Halsey Taylor SCWT8A-WF-Q User Manual

This water cooler is certified to

NSF/ANSI 61.

GENERAL

Self-contained, electric refrigerated,
free-standing water cooler with filter designed
to be easily accessible to able-bodied individuals.
Unit is certified to NSF/ANSI 61 and meets
requirements of the Safe Drinking Water Act.
Unit provides 50° F water at 80° F inlet water
and 90° F ambient.

LEAD REDUCTION FILTER

Halsey Taylor Water Cooler With Filter is
equipped with the Water Sentry HWF 172 lead
reduction system which is designed to remove
cysts, such as cryptrosporidium and giardia,
lead particles and chlorine. Also reduces odors
and discoloration from incoming water. The
filter has been tested to the following NSF
International standards: NSF/ANSI Standards
42 Chlorine, Particulate, and Taste and Odor.
NSF/ANSI Standard 53 for Reduction of Lead
and Cyst. Features include Quick-Disconnect
1/4 turn installation. Has automatic inlet shut­off valve that closes when filter is removed.
Filter should be replaced every 1,500 gallons
(5678 liters) or approximately one (1) year after
installation. Use part number 55897C when
ordering replacement filter.

CABINET

Heavy-gauge vinyl clad steel. Resistant to
wear, moisture, perspiration, heat, and sunlight.
Optional Stainless Steel is available.

COOLER TOP

Non-corrosive stainless steel cooler top, number
300 series with satin finish resists stains and
corrosion and is easy to maintain. Anti-splash
ridge reduces splatter. Contoured to insure
proper drainage.

BUBBLER

Exclusive one-piece, chrome-plated two-stream
mound-building bubbler with non-removable
anti-squirt feature and integral hood insures a
satisfying drink of water.

PUSHBUTTON ACTUATION MECHANISM

Self-closing, vandal-resistant pushbutton does
not require grasping or twisting.

AUTOMATIC STREAM HEIGHT REGULATOR

Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatically
maintained under line pressures that vary from
20 to 105 psi.

INLET STRAINER

Easily cleaned in-line strainer screen traps
particles of 140 microns or larger before they
enter the waterway.

TEMPERATURE CONTROL

Positive sensing thermostat for controlling
temperature of storage tank water. Factory set
at 50° F Adjustable ±5° F.

STORAGE TANK

Non-pressurized stainless steel evaporator/
storage tank for long life. Waterways are
certified to NSF/ANSI 61, far exceeding the
requirements of the Safe Drinking Water Act.

REFRIGERATION SYSTEM

Hermetically sealed, positive start compressor
with lifetime lubrication and built-in overload
protection, efficient capillary sizing, large
capacity dryer-strainer, and self-lubricated fan
cools copper/aluminum condenser. System
uses R134A refrigerant. Protected by Halsey
Taylor’s Limited 5 Year Warranty.

VENTILATION

Insure proper ventilation by maintaining
6" (152mm) minimum clearance from
cabinet louvers to wall.

SUGGESTED SPECIFICATIONS

Shall deliver 8.0 GPH of 50° F water at 90° F
ambient and 80° F inlet water. Shall have lead
reduction filter and stainless steel basin with
removable drain strainer. Bubbler shall be two­stream, mound- building type. Separate valve
and automatic stream regulator shall be mounted
within cabinet. Refrigeration system shall
employ high efficiency, positive start compressor
using R134A, non-pressurized tank with totally
encapsulated insulation and be controlled by
positive sensing thermostat. The manufacturer
shall certify the unit to meet the requirements
of NSF/ANSI 61, and the Safe Drinking Water
Act. Unit complies with ARI Standard 1010.

NOTE: Continued product improvement makes
specifications subject to change without
notice. See Halsey Taylor website for most
current spec sheet.

Standard finish is Platinum Vinyl

Optional Finish (extra cost)

■■

All Stainless Steel

Optional Accessories (extra cost)

■■

Glass Filler Kit

■■

Sump Pump Kit

■■

Back Panel 27082C

■■

Vandal-Resistant Kit

■■

Foot Pedal Kit

■■

Easy Flex™Bubbler

■■

Coffee Server (factory installed only)

Trap and service stop not included.

HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523

C12 / 8-2007

MODEL SCWT8A-WF-Q

SCWT SERIES

Model GPH Capacity Base F.L. Shipping Rated
No. Cooled to 50° F* Rate Amps Weight Watt

Ambient Air Temp

Cap. lb. Usage

70°F 80°F 90°F

†

100°F

SCWT8A-WF-Q 9.2 8.4 7.6 6.8 7.6 4.0 76 370

* With projector service and tap water at 80° F.

†

UL listed and complies with ARI Standard 1010

Deluxe Free-Standing

Cooler With Filter

halseytaylor.com

JOB NAME:

ENGINEER/CONTRACTOR NAME:

APPROVAL:

DATE:

Printed in the U.S.A.

SCWT8A-WF-Q

Deluxe Free-Standing
Cooler With Filter

(CONTINUED)

ROUGH-IN, MOUNTING, AND
ELECTRICAL INSTRUCTIONS

This cooler may be installed against the wall or
freestanding from the wall.
NOTE: With slight modifications, rough-in
heights from 16.5" and 24.3" can be
accommodated. 2" maximum may be cut from
the tailpiece provided.

For against-the-wall installation

Provide 2" x 4" wood blocking back of finished
wall for securing cooler flush with finished wall.
(Refer to rough-in drawing.) Install 1

1

/4" trap 51/4"

from wall face to center of trap inlet. Trap not
furnished. Install

3

/8" IPS service stop to building

supply line.

Trap and service stop not included.

OPERATING PRESSURES:

Supply water-105 psi maximum

ELECTRICAL

Electrical receptacle to be installed to receive
3-wire parallel blade grounding type male plug.
Note cord length is 4 feet from cord exit point in
cooler. Cooler can now be mounted against the
wall and secured to blocking with two wood
screws. Be sure 1

1

/4" O.D. slip connection tube

from cooler waste to trap is in line. Connect
water supply line to

3

/8" tubing inlet connection

located inside of cabinet below shelf.

For freestanding installation

A hole is provided in back of cabinet for
plumbing entrance. See rough-in drawing and
outline drawing. Install 1

1

/4" IPS trap inside

cabinet. Trap not furnished. Install

3

/8" IPS

service stop to building supply line outside of
cooler cabinet. Service stop not furnished.
Connect water supply from building to

3

/8"

tubing inlet connection located inside of cabinet
below shelf.

NOTE: Installation outdoors in an unprotected

environment is not recommended.

SIDE VIEW

FRONT VIEW

NOTE: Minimum wall clearance for air flow is 4" (102mm) on either side.
NOTE: A service supply stop must be installed at the cooler inlet line.