Halsey Taylor SCWT14FL-Q User Manual
This water cooler is certified to
NSF/ANSI 61.
GENERAL
Self-contained, electric refrigerated,
free-standing water cooler designed to be
easily accessible to able-bodied individuals.
Unit is certified to NSF/ANSI 61 and meets
requirements of the Safe Drinking Water Act.
Unit provides 50° F water at 80° F inlet water
and 90° F ambient.
CABINET
Heavy-gauge vinyl clad steel. Resistant to
wear, moisture, perspiration, heat, and sunlight.
Optional Stainless Steel is available.
COOLER TOP
Non-corrosive stainless steel cooler top, number
300 series with satin finish resists stains and
corrosion and is easy to maintain. Anti-splash
ridge reduces splatter. Contoured to insure
proper drainage.
BUBBLER
Exclusive one-piece, chrome-plated two-stream
mound-building bubbler with non-removable
anti-squirt feature and integral hood insures a
satisfying drink of water.
SIDE-MOUNTED FOUNTAIN
Stainless steel basin. Fountain has separate
valve and automatic stream regulator. Waste
outlet and water supply are integral with electric
water cooler.
PUSHBUTTON ACTUATION MECHANISM
Self-closing, vandal-resistant pushbutton does
not require grasping or twisting.
AUTOMATIC STREAM HEIGHT REGULATOR
Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatically
maintained under line pressures that vary from
20 to 105 psi.
INLET STRAINER
Easily cleaned in-line strainer screen traps
particles of 140 microns or larger before they
enter the waterway.
TEMPERATURE CONTROL
Positive sensing thermostat for controlling
temperature of storage tank water. Factory set
at 50° F Adjustable ±5° F.
STORAGE TANK
Stainless steel evaporator/storage tank for long
life. Waterways are certified to NSF/ANSI 61,
far exceeding the requirements of the
Safe Drinking Water Act.
REFRIGERATION SYSTEM
Hermetically sealed, positive start compressor
with lifetime lubrication and built-in overload
protection, efficient capillary sizing, large
capacity dryer-strainer, and fan cooled
copper/aluminum condenser with self-lubricated
bearing. System uses R134A refrigerant.
Protected by Halsey Taylor’s Limited 5 Year
Warranty.
VENTILATION
Insure proper ventilation by maintaining
6" (152mm) minimum clearance from
cabinet louvers to wall.
SUGGESTED SPECIFICATIONS
Shall deliver 14.0 GPH of 50° F water at
90° F ambient and 80° F inlet water. Shall have
stainless steel basin with removable drain
strainer. Bubbler shall be two-stream, moundbuilding type. Separate valve and automatic
stream regulator shall be mounted within
cabinet. Refrigeration system shall employ high
efficiency, positive start compressor using
R134A, evaporator/tank with totally encapsulated
insulation and be controlled by positive sensing
thermostat. Side fountain to be satin finish
stainless steel with pushbutton actuation.
The manufacturer shall certify the unit to meet
the requirements of NSF/ANSI 61, and the
Safe Drinking Water Act. Unit complies with
ARI Standard 1010.
NOTE: Continued product improvement makes
specifications subject to change without notice.
See Halsey Taylor website for most current
spec sheet.
Standard finish is Platinum Vinyl
Optional Finishes (no extra cost)
■■
Slate
■■
Almond
Optional Finishes (extra cost)
■■
All Stainless Steel
Optional Accessories (extra cost)
■■
Glass Filler Kit
■■
Sump Pump Kit
■■
Vandal-Resistant Kits
■■
Water Filter
■■
Foot Pedal Kit
■■
Easy-Flex™Bubblers
■■
Back Panel (27082C)
Trap and service stop not included.
HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
C18 / 1-2005
MODEL: ■■SCWT14FL-Q
SCWT SERIES
Model GPH Capacity Base F.L. Shipping Rated
No. Cooled to 50° F* Rate Amps Weight Watt
Ambient Air Temp
Cap. lb. Usage
70°F 80°F 90°F
†
100°F
SCWT14FL-Q 18.0 15.8 13.5 12.6 13.5 8.0 80 625
* With projector service and tap water at 80° F
†
UL listed and complies with ARI Standard 1010
With Left Fountain
Free-Standing Cooler
www.halseytaylor.com
Printed in the U.S.A.
Free-Standing Cooler
With Left Fountain
(CONTINUED)
INSTALLATION
This cooler may be installed against the wall or
freestanding from the wall.
For against-the-wall installation
Provide 2" x 4" wood blocking back of finished
wall for securing cooler flush with finished wall.
(Refer to rough-in drawing.) Install 1
1
/4" trap 51/4"
from wall face to center of trap inlet. Trap not
furnished. Install
3
/8" IPS service stop to building
supply line. Union connection and service stop
not furnished.
Trap and service stop not included.
OPERATING PRESSURES
Supply water-105 psi maximum
ELECTRICAL
Electrical receptacle to be installed to receive
3-wire parallel blade grounding type male plug.
Cooler can now be mounted against the wall
and secured to blocking with two wood screws.
Be sure 1
1
/4" O.D. slip connection tube from
cooler waste to trap is in line. Connect water
supply line to
3
/8" tubing inlet connection located
inside of cabinet below shelf.
For freestanding installation
A hole is provided in back of cabinet for
plumbing entrance. Install 1
1
/4" IPS trap inside
cabinet. Trap not furnished. Install
3
/8" IPS
service stop to building supply line outside of
cooler cabinet. Service stop not furnished.
Connect water supply from building to
3
/8" tubing
inlet connection located inside of cabinet below shelf.
NOTE: Installation outdoors in an unprotected
environment is not recommended.
Instructions to mount side fountain at jobsite:
Install fountain hanger to side of cooler cabinet.
Install fountain drain line into side of cooler,
holding fountain in place as guide for proper
alignment.
Remove flare inlet supply fitting from fountain
supply line, and insert into supply opening on
side of cooler.
Place fountain on hanger, insert rubber gasket
between drain elbow and bottom of fountain.
Install drain plug and tighten securely. Connect
fountain supply line to flare sitting on cooler.
Insert fiberglass in housing under fountain and
replace cover plate.
5-1/4"
133mm
SIDE VIEW
FRONT VIEW
NOTE: A service supply stop must be installed at the cooler inlet line.
1-1/4" Trap not included.
Loading...