Halsey Taylor SCWT-L-R User Manual
These water coolers are certified to
NSF/ANSI 61.
GENERAL
Self-contained, electric refrigerated,
free-standing water cooler designed to be
easily accessible to able-bodied individuals.
Unit is certified to NSF/ANSI 61 and meets
requirements of the Safe Drinking Water Act.
Unit provides 50° F water at 80° F inlet water
and 90° F ambient.
CABINET
Heavy-gauge vinyl clad steel. Resistant to
wear, moisture, perspiration, heat, and sunlight. Optional Stainless Steel is available.
COOLER TOP
Non-corrosive stainless steel cooler top, number
300 series with satin finish resists stains and
corrosion and is easy to maintain. Anti-splash
ridge reduces splatter. Contoured to insure
proper drainage.
BUBBLER
Exclusive one-piece, chrome-plated two-stream
mound-building bubbler with non-removable
anti-squirt feature and integral hood insures a
satisfying drink of water.
PUSHBUTTON ACTUATION MECHANISM
Self-closing, vandal-resistant pushbutton does
not require grasping or twisting.
AUTOMATIC STREAM HEIGHT REGULATOR
Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatically
maintained under line pressures that vary from
20 to 105 psi.
INLET STRAINER
Easily cleaned in-line strainer screen traps
particles of 140 microns or larger before they
enter the waterway.
TEMPERATURE CONTROL
Positive sensing thermostat for controlling
temperature of storage tank water. Factory set
at 50° F Adjustable ±5° F.
STORAGE TANK
Non-pressurized stainless steel
evaporator/storage tank for long life.
Waterways are certified to NSF/ANSI 61,
far exceeding the requirements of the
Safe Drinking Water Act.
REFRIGERATION SYSTEM
Hermetically sealed, positive start compressor
with lifetime lubrication and built-in overload
protection, efficient capillary sizing, large
capacity dryer-strainer, and self-lubricated fan
cools copper/aluminum condenser. System
uses R134A refrigerant. Protected by Halsey
Taylor’s Limited 5 Year Warranty.
VENTILATION
Insure proper ventilation by maintaining
6" (152mm) clearance from cabinet louvers
to wall.
SUGGESTED SPECIFICATIONS
Shall deliver ( ) GPH of 50° F water at 90° F
ambient and 80° F inlet water. Shall have
stainless steel basin with removable drain
strainer. Bubbler shall be two-stream, moundbuilding type. Separate valve and automatic
stream regulator shall be mounted within
cabinet. Refrigeration system shall employ high
efficiency, positive start compressor using
R134A, non-pressurized tank with totally
encapsulated insulation and be controlled by
positive sensing thermostat. The manufacturer
shall certify the unit to meet the requirements
of NSF/ANSI 61, and the Safe Drinking Water
Act. Unit complies with ARI Standard 1010.
NOTE: Continued product improvement makes
specifications subject to change without
notice. See Halsey Taylor website for most
current spec sheet.
Standard finish is Platinum Vinyl
Optional Finishes (no extra cost)
■■
Slate
■■
Almond
Optional Finishes (extra cost)
■■
All Stainless Steel
Optional Accessories (extra cost)
■■
Glass Filler Kit
■■
Sump Pump Kit
■■
Back Panel 27082C
■■
Water Filter
■■
Vandal-Resistant Kit
■■
Foot Pedal Kit
■■
Easy Flex™Bubbler
■■
Coffee Server (factory installed for
SCWT8A-Q & SCWT14A-Q only)
Trap and service stop not included.
HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
C11 / 8-2007
MODEL: ■■SCWT4A-Q
■■
SCWT8A-Q
■■
SCWT14A-Q
■■
SCWT-L/R (Less Refrigeration)
SCWT SERIES
Model GPH Capacity Base F.L. Shipping Rated
No. Cooled to 50° F* Rate Amps Weight Watt
Ambient Air Temp
Cap. lb. Usage
70°F 80°F 90°F
†
100°F
SCWT4A-Q 4.8 4.4 4.0 3.6 4.0 2.5 72 230
SCWT8A-Q 9.2 8.4 7.6 6.8 7.6 4.0 73 370
SCWT14A-Q 16.3 14.9 13.5 12.2 13.5 7.2 76 690
* With projector service and tap water at 80° F.
†
UL listed and complies with ARI Standard 1010
Free-Standing Cooler
Deluxe
halseytaylor.com
JOB NAME:
ENGINEER/CONTRACTOR NAME:
APPROVAL:
DATE:
Printed in the U.S.A.
SCWT4A-Q, SCWT8A-Q,
SCWT14A-Q, SCWT-L/R
Deluxe Free-Standing
Cooler
(CONTINUED)
ROUGH-IN, MOUNTING, AND
ELECTRICAL INSTRUCTIONS
This cooler may be installed against the wall or
freestanding from the wall.
NOTE: With slight modifications, rough-in
heights from 16.5" and 24.3" can be
accommodated. 2" maximum may be cut from
the tailpiece provided.
For against-the-wall installation
Provide 2" x 4" wood blocking back of finished
wall for securing cooler flush with finished wall.
(Refer to rough-in drawing.) Install 1
1
/4" trap 51/4"
from wall face to center of trap inlet. Trap not
furnished. Install
3
/8" IPS service stop to building
supply line. Service stop not furnished.
Trap and service stop not included.
OPERATING PRESSURES
Supply water-105 psi maximum
ELECTRICAL
Electrical receptacle to be installed to receive
3-wire parallel blade grounding type male plug.
Note cord length is 4 feet from cord exit point in
cooler. Cooler can now be mounted against the
wall and secured to blocking with two wood
screws. Be sure 1
1
/4" O.D. slip connection tube
from cooler waste to trap is in line. Connect
water supply line to
3
/8" tubing inlet connection
located inside of cabinet below shelf.
For freestanding installation
A hole is provided in back of cabinet for
plumbing entrance. See rough-in drawing and
outline drawing. Install 1
1
/4" IPS trap inside
cabinet. Trap not furnished. Install
3
/8" IPS
service stop to building supply line outside of
cooler cabinet. Service stop not furnished.
Connect water supply from building to
3
/8"
tubing inlet connection located inside of cabinet
below shelf.
NOTE: Installation outdoors in an unprotected
environment is not recommended.
SIDE VIEW
FRONT VIEW
NOTE: Minimum wall clearance for air flow is 4 inches (102mm) on either side.
NOTE: A service supply stop must be installed at the cooler inlet line.
Loading...