Halsey Taylor HTSEBP FR User Manual
This fountain is certified to
NSF/ANSI 61.
GENERAL
Two face-mounted fountains, one-piece,
non-corrosive stainless steel number 300
series with brushed satin finish. Contourformed basins with rounded corners and edges
reduces splatter, insures proper drainage and
prevents standing waste water. Designed to be
easily accessible to both physically challenged
and able-bodied individuals. Ideally suited for
installation in public areas. Model meets state
and federal requirements as defined by the
Americans with Disabilities Act.
FREEZE-RESISTANT VALVE SYSTEM
Freeze-resistant system features box that
installs behind non-freezing wall for housing
water connection from the stop to the strainer.
BUBBLER
Exclusive one-piece, chrome-plated two-stream
mound-building bubbler with non-removable
anti-squirt feature and integral hood insures a
satisfying drink of water.
PUSHBUTTON ACTUATION MECHANISM
Self-closing, vandal-resistant pushbutton does
not require grasping or twisting.
PANEL
Constructed of stainless steel, No. 300 series
with satin finish.
AUTOMATIC STREAM HEIGHT REGULATOR
Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatically
maintained under line pressures that vary from
20 to 105 psi.
INLET STRAINER
Easily cleaned in-line strainer screen traps
particles of 140 microns or larger before they
enter the waterway.
WATER INLET
3/8" O.D. Tubing into freeze-resistant box.
DRAIN OUTLET
1-1/4" waste outlet located in freeze-resistant
valve system.
SUGGESTED SPECIFICATIONS
Fountain shall include pushbuttons on the front,
contour-formed basins to eliminate splashing and
standing water, and shall have rounded corners
and edges. Each projector shall be two-stream,
mound-building type with integral hood guard and
anti-squirt feature. Fountain shall comply with
ANSI 117:1 and ADA for visual and motion
disabilities. The manufacturer shall certify the unit
to meet the requirements of NSF/ANSI 61, and
the Safe Drinking Water Act.
Note: Continued product improvement makes
specifications subject to change without notice.
See Halsey Taylor website for most current
spec sheet.
Standard Finish is Stainless Steel
Optional Accessories (extra cost)
■■
Cane Touch Apron
■■
Vandal-Resistant Kit
Each HTSEBP FR consists of 2 cartons
of the following:
Fountain, Panel and Misc. Parts
Freeze-Resistant Valve System
Service stop not included.
Copper tube to water supply connection not
included
Shipping weight: 94 lbs.
HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
B18 / 1-2005
MODEL: ■■HTSEBP FR
Barrier-Free Fountain
Classic
™
Series Bi-Level
Freeze-Resistant
www.halseytaylor.com
Halsey Taylor Barrier-Free Drinking
Fountains and Water Coolers conform
to The Americans with Disabilities Act
and American National Standards
Institute Specifications.
Printed in the U.S.A.
Freeze-Resistant
Classic™ Series
Barrier-Free
Bi-Level Fountain
(CONTINUED)
MOUNTING INSTRUCTIONS
Refer to diagrams for rough-in of
freeze-resistant system and plumbing.
For wall support required locations
see installation instructions provided
with panel and fountains. Mount wall
plate assembly to wall per the
installation instructions.
Hang fountain panel over the wall plate
assembly. Attach fountains to wall plate
assembly. Water service lines and waste line
are to be assembled as required. Final check
for leaks and correct functions of fountain
should be made. (See installation instructions
for full details.)
Freeze resistant box must be installed on
interior non-freezing wall.
CAUTION – Fountain must be securely
bolted to wall.
OPERATING PRESSURES:
Supply water - 105 psi maximum
27"
*
(686mm)
WALL LAYOUT
SIDE VIEW
FRONT VIEW
LEGEND:
A = 7/8" DIA. (22mm) HOLE FOR WATER INLET
B = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
(ELBOW AND TRAP PROVIDED)
C = 1/4" (6mm) DIA. HOLES FOR MOUNTING PLATE TO WALL
*
ADA REQUIREMENT
NOTE: A service supply stop (not included) must be installed at the fountain inlet line.
Loading...