Halsey Taylor HWF152 Installation Manual
FILTER KIT
HWF152 WATERSENTRY® V KIT (Lead, Sediment, Taste & Odor Reduction)
HWF172 WATERSENTRY® VII KIT (Lead, Cyst, Sediment, Taste & Odor Reduction)
These filter kits are designed to be used with the following
Halsey Taylor products:
HAC-Q, HAC-BL-Q, SCWT-A-Q, S-D-Q
NOTICE: Do not use with water that is microbiologically
unsafe or of unknown quality without adequate
disinfection before or after the system.
General Installation Instructions
1. These filter kits must be installed in compliance with all
state and local laws and regulations governing the
installation and use of this product. Maximum inlet
water temperature 100°F (38°C).
2. Mount filter head in a suitable location, using the filter
mounting bracket and screws supplied. Allow enough
room under the filter head for installation and removal of
filter cartridge (13" minimum).
3. Connect the cold water supply to the filter through a
shut-off valve and 3/8" O.D. tubing (supplied by the
installer). For ease of servicing, the shut-off valve
should be located within easy reach of the filter.
NOTE: The inlet and outlet fitting supplied as
part of the filter head are John Guest Superseal
fittings that accept 3/8" O.D. tubing on the filter
inlet and 1/4" O.D. tubing on the outlet. They may
be used with copper, stainless steel, or semirigid
nylon or polypropylene tubing, with a rated working
pressure equal or greater than encountered in
application. Do not use soft or braided tubing.
4. CAUTION: If supply pressure will ever exceed
100 psi, install a pressure regulator to limit the
inlet pressure to the filter to 100 psi or below.
DO NOT ATTACH HOT WATER LINE TO FILTER.
To make connections on the filter head, loosen locknut.
Push the tube end past both o-rings to a positive stop in
the filter head recess - approx. 1", locknut may have to
be backed out a little more. Screw the locknut hand tight
to seal (See Fig. 1). Ends of tubing must be cut square
and free of burrs and sharp ends that could cut or nick
the o-rings.
5. Connect the outlet of the filter to the inlet of the union
using the 1/4" O.D. poly tubing and 1/4" union supplied.
FIG. 1
FIG. 2
Filter Replacement
1. Turn inlet water valve off.
2. Open dispensing valve to relieve pressure build up in the
system.
3. Remove filter from head by rotating filter counterclock
wise.
4. Remove new filter from carton. Remove protective cap.
Cap may be placed on old filter to reduce the chance of
water spilling from filter housing.
5. Attach filter to filter head by firmly inserting into head and
rotation filter clockwise.
NOTE: The filter head contains an automatic shut-off
valve that stops the flow of water. If the filter is
removed inadvertently without shutting off the
incoming water.
6. Remove filter from carton, remove protective cap, attach
filter to filter head by firmly inserting into head and
rotating filter clockwise.
7. Follow the applicable instructions below for correct
flushing procedure and to complete the installation. the
flushing procedure must be followed to purge air and
fine carbon particles from the system.
8. Read and follow instructions for the installation of the
product to be used with the filter kit.
RATED OPERATING CONDITIONS
Pressure (Min.)
Flow Rate
Temperature (Min.)
NOTE: Performance will vary depending
on local water conditions.
Page 1 96797C (REV. D - 3/98)
20 PSI (1.5 Kg/cm2)
0.75 GPM
40° F (5° C)
Listed below are filters that will fit into the filter head supplied with this kit. The labels on the filters are color coded as noted.
Make certain that the correct filter is being used for application. See Performance Data Sheet supplied with each filter for
complete list of claims.
Table A
REPLACEMENT FILTERS
Filter
Halsey Taylor® WaterSentry
®
Halsey Taylor® WaterSentry® VII
The Halsey Taylor® WaterSentry® VII conforms to ANSI/NSF Standard 42 for reduction of Chlorine - Class I,
Particulate - Class I, and Taste and Odor; ANSI/NSF 53 for reduction of Lead and Cyst.
NOTE: If the flow exceeds the rated flow rate, install a flow restrictor, Part No. 50967C, to limit the flow to .5 gpm.
ITEMIZED PARTS LIST
Item No. Part No. Description
Bracket - Filter Mounting
Screw #8-18 x .50 (13mm) LG. HHSM
Filter Head & Bracket Assembly
Screw #8-18 x .75 (19mm) LG. PH
Tubing - Poly 1/4" (6mm) x 24" LG.
Fitting - Superseal 3/8" (10mm)
Fitting - Superseal 1/4" (6mm)
Filter Assembly
Union - 1/4" (6mm)
Elbow Adapter 1/4" x 3/8"
10
1
2
3
4
5
6
7
8
9
22490C
38417002
51469C
70792C
50801C
70823C
70822C
See Table A
70683C
70819C
Part No. Color Code Description
55895C
V
55897C
White
White
Lead, Sediment, Taste and Odor Reduction Filter
Lead, Cyst Reduction, C.T.O. Filter
2
3
5
9
7
4
1
10
WHEN
REQUIRED
6
FIG. 3
8
* Item No(s). 1, 4, 6, and 7 included with Item No. 3.
FILTER LOCATION
SEE ROUGH-IN
USE DOUBLE BACK TAPE
(2) STRIPS PROVIDED
HAC-Q
Preferred installation-
Filter mounted on
left side panel
Alternate installation-
Filter mounted on
back panel
Page 296797C (REV. D - 3/98)
Loading...