Halsey Taylor SJ30-Q User Manual

Certified to NSF/ANSI 61.

CABINET

Manufactured of rust-resistant heavy gauge
galvanized steel. Removable service panels.

PLUMBING CONNECTIONS

3

⁄8" O.D. stainless steel tubing inlet and outlet.

ELECTRICAL CONNECTION

7

⁄8" diameter opening for conduit connection.

COOLING UNIT

Combination tube-tank type. Tube portion is
continuous coil of copper tubing. Tank is
stainless steel.

TEMPERATURE CONTROL

Positive sensing thermostat for controlling
temperature of evaporator/chiller storage
water. Factory set for 40°F water. Adjustable
to 50°.

FAN MOTOR

Unit bearing self-lubricating type for
maintenance-free longer life.

CONDENSER

Copper/aluminum construction with
aluminum fins.

DRAIN PLUG

Provided with drain plug with O-ring seal.

REFRIGERATION SYSTEM

Hermetically sealed, positive start compressor
with lifetime lubrication and built-in overload
protection, efficient capillary sizing, large
capacity dryer-strainer, and self-lubricated fan
cools copper/aluminum condenser. System
uses R134A refrigerant. Test pressures,
highside 375 psig., lowside 150 psig.
Protected by Halsey Taylor’s Limited 5 Year
Warranty.

VENTILATION

It is important to insure proper ventilation.
A minimum of 6 inches (152mm) to the front
must be maintained, and 6 inches (152mm) to
the rear of the unit.

NOTE: Continued product improvement makes
specifications subject to change without
notice.See Halsey Taylor website for most
current spec sheet.

ELECTRICAL

Furnished with 6" leads enclosed in junction
box for direct connection to standard 115 volt,
60 Hz, single phase.

SUGGESTED SPECIFICATIONS

Shall deliver 29.5 GPH of 50°F water at 90°F
ambient and 80°F inlet water. Designed for
use where large quantity of chilled water is
required. Compressor shall be hermetically
sealed. Manufacturer shall certify unit to be
lead free as defined by the Safe Drinking
Water Act. System controlled by adjustable
thermostat. Complies with ARI Standard 1010.

SJ30 can serve 3 fountains

Locate chiller within 15 feet of fountain for
optimum performance.

HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523

E5 / 8-2007

MODEL SJ30-Q

LARGE REMOTE CHILLER

Model GPH Capacity Base F.L. Shipping Rated
No. Cooled to 50° F* Rate Amps Weight Watt

Ambient Air Temp

Cap. lb. Usage

70°F 80°F 90°F†100°F

SJ30-Q 33.9 31.9 29.5 27.1 29.5 14.0 118 1290

* With projector service at 1ft. from outlet and supply water at 80° F

†

UL listed and complies with ARI Standard 1010

NOTE: A service supply stop (not included) should be installed at the cooler inlet line.

Remote Chiller

Large

halseytaylor.com

JOB NAME:

ENGINEER/CONTRACTOR NAME:

APPROVAL:

DATE:

Printed in the U.S.A.

SJ30-Q

Large Remote
Chiller

(CONTINUED)

INSTALLATION

A minimum clearance of 6" in front and back of
unit is required to insure proper ventilation.

OPERATING PRESSURES:

Supply water - 105 psi maximum

Dimensions

331⁄4"W x 133⁄4"D x 16"H

Shipping weight: 125 lbs.

LEFT SIDE VIEW FRONT VIEW

LEGEND:

A = 3/8" O.D. TUBE WATER INLET
B = 3/8" O.D. TUBE WATER OUTLET
C = TEMPERATURE ADJUSTMENT
D = ELECTRICAL
E = 3/8" O.D. TUBE TANK DRAIN

NOTE: A service supply stop (not included) should be installed at the water inlet line.