Halsey Taylor WM14A-CB-Q User Manual

These water coolers are certified to

NSF/ANSI 61.

GENERAL

Self-contained, electric refrigerated, wall­mounted water cooler designed to be easily
accessible to able-bodied individuals. Unit
meets requirements of the Safe Drinking
Water Act. Unit provides 50° F water at
80° F inlet water and 90° F ambient.

CABINET

Heavy-gauge vinyl clad steel. Resistant to
wear, moisture, perspiration, heat and sunlight.
Optional Stainless Steel is available.

COOLER TOP

Non-corrosive stainless steel cooler top, number
300 series with satin finish resists stains and
corrosion and is easy to maintain. Anti-splash
ridge reduces splatter. Contoured to insure
proper drainage.

BUBBLER

Exclusive one-piece, chrome-plated two-stream
mound-building bubbler with non-removable
anti-squirt feature and integral hood insures a
satisfying drink of water.

PUSHBUTTON ACTUATION MECHANISM

Self closing, vandal-resistant pushbutton does
not require grasping or twisting.

AUTOMATIC STREAM HEIGHT REGULATOR

Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatically
maintained under line pressures that vary from
20 to 105 psi.

INLET STRAINER

Easily cleaned in-line strainer screen traps
particles of 140 microns or larger before they
enter the waterway.

TEMPERATURE CONTROL

Positive sensing thermostat for controlling
temperature of storage tank water. Factory set
at 50° F Adjustable ±5° F.

STORAGE TANK

Non-pressurized stainless steel
evaporator/storage tank for long life.
Waterways are certified to NSF/ANSI 61
far exceeding the requirements of the
Safe Drinking Water Act.

HOT WATER HEATER/CUP FILLER

Factory-installed “Coffee-Bar Server” consists
of electrically heated hot water tank (capacity
4 pints) and a gooseneck, lever-operated cup
filler. Serves 40 six-ounce cups of 165° water
per hour.

REFRIGERATION SYSTEM

Hermetically sealed, positive start compressor
with lifetime lubrication and built-in overload
protection, efficient capillary sizing, large
capacity dryer-strainer, and fan cooled
copper/aluminum condenser with self-lubricated
bearing. System uses R134A refrigerant.
Protected by Halsey Taylor’s Limited 5 Year
Warranty.

VENTILATION

Insure proper ventilation by maintaining
6" (152mm) minimum clearance from
cabinet louvers to wall.

SUGGESTED SPECIFICATIONS

Shall deliver ( ) GPH of 50° F water at
90° F ambient and 80° F inlet water. Shall have
stainless steel basin with removable drain
strainer. Bubbler shall be two stream, mound­building type. Separate valve and automatic
stream regulator shall be mounted within
cabinet. Refrigeration system shall employ high
efficiency, positive start compressor using
R134A non-pressurized tank with totally
encapsulated insulation and be controlled by
positive sensing thermostat. The manufacturer
shall certify the unit to meet the requirements of
NSF/ANSI 61, and the Safe Drinking Water Act.
Unit complies with ARI Standard 1010.

NOTE: Continued product improvement makes
specifications subject to change without notice.
See Halsey Taylor website for most current
spec sheet.

Standard Finish is Platinum Vinyl

Optional Finishes (no extra cost)

■■

Slate

■■

Almond

Optional Finishes (extra cost)

■■

All Stainless Steel

Optional Accessories (extra cost)

■■

Vandal-Resistant Kit

■■

Water Filter

■■

Easy-Flex™Bubbler

Trap and service stop not included.

HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523

C3 / 1-2005

MODELS: ■■WM8A-CB-Q ■■WM14A-CB-Q

With Coffee Bar

Wall-Mounted Cooler

www.halseytaylor.com

WM SERIES

Model GPH Capacity Base F.L. Shipping Rated
No. Cooled to 50° F* Rate Amps Weight Watt

Ambient Air Temp

Cap. lb. Usage

70°F 80°F 90°F

†

100°F

WM8A-CB-Q 9.7 8.8 8.0 7.2 8.0 10.3 69 1185
WM14A-CB-Q 16.3 14.9 13.5 12.2 13.5 14.3 75 1645

* With projector service and tap water at 80° F

†

UL listed and complies with ARI Standard 1010

Printed in the U.S.A.

Wall-Mounted Cooler
With Coffee Bar

(CONTINUED)

MOUNTING HEIGHT

Adult mounting height recommended 40" from
basin to floor. May be mounted at any desired
height.

MOUNTING INSTRUCTIONS

Mount trap and install service stop to building
supply line. Anchor hanger bracket securely to
wall on all sides. To insure proper engaging of
waste line into trap, centerline of trap must be
6

1

/4" from wall face.

Remove slip nut and gasket from trap and
install on waste line tube. Hang cooler on
bracket and engage waste line tube into trap
inlet. Centerline height of waste outlet is 22

1

/2"

from floor line for conventional adult installation.

PLUMBING CONNECTIONS

Enter directly into cabinet. Waste 1

1

/4" O.D. slip

connection. Supply

3

/8" tubing.

Trap and service stop not included.

OPERATING PRESSURES:

Supply water-105 psi maximum

ELECTRICAL DATA

Furnished with plug-in, 3-wire grounding type
service cord. Standard 120 volt, 60 Hz, single
phase. Install 120 volt receptacle, rated at
15-amp minimum, to receive 3-wire parallel
blade grounding type male plug.

SIDE VIEWFRONT VIEW / WALL LAYOUT

NOTE: Optional holes may be added to back panel to secure bottom of cooler to wall.
Minimum wall clearance for air flow is 4 inches (102mm) on either side.

NOTE: A service supply stop must be installed at the cooler inlet line.