Halsey Taylor OVL-II SR-Q, OVL-II ESR-Q, OVL-II SER-Q, OVL-II ER-Q User Manual
OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F
HALSEY TAYLOR OWNERS MANUAL
TM
OVL
Refrigerated Fountains with Back Panel
Figure 1 OVL-II ER-Q Figure 2 OVL-II SR-Q Figure 3 OVLII SER-Q Figure 4 OVL-II ESR-Q
Series Barrier-Free Water Coolers
Figure
1
2
3
4
Model
OVL-II ER-Q
OVL-II SR-Q
OVL-II SER-Q
OVL-II ESR-Q
Description
OVL-II Series - Extended Reach
OVL-II Series - Standard Reach
OVL-II Series - Dual Installation
OVL-II Series - Dual Installation
INSTALLER
!
CAUTION:
!
WARNING:
!
WARNING:
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices to
available water lines. This can, however, cause electrical feedback in the plumbing circuit, which results in an
electrolysis effect occurring in the fountain. This may result in water which has a metallic taste to it or has a
noticeable increase in the metallic content of the water.
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
When inspecting plumbing circuit, remember the line may be grounded some distance from the installation,
and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation. Any drain
fittings provided by the installer should be made of plastic which will
remainder of the buildings plumbing circuits.
1
electronically isolate the fountain from the
97793C - 10/01
1/4" O.D. TUBE
WATER INLET
TO COOLER
NOTE: WATER FLOW
DIRECTION
Figure 5 Water Supply Connections
OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
Installation Package
The components for installation are packed in three
separate boxes, regardless of the type of unit being
installed. The boxes contain the following:
Box No. 1: Wall Frame(s)
Box No. 2: Remote Chiller, SJ8-Q
Box No. 3: Fountain(s), Arm(s) and Panels
Additional materials, as noted in the Parts List, are also
shipped in these boxes.
Parts List
OVL-II OVL-II OVL-II OVL-II Se e
Item Part No. Description ER-Q SR-Q SER-Q ESR-Q Fig.
1
2
3 45396C Bubbler A.G. 1 1 2 2 23
4 100322740560 Bubbler Gasket 1 1 2 2 23
5
6 101570540560 Drain Gasket 1 1 2 2 23
7 51575C Packing Ring 1 1 2 2 23
8 110346220550 Drain Nut 1 1 2 2 23
9 101637451550 Friction Ring 1 1 2 2 23
10
11
12 100023340560 Waste Tube Gasket 1 1 2 2 23
13 161570808550 Slip Nut 1 1 2 2 23
14 61314C Regulator 1 1 2 2 22
15 50986C Regulator Holder 1 1 2 2 22
16 Basin Galaxy Gray Marblyte (option) 1 1 2 2 -
17 Basin Liner Galaxy Gray Marblyte (option) 1 1 2 2 -
26990C Bottom Cover Standard Reach - 1 1 1 23
26988C Bottom Cover Extended Reach 1 - 1 1 23
55836C Push Arm Actuator 1 1 2 2 20
55991C Push Arm Actuator A.G. 1 1 2 2 20
51546C Bubbler S.S. 1 1 2 2 23
Bubbler EasyFlex (option) 1 1 2 2 -
160270508640 Strainer Plate S.S. 1 1 2 2 23
45400C Strainer Plate A.G. 1 1 2 2 23
161637308640 Drain Plug S.S. 1 1 2 2 23
45398C Drain Plug A.G. 1 1 2 2 23
45683C Drain Tube 1 - 1 1 23
45682C Drain Tube - 1 1 1 23
27006C Basin S.S. 1 1 2 2 23
27342C Basin A.G. 1 1 2 2 23
Basin Golden Sand Marblyte (option) 1 1 2 2 -
Basin Black Onyx Marblyte (option) 1 1 2 2 -
27000C Basin Liner S.S. 1 1 2 2 23
27344C Basin Liner A.G. 1 1 2 2 23
Basin Liner Golden Sand Marblyte (option) 1 1 2 2 -
Basin Liner Black Onyx Marblyte (option) 1 1 2 2 -
Number Required
97793C - 10/01
2
OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F
Parts List Continued
OVL-II OVL-II OVL-II OVL-II Se e
Item Part No. Description ER-Q SR-Q SER-Q ESR-Q Fig.
18 70861C Screw #10-24 x 2 112223
19 55840C Top Plate Actuator 112220
20 55839C Bottom Plate Actuator 112220
27002C Extended Reach Arm S.S. 1 - 1 1 23
21
22 26992C Regulator Mounting Bracket 112221
23 15005C Nut Retaining 112222
24 40045C Hex Nut Unplated 112222
25 27008C Reaction Bracket 112221
26 70856C Screw #10-24 x 0.38 PHMS 112221
27 70854C Rod Pivot 112221
28 50198C Bushing Snap 112221
29 51468C Bumper Regulator Valve Assy 112221
30 22646C Regulator Arm Assembly 112221
31 22635C Arm Regulator Adjustment 112221
32
33
34 55996C Strainer 112217, 18
35 70870C Union 3/8 1 1 - - 17
36 70745C Union 3/8 x 1/4 111117, 18
37 70852C Tee 3/8 - - 1 1 18
N-S 27089C Upper Panel Hanger Bracket 1 1 - - -
N-S 27090C Upper Panel Hanger Bracket - - 1 1 -
N-S 15008C Bubbler Nipple Assembly 1122-
N-S 56092C Tubing Poly (Cut To Length) 1111-
27338C Extended Reach Arm A.G. 1 - 1 1 23
27004C Standard Reach Arm S.S. - 1 1 1 23
27340C Standard Reach Arm A.G. - 1 1 1 23
22797C Upper Panel (OVL-II ER) S.S. 1 - - - 13, 23
27885C Upper Panel (OVL-II ER) A.G. 1 - - - 13, 23
22799C Upper Panel (OVL-II SR) S.S. - 1 - - 13, 23
27887C Upper Panel (OVL-II SR) A.G. - 1 - - 13, 23
26958C Upper Panel (OVL-II SER) S.S. - - 1 - 13, 23
27889C Upper Panel (OVL-II SER) A.G. - - 1 - 13, 23
22795C Upper Panel (OVL-II ESR) S.S. - - - 1 12, 23
27891C Upper Panel (OVL-II ESR) A.G. - - - 1 12, 23
26833C Lower Panel (OVL-II ER-Q/SR-Q) S.S. 1 1 - - 15, 23
27893C Lower Panel (OVL-II ER-Q/SR-Q) A.G. 1 1 - - 15, 23
27026C Lower Panel (OVL-II SER-Q/ESR-Q) S.S. - - 1 1 15, 23
27895C Lower Panel (OVL-II SER-Q/ESR-Q) A.G. - - 1 1 15, 23
NOTE: S.S. means Stainless Steel
A.G. means Aztec Gold
N-S means not shown.
97793C - 10/01
3
OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F
Models
OVL-II SER-Q OVL-II ESR-Q
1. Cut a rectangular wall opening 37-1/2 (953 mm) W x
37-3/4 H (959 mm) and 4-1/2 (114 mm) above the
floor line (see Figure 7). The dimensions are required
to obtain proper rim and bubbler heights for
compliance with ANSI standard A117.1.
2. Reinforce the wall opening on all sides to adequately
support the water fountain. This reinforcement must
support up to 150 lbs. static load and provide a
means for securing the frame assembly in place.
NOTE: Building construction must allow for
adequate air flow on both sides and top of
remote chiller unit a minimum of 4 (102
mm) is required.
3. Install plumbing and electrical rough-ins. A junction
box for a (3) wire, 10 amp branch circuit is provided on
the inside of the chiller. (Standard 120 Volts, 60 Hz,
and single phase.)
Figure 6 OVL-II SER-Q Rough-In
REVERSED CONFIGURATION:
HIGHER UNIT ON THE RIGHT
4. Remove frames and related hardware from
packaging. Release the two shelf rods by cutting
cable ties. Attach the two frames together through the
upright supports with (4) 5/16 x 3/4 (19 mm) long
bolts and nuts (not provided). Tighten securely.
MAKE SURE FRAME CONFIGURATION MATCHES
THE COOLER TO BE INSTALLED
97793C - 10/01
STANDARD CONFIGURATION:
HIGHER UNIT ON THE LEFT
Figure 7 Rough-In Assembly
Dual-Station Mounting Frames
4
Loading...