Halsey Taylor HTV8BLEE-WF-Q User Manual

This water cooler is certified to

NSF/ANSI 61.

GENERAL

Self-contained, electric refrigerated wall-mounted
bi-level water cooler with softly rounded corners
and edges, designed to be easily accessible to
physically challenged individuals. When properly
installed, unit meets state and federal
requirements as defined by the Americans
with Disabilities Act for both children or
adults. Unit is certified to NSF/ANSI 61 and
meets requirements of the Safe Drinking Water
Act. Unit provides 50° F water at 80° F inlet
water and 90° F ambient.

LEAD REDUCTION FILTER

Halsey Taylor Water Cooler With Filter is
equipped with the Aqua Sentry HWF142 lead
reduction system which is designed to remove
cysts, such as cryptrosporidium and giardia,
lead particles and chlorine taste and odor.
The filter has been tested to the following NSF
International standards: NSF/ANSI Standards
42 Chlorine, and Taste and Odor. NSF/ANSI
Standard 53 for Reduction of Lead and Cyst.
Features include Quick-Disconnect fittings on
each end of the in-line filter. The filter contains
a carbon block with lead sorbent media and
the housing is made of rust and corrosion free
plastic. Filter should be replaced every 750
gallons (2839 liters) or approximately 6 months
after installation. Use part number 56191C
when ordering replacement filter.

CABINET

Molded two-tone gray space-age polymer with
softly rounded edges. Resistant to impact, wear,
corrosion, heat and sunlight.

COOLER TOP

Non-corrosive stainless steel cooler top,
number 300 series with satin finish resists
stains and corrosion and is easy to maintain.
Anti-splash design reduces splatter. Contour
design and integral strainer insure proper drainage.

BUBBLER

Exclusive one-piece, chrome-plated two-stream
mound-building bubbler with non-removable
anti-squirt feature and integral hood insures
a satisfying drink of water.

AUTOMATIC ACTUATION

Model HTV8BLEE-WF-Q features infra-red
light beam emitting sensor and a solenoid
valve. Upon interruption of the light beam,
the sensor actuates the solenoid valve to flow
water. User does not have to touch the water
cooler to obtain a drink of water. The water
flow is automatically shut-off after 30 seconds
or earlier if the user leaves the sensing range.
Supplied with a built-in time delay to avoid
nuisance actuation from passers-by.

AUTOMATIC STREAM HEIGHT REGULATOR

Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatically
maintained under line pressures that vary from
20 to 105 psi.

SOLENOID VALVE / INLET STRAINER

Self-closing solenoid valve includes easily
cleaned in-line strainer that screens particles
of 140 microns or larger before they enter
the waterway.

TEMPERATURE CONTROL

Positive sensing thermostat for controlling
temperature of storage tank water. Factory set
at 50° F Adjustable ± 5° F.

STORAGE TANK

Stainless steel evaporator/storage tank for long
life. Waterways are certified to NSF/ANSI 61,
far exceeding the requirements of the Safe
Drinking Water Act.

REFRIGERATION SYSTEM

Hermetically sealed, positive start compressor
with lifetime lubrication and built-in overload
protection, efficient capillary sizing, large
capacity dryer-strainer, and self-lubricated fan
cools copper/aluminum condenser. System
uses R134A refrigerant. Protected by Halsey
Taylor’s Limited 5 Year Warranty.

VENTILATION

Insure proper ventilation by maintaining
6" (152mm) minimum clearance from
cabinet louvers to wall.

SUGGESTED SPECIFICATIONS

Shall deliver 7.6 GPH of 50° F water at 90° F
ambient and 80° F inlet water. Shall have
stainless steel basin with integral drain strainer.
Bubbler shall be two-stream, mound building
type. Separate valve and automatic stream
regulator shall be mounted within cabinet.
Refrigeration system shall employ high
efficiency, positive start compressor using
R134A, evaporator tank with totally
encapsulated insulation and be controlled
by positive sensing thermostat. Shall have
electronic eye water controls for hands-free
operation. Cooler shall comply with ANSI 117:1
and ADA for visual and motion disabilities.
The manufacturer shall certify the unit to meet
the requirements of NSF/ANSI 61, and the
Safe Drinking Water Act. Unit complies with
ARI Standard 1010.

NOTE: Continued product improvement
makes specifications subject to change
without notice. See Halsey Taylor website
for most current spec sheet.

NOTE: Water will only flow from bubbler
when unit has electrical connection.

Standard finish is Two-Tone Gray Molded.

Optional Accessories (extra cost)

■■

Easy-Flex™Bubbler

■■

Glass Filler (Factory installed only)

■■

Cane Touch Apron

■■

Vandal-Resistant Kit

Optional Features:

■■

Personalized Graphics
(Contact your local representative)

HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523

A9 / 8-2007

MODEL HTV8BLEE-WF-Q

Electronic Eye

Bi-Level

Barrier-Free Cooler

halseytaylor.com

HTV-Q BARRIER-FREE SERIES

Model GPH Capacity Base F.L. Shipping Rated
No. Cooled to 50° F* Rate Amps Weight Watt

Ambient Air Temp

Cap. lb. Usage

70°F 80°F 90°F

†

100°F

HTV8BLEE-WF-Q 9.6 8.8 7.6 7.2 7.6 4.0 82 370

* With projector service and tap water at 80° F

†

UL listed and complies with ARI Standard 1010

Trap and service stop not included

JOB NAME:

ENGINEER/CONTRACTOR NAME:

APPROVAL:

DATE:

Printed in the U.S.A.

HTV8BLEE-WF-Q

Electronic Eye Bi-Level
Barrier-Free Cooler
With Filter

(CONTINUED)

MOUNTING HEIGHT

Mounting height recommended 30

1

/

4" from

basin to floor. May be mounted at any desired
height. Check local codes.

MOUNTING INSTRUCTIONS

Mount trap and install service stop to building
supply line. Anchor hanger bracket securely to
wall with six fasteners. To insure proper engaging
of waste line into trap, centerline of trap must
be 7" from wall face. Remove slip nut and gasket
from trap and install on waste line tube. Hang
cooler on bracket and engage waste line tube
into trap inlet. Centerline height of waste outlet
will vary from floor line depending on mounting
height. Connect service stop to solenoid valve
using 3/8" supply tube. Secure bottom of cooler
to wall using holes provided.

Trap and service stop not included.

OPERATING PRESSURES:

Supply water - 20 to 105 psi. In special
circumstances where both sides of unit may be
used simultaneously it is preferable to install
two single filtered units to obtain adequate
stream height regardless of pressure. Does not
apply to non-refrigerated units.

ELECTRICAL

Furnished with plug-in, 3-wire grounding type
service cord. Standard 120 volt, 60 Hz, single
phase. Install 120-volt receptacle, rated at
15-amp minimum, to receive 3-wire parallel
blade grounding type male plug.

FRONT VIEW / WALL LAYOUT

SIDE VIEW

28

7

(PREFFERED
LOCATION)

(ALT. LOCATION)

6

152

152

Legend:

A = RECOMMENDED WATER SUPPLY

LOCATION. SHUT OFF VALVE
(NOT FURNISHED) TO ACCEPT
3/8" O.D. UNPLATED COPPER TUBE.

B = RECOMMENDED LOCATION FOR

WASTE OUTLET 1-1/2" O.D. DRAIN
C = 1-1/2" TRAP NOT FURNISHED
D = ELECTRICAL SUPPLY (3) WIRE

RECESSED BOX (DUPLEX REQUIRED)
E = INSURE PROPER VENTILATION BY

MAINTAINING 6" (152 mm) (MIN.)

CLEARANCE FROM CABINET

LOUVERS TO WALL
F = 5/16" BOLT HOLES FOR FASTENING

UNIT TO WALL

* Adult ADA requirement. 24" (608mm) for child ADA.

Adjust other measurements accordingly.

6

4

1

8

5