Halsey Taylor HTSER-Q User Manual
This water cooler is certified to
NSF/ANSI 61.
GENERAL
Modular, electric refrigerated, bi-level wallmounted water cooler designed to be easily
accessible to physically challenged and ablebodied individuals. When properly installed, unit
meets state and federal requirements as
defined by the Americans with Disabilities Act.
Unit is certified to NSF/ANSI 61 and meets
requirements of the Safe Drinking Water Act.
Unit provides 50° F water at 80° F inlet water
and 90° F ambient.
FOUNTAIN
Face-mounted, one-piece, non-corrosive
stainless steel cooler top, number 300 series
with satin finish and contour-formed basin.
BUBBLER
Exclusive one-piece, chrome-plated two-stream
mound-building bubbler with non-removable
anti-squirt feature and integral hood insures a
satisfying drink of water.
PUSH BAR ACTUATION MECHANISM
Self closing, light-touch push bars with raised
letters for the visually impaired.
AUTOMATIC STREAM HEIGHT REGULATOR
Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatically
maintained under line pressures that vary from
20 to 105 psi.
INLET STRAINER
Easily cleaned in-line strainer screen traps
particles of 140 microns or larger before they
enter the waterway.
REFRIGERATION SYSTEM
Hermetically sealed, positive start compressor
with lifetime lubrication and built-in overload
protection, efficient capillary sizing, large
capacity dryer-strainer, and fan cooled
copper/aluminum condenser with self-lubricated
bearing. System uses R134A refrigerant.
Protected by Halsey Taylor’s Limited 5 Year
Warranty.
MOUNTING FRAME
Mounting frame is manufactured of corrosion
resistant, galvanized steel. Open construction
designed for ease of installation. Mounting
frame can be shipped in advance for rough-in
installation.
PANELS
Constructed of stainless steel, number 300
series with satin finish. Removable lower panel
providing access to plumbing and refrigeration
system. Panels overlap wall opening
1
/
2˝
.
SUGGESTED SPECIFICATIONS
Shall deliver 7.5 GPH of 50° F water at 90° F
ambient and 80° F inlet water. Fountain shall
include push bar valves on front, contourformed basin to eliminate splashing and
standing water, and rounded corners and
edges. Bubbler shall be chrome plated, twostream, mound- building type. Cooling unit shall
have a high efficiency positive start compressor
using R134A, with pressurized counterflow
cooling evaporator/chiller. Cooler shall comply
with ANSI 117:1 and ADA for visual and motion
disabilities. The manufacturer shall certify the
unit to meet the requirements of NSF/ANSI 61,
and the Safe Drinking Water Act. Unit complies
with ARI Standard 1010.
NOTE: Continued product improvement makes
specifications subject to change without notice.
See Halsey Taylor website for most current
spec sheet.
Standard finish is Stainless Steel
Optional Accessories (extra cost)
■■
Cane Touch Apron
■■
Vandal-Resistant Kit
■■
Water Filter
■■
Easy-Flex™Bubbler
Each HTSER-Q consists of 3 cartons
as follows:
Mounting Frame
Cooling Unit-SJ8
Fountain, Panels & Misc. Parts
HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
A34 / 1-2005
MODEL:■■HTSER-Q
Barrier-Free Cooler
Classic™Series Bi-Level
www.halseytaylor.com
HT BARRIER-FREE SERIES
Model GPH Capacity Base F.L. Shipping Rated
No. Cooled to 50° F* Rate Amps Weight Watt
Ambient Air Temp
Cap. lb. Usage
70°F 80°F 90°F†100°F
HTSER-Q 9.3 8.3 7.5 6.8 7.5 3.5 133 325
* With projector service and tap water at 80° F
For additional specification of the cooling unit, see specification sheet for Model SJ8 Remote in this catalog.
†
UL listed and complies with ARI Standard 1010
Trap and service stop not included
Halsey Taylor Barrier-Free Drinking
Fountains and Water Coolers conform
to The Americans with Disabilities Act
and American National Standards
Institute Specifications.
3-1/8"
80mm
1-1/8"
29mm
A
5-5/8"
143mm
9-3/8"
238mm
BACK WALL
LINE
B
5/8"
16mm
10"
264mm
19"
483mm
20-3/8"
518mm
12-1/2"
318mm
12-1/2"
318mm
3-5/8"
92mm
38-1/2"
978mm
6-1/4"
159mm
40"
1016mm
33-1/16"
839mm
20-7/16"
519mm
C
FINISHED FLOOR
27"
686mm
ADA
REQUIREMENT
28-3/16"
716mm
35-1/8"
892mm
2-1/16"
52mm
11"
279mm
1"
26mm
4-1/2"
114mm
8"
203mm
WALL LINE
12"
306mm
MINIMUM DEPTH
Printed in the U.S.A.
Barrier-Free Bi-Level
Cooler
(CONTINUED)
WALL OPENING
IMPORTANT: It is necessary to create a wall
opening 37
1
/
2
" W x 37
3
/4
" H and 4
1
/
2
" above the
floor line.
MOUNTING INSTRUCTIONS
Refer to rough-in for location of plumbing and
electrical sources. The support frame is to be
installed first. The shelf for the water chiller
should be assembled to the wall frame, and
then place chiller into position. Hang upper
fountain panel to hanger on frame. Fountain is
to be attached to panel and wall frame. Water
service lines, waste lines and electrical are
assembled as required. The bottom panel is
attached last, after a final check for leaks and
correct functions of fountains and chiller.
(For details see the installation instructions.)
Installation requires trap to be installed in
wall. Trap and service stop not included.
OPERATING PRESSURES:
Supply water - 105 psi maximum
ELECTRICAL DATA
Junction box for a (3) wire 10 AMP branch
circuit. Standard 120 volt, 60 HZ, single phase.
FRONT VIEW
TOP & SIDE VIEW
LEGEND:
A = 3/8" O.D. TUBE CONNECT (CHILLER WATER INLET) SHUT OFF VALVE BY OTHERS
B = 1-1/4" O.D. DRAIN TUBE (ELBOW & TRAP NOT PROVIDED)
C = ELECTRICAL INLET
Loading...