Halsey Taylor HTSR -Q User Manual
This water cooler is Classified by
Underwriters Laboratories, Inc.
in accordance with ANSI/NSF 61,
Section 9 - 1997b.
GENERAL
Modular, electric refrigerated, wall-mounted
water cooler designed to be easily accessible
to able-bodied individuals. Unit is certified to
ANSI/NSF 61 Sec. 9 and meets requirements
of the Safe Drinking Water Act. Unit provides
50° F water at 80° F inlet water and 90° F
ambient.
FOUNTAIN
Face-mounted, one-piece, non-corrosive
stainless steel cooler top, number 300 series
with satin finish and contour-formed basin.
BUBBLER
Exclusive one-piece, chrome-plated two-stream
mound-building bubbler with non-removable
anti-squirt feature and integral hood insures a
satisfying drink of water.
PUSH BAR ACTUATION MECHANISM
Self closing, light-touch push bar with raised
letters for the visually impaired.
AUTOMATIC STREAM HEIGHT REGULATOR
Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatically
maintained under line pressures that vary from
20 to 105 psi.
INLET STRAINER
Easily cleaned in-line strainer screen traps
particles of 140 microns or larger before the
enter the waterway.
REFRIGERATION SYSTEM
Hermetically sealed, positive start compressor
with lifetime lubrication and built-in overload
protection, efficient capillary sizing, large
capacity dryer-strainer, and fan cooled
copper/aluminum condenser with self-lubricated
bearing. System uses R134A refrigerant.
Protected by Halsey Taylor’s Limited 5 Year
Warranty.
MOUNTING FRAME
Mounting frame is manufactured of corrosion
resistant, galvanized steel. Open construction
designed for ease of installation. Mounting
frame can be shipped in advance for rough-in
installation.
PANELS
Constructed of stainless steel, number 300
series with satin finish. Removable lower panel
provides access to plumbing and refrigeration
system. Panels overlap wall opening 1⁄2˝.
SUGGESTED SPECIFICATIONS
Shall deliver 7.5 GPH of 50° F water at 90° F
ambient and 80° F inlet water. Fountain shall
include pushbar valve on front, contour-formed
basin to eliminate splashing and standing
water, and rounded corners and edges. Bubbler
shall be chrome plated, two-stream, moundbuilding type. Cooling unit shall have a high
efficiency positive start compressor using
R134A with pressurized counterflow cooling
evaporator/chiller. The manufacturer shall
certify the unit to meet the requirements of
ANSI/NSF 61, Section 9 and the Safe Drinking
Water Act. Shall be certified to meet ARI
Standard 1010.
NOTE: Continued product improvement makes
specifications subject to change without notice.
Standard finish is Stainless Steel
Optional Accessories (extra cost)
■■
Cane Apron
■■
Vandal-Resistant Kit
■■
Water Filter
■■
Lead Filter
■■
Easy-Flex™Bubbler
Each HTSR consists of 3 cartons as follows:
Mounting Frame
Cooling Unit-SJ8
Fountain, Panels & Misc. Parts
Trap and service stop not furnished.
HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
C10 / 9-2002
MODEL: ■■HTSR -Q
Face-Mounted Cooler
Classic
™
Series
www.halseytaylor.com
HT FACE-MOUNTED SERIES
Model GPH Capacity Base F.L. Shipping Rated
No. Cooled to 50° F* Rate Amps Weight Watt
Ambient Air Temp
Cap. lb. Usage
70°F 80°F 90°F 100°F
HTSR-Q 7.3 8.3 7.5 6.8 7.5 4.5 120 400
* With projector service and tap water at 80° F
For additional information on the cooling unit, see the specification sheet for Model SJ8 remote chiller in this catalog.
†
UL listed and certified to meet ARI Standard 1010
Trap and service stop not furnished.
Printed in the U.S.A.
Classic™Series
Face-Mounted Cooler
(CONTINUED)
WALL OPENING
IMPORTANT: It is necessary to create a wall
opening 183⁄4˝ W x 373⁄4˝ H, and 41⁄2˝ above
the floor line.
MOUNTING INSTRUCTIONS
Refer to rough-in for location of plumbing and
electrical sources. The support frame is to be
installed first. The shelf for the water chiller
should be assembled to the wall frame, and
then place chiller into position. Hang upper
fountain panel to hanger on frame. Fountain is
to be attached to panel and wall frame.
Water service line, waste line and electrical is
assembled as required. The bottom panel is
attached last, after a final check for leaks and
correct functions of fountain and chiller. For
details see the installation instructions.
OPERATING PRESSURES:
Supply water-105 psi maximum
ELECTRICAL DATA
Junction box for a (3) wire 10 AMP branch
circuit. Standard 120 volt, 60 Hz, single phase.
TOP & SIDE VIEW
FRONT VIEW
LEGEND:
A = 3/8” O.D. TUBE CONNECT (CHILLER WATER INLET) SHUT OFF VALVE BY OTHERS
B = 1-1/4” O.D. WATER TUBE (ELBOW & TRAP NOT PROVIDED)
C = ELECTRICAL INLET
Loading...