Halsey Taylor OVL II SREE-Q User Manual

This water cooler is Classified by

Underwriters Laboratories, Inc.
in accordance with ANSI/NSF 61,
Section 9 - 1997b.

GENERAL

Modular, electric refrigerated, wall-mounted
water cooler designed to be easily accessible
to able-bodied individuals. Unit is certified to
ANSI/NSF 61 Sec. 9 and meets requirements
of the Safe Drinking Water Act. Unit provides
50° F water at 80° F inlet water and 90° F
ambient.

FOUNTAIN

Oval basin shape, non-corrosive stainless
steel, with brushed satin finish. Contour-formed
basin with rounded corners and edges.

AUTOMATIC ACTUATION

Model OVL II™SREE-Q features infra-red light
beam emitting sensor and a solenoid valve.
Upon interruption of the light beam, the sensor
actuates the solenoid valve to flow water. User
does not have to touch the water cooler to
obtain a drink of water. Supplied with a built-in
time delay to avoid nuisance actuation from
passers-by.

AUTOMATIC STREAM HEIGHT REGULATOR

Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatical­ly maintained under line pressures that vary
from 20 to 105 psi.

INLET STRAINER

Easily cleaned in-line strainer screen traps
particles of 140 microns o r l a r g e r b e f o r e t h e y
enter the waterway.

REFRIGERATION SYSTEM

Hermetically sealed, positive start compressor
with lifetime lubrication and built-in overload
protection, efficient capillary sizing, large
capacity dryer-strainer, and fan cooled
copper/aluminum condenser with self-lubricated
bearing. System uses R134A refrigerant.
Protected by Halsey Taylor’s Limited 5 Year
Warranty.

MOUNTING FRAME

Mounting frame is manufactured of corrosion
resistant, galvanized steel. Open construction
designed for ease of installation. Mounting
frame can be shipped in advance for rough-in
installation.

PANELS

Constructed of stainless steel, number 300
series with satin finish. Removable lower panel
provides access to plumbing and refrigeration
system. Panels overlap wall opening 1⁄2˝.

SUGGESTED SPECIFICATIONS

Shall deliver 8.3 GPH of 50° F water at 90° F
ambient and 80° F inlet water. Fountain shall
include infra-red sensor, contour-formed basin
to eliminate splashing and standing water, and
rounded corners and edges. Bubbler shall be
chrome plated, two-stream, mound-building
type. Cooling unit shall have a high efficiency
positive start compressor using R134A with
pressurized counterflow cooling
evaporator/chiller. The manufacturer shall
certify the unit to meet the requirements of
ANSI/NSF 61, Section 9 and the Safe Drinking
Water Act. Shall be certified to meet ARI
Standard 1010.

NOTE: Continued product improvement makes
specifications subject to change without notice.

Standard finish is Stainless Steel
Optional Finishes (extra cost)

■■

Aztec Gold

■■

Galaxy Gray Marblyte™(Bowl Only)

■■

Black Onyx Marblyte™(Bowl Only)

Optional Accessories (extra cost)

■■

Vandal-Resistant Kit

■■

Water Filter

■■

Lead Filter

■■

Easy-Flex™Bubbler

Each OVL-II™SREE-Q consists of 3 cartons
as follows:

Mounting Frame
Cooling Unit-SJ8-Q
Fountain, Panels & Misc. Parts

Trap and service stop not furnished.

HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523

C8 / 3-2003

MODEL: ■■OVL II™SREE-Q

Electronic-Eye Cooler

OVL-II™Series

www.halseytaylor.com

OVL II

™

— FACE-MOUNTED SERIES

Model GPH Capacity Base F.L. Shipping Rated
No. Cooled to 50° F* Rate Amps Weight Watt

Ambient Air Temp

Cap. lb. Usage

70°F 80°F 90°F 100°F

OVL II™SREE-Q 9.3 8.3 7.5 6.8 7.5 4.5 97 400

* With projector service and tap water at 80° F

For additional specification of the cooling unit, see specification sheet for Model SJ8 Remote in this catalog.
UL listed and certified to meet ARI Standard 1010

Printed in the U.S.A.

OVL II™Electronic Eye
Cooler

(CONTINUED)

WALL OPENING

IMPORTANT: It is necessary to create a wall
opening 183⁄4"W x 373⁄4"H, and 41⁄2" above the
floor line.

MOUNTING INSTRUCTIONS

Refer to rough-in for location of plumbing and
electrical sources. The support frame is to be
installed first. The shelf for the water chiller
should be assembled to the wall frame, and
then place chiller into position. Hang upper
panel to hanger on frame. Fountain is to be
attached to panel and wall frame. Water service
lines, waste lines and electrical are assembled
as required. The bottom panel is attached last,
after a final check for leaks and correct
functions of fountain and chiller. (For details
see the installation instructions.)

OPERATING PRESSURES:

Supply water - 105 psi maximum

ELECTRICAL DATA

Junction box for a (3) wire 10 AMP branch
circuit. Standard 120 volt, 60 Hz, single phase.

FRONT VIEW

TOP & SIDE VIEWS