Halsey Taylor HTV-L-R User Manual

These water coolers are certified to

NSF/ANSI 61.

GENERAL

Self-contained, electric refrigerated wall-mounted
water cooler with softly rounded corners and
edges, designed to be easily accessible to
physically challenged individuals. When properly
installed, unit meets state and federal
requirements as defined by the Americans
with Disabilities Act for both children or adults.
Unit is certified to NSF/ANSI 61 and meets
requirements of the Safe Drinking Water Act.
Unit provides 50° F water at 80° F inlet water
and 90° F ambient.

CABINET

Molded two-tone gray space-age polymer with
softly rounded edges. Resistant to impact, wear,
corrosion, heat and sunlight.

COOLER TOP

Non-corrosive stainless steel cooler top,
number 300 series with satin finish resists
stains and corrosion and is easy to maintain.
Anti-splash design reduces splatter. Contour
design and integral strainer insure proper drainage.

BUBBLER

Exclusive one-piece, chrome-plated two­stream mound-building bubbler with
non-removable anti-squirt feature and integral
hood insures a satisfying drink of water.

PUSH BAR ACTUATION MECHANISM

Self-closing light-touch push bars require
minimal pressure to activate.

AUTOMATIC STREAM HEIGHT REGULATOR

Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatically
maintained under line pressures that vary from
20 to 105 psi.

SOLENOID VALVE / INLET STRAINER

Self-closing solenoid valve includes easily
cleaned in-line strainer that screens particles
of 140 microns or larger before they enter
the waterway.

TEMPERATURE CONTROL

Positive sensing thermostat for controlling
temperature of storage tank water. Factory
set at 50° F Adjustable ± 5° F.

STORAGE TANK

Non-pressurized stainless steel
evaporator/storage tank for long life.
Waterways are certified to NSF/ANSI 61,
far exceeding the requirements of the Safe
Drinking Water Act.

REFRIGERATION SYSTEM

Hermetically sealed, positive start compressor
with lifetime lubrication and built-in overload
protection, efficient capillary sizing, large
capacity dryer-strainer, and self-lubricated fan
cools copper/aluminum condenser. System
uses R134A refrigerant. Protected by Halsey
Taylor’s Limited 5 Year Warranty.

VENTILATION

Insure proper ventilation by maintaining
6" (152mm) minimum clearance from
cabinet louvers to wall.

SUGGESTED SPECIFICATIONS

Shall deliver ( ) GPH of 50° F water at
90° F ambient and 80° F inlet water. Shall
have stainless steel basin with integral drain
strainer. Bubbler shall be two-stream, mound
building type. Separate valve and automatic
stream regulator shall be mounted within
cabinet. Refrigeration system shall employ
high efficiency, positive start compressor
using R134A, non-pressurized tank with
totally encapsulated insulation and be
controlled by positive sensing thermostat.
Shall have push-bar water controls. Cooler
shall comply with ANSI 117:1 and ADA for
visual and motion disabilities. The
manufacturer shall certify the unit to meet the
requirements of NSF/ANSI 61, and the Safe
Drinking Water Act. Unit complies with ARI
Standard 1010.

NOTE: Continued product improvement
makes specifications subject to change
without notice. See Halsey Taylor website
for most current spec sheet.

Standard finish is Two-Tone Gray Molded.

Optional Accessories (extra cost)

■■

Water Filter

■■

Easy-Flex™Bubbler

■■

MLP100 In-Wall Support Carrier

■■

Glass Filler (Factory installed only)

■■

Vandal-Resistant Kit

For Stainless Steel Applications Use:

■■

HAC8FS-Q CHILD SS

Optional Features:

■■

Personalized Graphics
(Contact your local representative)

HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523

A1 / 12-2008

MODEL:

■■

HTV4-Q ■■HTV8-Q

■■

HTV-L/R (Less Refrigeration)

Barrier-Free Cooler

halseytaylor.com

HTV-Q BARRIER-FREE SERIES

Model GPH Capacity Base F.L. Shipping Rated
No. Cooled to 50° F* Rate Amps Weight Watt

Ambient Air Temp

Cap. lb. Usage

70°F 80°F 90°F†100°F

HTV4-Q 5.0 4.4 4.0 3.5 4.0 4.0 51 370
HTV8-Q 9.6 8.8 7.6 7.2 7.6 4.0 51 370

* With projector service and tap water at 80° F

†

UL listed and complies with ARI Standard 1010

Trap and service stop not included

JOB NAME:

ENGINEER/CONTRACTOR NAME:

APPROVAL:

DATE:

Printed in the U.S.A.

HTV4-Q, HTV8-Q, HTV-L/R

Barrier-Free Cooler

(CONTINUED)

MOUNTING HEIGHT

Mounting height recommended 30

1

/

4

" from
basin to floor. May be mounted at any desired
height. Check local codes.

MOUNTING INSTRUCTIONS

Mount trap and install service stop to building
supply line. Anchor hanger bracket securely to
wall with six fasteners. To insure proper engaging
of waste line into trap, centerline of trap must
be 7" from wall face. Remove slip nut and gasket
from trap and install on waste line tube. Hang
cooler on bracket and engage waste line tube
into trap inlet. Centerline height of waste outlet
will vary from floor line depending on mounting
height. Connect service stop to solenoid valve
using 3/8" supply tube. Secure bottom of cooler
to wall using holes provided.

Trap and service stop not included.

OPERATING PRESSURES:

Supply water - 20 to 105 psi

ELECTRICAL

Furnished with plug-in, 3-wire grounding type
service cord. Standard 120 volt, 60 Hz, single
phase. Install 120-volt receptacle, rated at
15-amp minimum, to receive 3-wire parallel
blade grounding type male plug.

FRONT VIEW / WALL LAYOUT

SIDE VIEW

Legend:

A = RECOMMENDED WATER SUPPLY

LOCATION. SHUT OFF VALVE
(NOT FURNISHED) TO ACCEPT
3/8" O.D. UNPLATED COPPER TUBE.

B = RECOMMENDED LOCATION FOR

WASTE OUTLET 1-1/4" O.D. DRAIN
C = 1-1/4” TRAP NOT FURNISHED
D = ELECTRICAL SUPPLY (3) WIRE

RECESSED BOX
E = INSURE PROPER VENTILATION BY

MAINTAINING 6" (152 mm) (MIN.)

CLEARANCE FROM CABINET

LOUVERS TO WALL
F = 5/16" BOLT HOLES FOR FASTENING

UNIT TO WALL

* Adult ADA requirement (shown) - 27" (686mm);

Child ADA requirement - 24" (608mm).
Adjust all other measurements accordingly.

When replacing a model ‘HAC’ with a new unit ‘HTV’, installer must cut 1-7/8" from length of cooler
waste line before connecing to trap.

NOTE: Halsey Taylor's recommended orifice
mounting height for children 38" to 46" tall
(approx. four through seven years old) is 23"
from the finished floor.