Software Setup
Main Setup (Basic) Page
Set the basic engine parameters in the main setup page, number of cylinders,
firing order, load source and map source (enable or disable the use of the internal map sensor)
Trigger Setup Page
Set the crank and cam (trigger and home) angle sensor type and description in the
Trigger setup page. If using a hall effect or optical style crank sensor then set trigger
type to hall effect.
In most stand alone applications the trigger pullup will need to be set to ON when
using a hall effect crank sensor. In a piggy back application the pullup will be set to
off. Trigger pullup will be set to off for all reluctor (sine wave) style trigger inputs.
Ignition Setup Page
Setting the base timing needs to be done with the ignition setup page open. Base
timing is the process of synchronising the ECU’s operations with the engines.
This needs to be calibrated so that the ECU knows the crankshaft position at any point in
time. This is required for accurate fuel delivery and spark timing.
First, go to the fuel setup page and disable the fuel injectors (at this stage it is not
desired that the engine attempts to start). To reduce stress on the starter motor it is also
advisable to remove the spark plugs to help the engine crank more freely when
setting base timing.
Set lock timing to ON and lock timing angle to 10 degrees. Crank engine, using a
timing light connected to ignition lead for number 1 cylinder. Adjust the tooth offset
and trigger angle until timing reads 10 degrees as viewed with a timing light on
crank pulley. Tooth offset gives large changes to timing, trigger angle is used to fine
tune timing to exactly 10 degrees (any angle can be set as the lock timing angle; in
this example 10 degrees was used). It is however possible to set the lock timing to
zero degrees (or any other positive number) and adjust tooth offset and trigger
angle until the crank pulley shows this value when viewed with a timing light.
If there is no RPM being displayed in the software check for correct trigger setup, correct
sensor wiring, correct trigger type, pull ups enabled / disabled, trigger edge falling / rising.
Fuel Setup Page
Set the basic fuel parameters, injection mode, fuel pump prime time and ensure that the fuel
injectors are enabled in this setup page once ignition timing has been checked.
When using crimp connectors ensure that the correct crimping tool is used – if in
Page 13
Startup
With the settings now calibrated with correct fuel setup, ignition setup and trigger
setup, go to the Main setup menu and calibrate the throttle
Check to ensure that the fuel and ignition maps all have sensible values in them.
Check that all sensors are reading correctly by going to the engine data page and
viewing their values. Ensure the throttle reads smoothly from 0-100% in its full
range of movement. The MAP sensor should read atmospheric pressure
when the engine is stopped.
Power up the fuel pumps and check entire fuel system for leaks before attempting
to start the engine.
Once verified that all sensors are correctly operating and fuel system is functional,
attempt to start the engine. If engine does not start check:
1. Ignition Timing
2. Correct Fuel Pressure
3. Spark Plugs are not fouled or wet
4. Engine Compression
5. Ignition is wired in correct firing order
6. Ignition is firing on intake stroke not exhaust stroke
Once engine is running, ensure fuel pressure remains correct under all conditions and
that battery is charging.
Page 14
ECU Manager / ECU Manuals
85 87 87
86 30
TO 12V IGNITION SUPPLY
TO - TRIGGER FROM ECU
TO FUEL PUMP + TERMINAL
TO 12V SUPPLY
FUEL PUMP
+
_
TO GROUND
VIA FUEL PUMP FUSE
FUSE
POSITIVE SWITCHED
FUEL PUMP CONTROL
12V FUEL PUMP RELAY
Detailed manuals can be found in the software by pressing your F1 key or by
selecting the Help tab located at the top left of the screen.
ECU Manager File Extensions
When ECU manager saves the map from the Haltech ECU, it saves the map with
a Haltech specific file extension.
The File extension can be broken down as follows:
Example File : xxxx.hspr05 -106
Later map versions cannot be loaded into ECU's with earlier firmware versions.
ECU Manager will upgrade earlier map versions when loading into ECU's with later
firmware versions.
ECU Manager upgrades maps between versions where equivalent settings are
available. However, new settings not in the original map, will be substituted with
values from the new version's default map.
Whenever ECU Manager converts your ECU map, you should always check your
map settings to ensure that all the appropriate settings have been converted
correctly.
greater than 8 Ohms, if injectors are used that are less than 8 Ohms, excessive current
Page 15
CAN Devices
1234
5678
Device
1
Terminating
Resistor
Required
Device
2
Terminating
Resistor
Not Required
Device
3
Terminating
Resistor
Not Required
Device
4
Terminating
Resistor
Required
CAN BUS
Pin # Function
1 Ground
2 120 Ohm Terminating Resistor Loop
3 CAN LO
4 12V Out
5 Reserved
6 120 Ohm Terminating Resistor Loop
7 CAN HI
8 Reserved
The Platinum Sprint 500 ECU can interface directly with selected CAN devices.
CAN connections can be found on the 8 pin rear connector.
A 120 OHM terminating resistor connected between CAN High and CAN Low
terminations may be needed in some applications where the ECU is located at the end
of the CAN Bus.
The ECU is equipped with an internal terminating resistor which can be enabled by
fitting a wire link between pins 2 and 6 of the 8 pin connector.
( Please see example below , connector sold separately Haltech Part # HT030003 )
Wiring Information for our range of data acquisition dashes can be found on our website
www.haltech.com
Figure 12 – Terminating Resistor Example
Figure 13 – Rear CAN Connector (Sold Separately)
Page 16
ECU Connection Table
Pin # Wire Colour Connection
1 Y (4 CORE GY) TRIGGER ( + )
2 Y (4 CORE GY/B) HOME ( + )
3 -
4 GY <SHD> ROADSPEED INPUT (DPI1)
5 -
6 V/B TACHO OUTPUT (DPO1)
7 V/BR THERMOFAN OUTPUT (DPO2)
8 V/R GENERAL PURPOSE OUTPUT 1 (DPO3)
9 V/O GENERAL PURPOSE OUTPUT 2 (DPO4)
10 GY/R +12V SWITCHED
11 R +12V SWITCHED
12 B/Y FUEL PUMP RELAY TRIGGER
13 L/R INJECTOR # 4
14 L/BR INJECTOR # 3
15 L/B INJECTOR # 2
16 L INJECTOR # 1
17 G (4 CORE GY) TRIGGER ( - )
18 G (4 CORE GY/B) HOME ( - )
19 -
20 O/B AUX REV LIMITER (AVI1)
21 GY/O <SHD> O2 SENSOR INPUT
22 B/W SIGNAL GROUND
23 B POWER GROUND
24 V COOLANT TEMPERATURE (ATI1)
25 GY AIR TEMPERATURE (ATI2)
26 Y MAP
27 W TPS
28 O +5V
29 Y/G IGNITION OUTPUT # 4
30 Y/O IGNITION OUTPUT # 3
31 Y/R IGNITION OUTPUT # 2
32 Y/B IGNITION OUTPUT # 1
Figure 14 – Platinum Sprint 500 Connections table
Page 17
Optional Haltech Ballast Resistor Wiring
Notes
Page 18
Appendix
PLATINUM SPRINT 500
RECOMMENDED POWER RELAY CONFIGURATION
[B] AVSS 0.50
[R] AVSS 0.50
[R/L] AVSS 1.25
TO ECU PIN 11
TO INJECTORS
SWITCHED +12V SUPPLY
FROM IGNITION SWITCH
30
87
87
85
86
ECU POWER RELAY
30
87
87
85
86
FUEL PUMP RELAY
30
87
87
85
86
IGNITION POWER RELAY
[B/Y] AVSS 0.50
[B] AVSS 0.50
[R/W] AVSS 0.50
[P] AVSS 0.50
[P] AVSS 0.50
[P] AVSS 0.50
20A
15A
10A
20A
[R] AVSS 1.25
[R] AVSS 1.25
TO BATTERY
POSITIVE +
30
87
87
85
86
INJECTION POWER RELAY
[P] AVSS 0.50
TO ECU PIN 10
[B] AVSS 0.50
[R/Y] AVSS 1.25
TO IGNITION COILS
TO ECU PIN 12
[O/L] AVSS 1.25
TO POSITIVE SIDE OF FUEL PUMP
[R]AVSS 1.25
[O/GY]AVSS 1.25
[R/Y]AVSS 1.25
[R/W] AVSS 0.50
TO ECU PIN 23
TO CHASSIS GROUND
[B] AVSS 2.00
FUSE BLOCK CONNECTOR
PACKARD: 1200 4943
[B] AVSS 0.50
NOTES
BOSCH RELAY P/N: 332 019 150
OR EQUIVALENT MUST BE USED
WIRING NOTES:
1. MAIN WIRE COLOUR LISTED FIRST
E.G. RED/GRN INDICATES RED WIRE WITH GREEN STRIPE
2. USE V-90 HT PVC INSULATION.
3. WIRE SIZES ARE SHOWN IN AVSS (sq.mm)
[R] AVSS 1.25
[R/W] AVSS 1.25
HALTECH, SYDNEY AUSTRALIA
DATE: 5TH NOVEMBER 2010
SHEET 2 OF 2REV F
PLATINUM SPRINT 500 WIRING
Page 19
Page 20
HALTECH HEAD OFFICE: PH: +612 9729 0999
FAX: +612 9729 0900
EMAIL: sales@haltech.com
HALTECH US OFFICE: EMAIL: usa@haltech.com
See the Haltech Website for your local authorized dealer.
www.haltech.com
Version 6
QUICK START GUIDE
Loading...