Halsey Taylor HTHBSM-WF User Manual
Filtered
H
YDROBOOST
™
MODELS: HTHBSM-WF
* Rated for Indoor Use Only
These water coolers are certified to
NSF/ANSI 61.
GENERAL
Botte Filling Station designed for mounting
directly onto a wall surface for applications with
limited wall depth. When properly installed, unit
meets the reach range guidelines as defined
by the American with Disabilities Act (ADA).
If desired, unit can be paired with a remote
chiller to provide a chilled drink of water.
BOTTLE FILLING
Quick fill rate is 1.5 gallons per minute and
1.1 gallons per minute when paired with remote
chiller. Laminar flow provides a clean fill with
minimal splash and easy maintenance.
SENSOR ACTIVATED
User interface design makes touchless operation
intuitive. Equipped with automatic 20-second
shut-off timer.
SILVER ION ANTI-MICROBIAL
PROTECTION
Key plastic components are integrated with
silver ion anti-microbial protection to inhibit
growth of mold and mildew.
LEAD REDUCTION FILTER WITH
FILTER LIFE INDICATOR
Equipped with the HWF3000 WaterSentry
Plus Filter which is designed to reduce lead
particles and chlorine. Also reduces odors and
discoloration from incoming water. Features
include Quick-Disconnect, 1/4 turn installation.
Automatic inlet shut-off valve that closes when
filter is removed. High-grade filter is made
with activated carbon and patented ATS
lead-removal media.
Green, yellow, and red LEDs visually indicate
when filter maintenance is required. For service
replacement, order as:
55898C - Filter single
55898C_3PK - Filter three pack
55898C_12PK - Filter twelve pack
55898C_24PK - Filter twenty-four pack
55898C_48PK - Filter forty-eight pack
GREEN COUNTER™
Visually displays count of 20 oz. plastic bottles
saved from landfills.
MOUNTING
Includes a sturdy hanger bracket to provide
proper support of the unit on the wall surface.
®
SUGGESTED SPECIFICATIONS
Bottle Filling unit shall be designed to mount
directy on the wall surface. Constructed of 18
gauge Type 300 series stainless steel and ABS
plastic. Shall include electronic sensor for notouch activation with automatic 20-second shut
off timer. Shall provide 1.1-1.5 gpm flow rate
with laminar flow to minimize splashing. Shall
include antimicrobial protect plastic components
to prevent mold and mildew. Shall include the
WaterSentry
42 and 53 for lead reduction, with visual monitor
to indicate when replacement is necessary. Shall
meet ADA guidelines for reach ranges, when
properly installed. Shall be lead-free design which
meets Safe Drinking Water Act and is certified to
NSF/ANSI 61 and California AB1953. Shall be
certified to UL399 and CAN/CSA 22.2 No. 120.
®
Plus filter, certified to NSF/ANSI
Surface Mount
Bottle Filling Station
HTHBSM-WF
Ships in a single carton
NOTE: Continued product improvement makes
specifications subject to change without
notice. See Halsey Taylor website for most
current spec sheet.
JOB NAME:
ENGINEER/CONTRACTOR NAME:
APPROVAL:
DATE:
HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
halseytaylor.com
THIRD-PARTY CERTIFIED TO:
* UL399 & CAN/CSA 22.2 NO. 120
* NSF/ANSI 61-ANNEX G, AB 1953
9-2011
MODEL HTHBSM-WF
Filtered
HYDROBOOS
T
™
Surface Mount
Bottle Filling Station
* Rated for Indoor Use Only
D
9 1/2"
241mm
25 7/16"
646mm
12"
305mm
D
7"
178mm
D
OPERATING PRESSURES:
Supply water - 20 to 105 psi maximum
17 13/16"
453mm
7"
178mm
D
D
B
A
3 1/16"
77mm
46 7/16"
1180mm
ELECTRICAL:
Hydroboost station equipped with electric
cord and three-prong molded rubber plug for
use with 15-amp minimum receptacle.
Rated at 115 volt, 60Hz, single phase.
8 3/16"
208mm
5 3/8"
136mm
2 7/8"
73mm
D
34 7/16"
875mm
32 15/16"
837mm
1 3/8"
35mm
FINISHED
WALL
27"
686mm
28"
712mm
8 7/8"
225mm
6 1/4"
159mm
120V POWER CORD
(18" MIN. LENGTH)
FINISHED FLOOR
33 1/2"
851mm
30 1/16"
763mm
C
FIG. 1
LEGEND:
A = RECOMMENDED WATER SUPPLY LOCATION ; 1/2" IPS MAXIMUM PIPE SIZE. SERVICE STOP VALVE NOT FURNISHED.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. MAXIMUM PIPE SIZE.
C = ELECTRICAL OUTLET, THREE (3) CONDUCTOR GROUNDED. LOCATE WITHIN SAFE REACH OF POWER CORD.
D = 7/16" X 3/4" OBROUND MOUNTING HOLES FOR FASTENING BACKPLATE TO WALL.
Specifications and measurements are subject to change without notification.
Please visit halseytaylor.com for most current version.
Printed in the U.S.A.
Loading...