Halsey Taylor HTHBHVRBLR8-NF, HTHBHVR8-NF1A Installation Manual
HTHBHVR-NF*A, HTHBHVRBL-NF*A, HTHBHVRBLR-NF*A,
HTHBHVR8-NF*1A, HTHBHVR8BL-NF*1A, HTHBHVR8BLR-NF*1A
Installation/Care/Use Manual
HTHBHVR8-NF Factory Prep
Hydroboost Bottle Filling Station and Cooler
IMPORTANT
THIS IS AN INDOOR APPLICATION ONLY.
ALL SERVICE TO BE PERFORMED BY AN
AUTHORIZED SERVICE PERSON.
TOOLS REQUIRED
BUT NOT PROVIDED:
SAFETY GLASSES
GLOVES
ELECTRIC DRILL
3/4” WRENCH OR CRECENT WRENCH
UTILITY KNIFE
TAPE MEASURE
PENCIL
CENTER PUNCH
1/2” SOCKET & RATCHET WRENCH
5/32” ALLEN WRENCH
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER
LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY
FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT
OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY
DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM. WE SUGGEST THAT THE BOTTLE FILLING
STATION AND WATER COOLER BE PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI).
INSTALLER
HTHBHVR8-NF Bottle Fillers are among the easiest to install on the market today.
To insure you install these models easily and correctly, PLEASE READ THESE
SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK
YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND
OTHER APPLICABLE CODES. After installation, leave these instructions with the
Fountain for future reference.
Page 1
98988C (Rev. A - 5/12)
HTHBHVR-NF*A, HTHBHVRBL-NF*A, HTHBHVRBLR-NF*A,
HTHBHVR8-NF*1A, HTHBHVR8BL-NF*1A, HTHBHVR8BLR-NF*1A
5-1/8"
131mm
18-9/16"
472mm
66mm
2-5/8"
6-1/4"
159mm
1-1/2"
38mm
C
6-3/4"
171mm
12-5/16"
312mm
1298mm
51-1/8"
HTHBHVR8-NF
7"
178mm
16-5/16"
414mm
7"
178mm
HANGER BRACKET
48"
1219mm
18-1/2"
470mm
1-1/4"
32mm
1-1/4"
32mm
8"
203mm
27"
686mm
*
31-15/16"
811mm
RIM HEIGHT
33-1/16"
840mm
HEIGHT
ORIFICE
2-9/16"
185mm
E
4-9/16"
116mm
7-1/4"
2-1/2"
11/16"
18mm
65mm
F
63mm
13-7/8"
352mm
89mm
3-1/2"
114mm
2-7/16"
4-1/2"
63mm
10"
254mm
FINISHED FLOOR
5"
127mm
MOUNTING
5/16"
8mm
O
HOLES (3 PL)
98988C (Rev. A - 5/12)
D
E
OBROUND HOLE (5 PL)
1/4" X 1/2" (6mm X 13mm)
B
49-1/2"
1257mm
A
18-3/8"
467mm
* REDUCE HEIGHT BY 3” FOR INSTALLATION OF CHILDRENS ADA COOLER
LEGEND:
A = RECOMMENDED WATER SUPPLY LOCATION 3/8” O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2” (38mm)
OUT FROM WALL. SHUT OFF VALVE NOT FURNISHED.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN.
C = 1-1/4” TRAP NOT FURNISHED.
D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX, DUPLEX OUTLET REQUIRED.
E = INSURE PROPER VENTILATION BY MAINTAINING 6” (152mm) MIN. CLEARANCE FROM CABINET LOUVER TO WALL.
21-3/8"
543mm
25"
635mm
31"
788mm
F = 7/16” BOLT HOLES FOR FASTENING UNITS TO WALL.
Single Rough-In
Fig. 1
Page 2
HTHBHVR-NF*A, HTHBHVRBL-NF*A, HTHBHVRBLR-NF*A,
HTHBHVR8-NF*1A, HTHBHVR8BL-NF*1A, HTHBHVR8BLR-NF*1A
5-1/8"
131mm
18-9/16"
472mm
HANGER
BRACKET
2-5/8"
67mm
8"
HEIGHT
39-9/16"
1005mm
ORIFICE
48"
1219mm
C
4-1/8"
203mm
33-1/16"
840mm
HEIGHT
ORIFICE
105mm
31-15/16"
811mm
RIM HEIGHT
6-3/4"
171mm
12-5/16"
313mm
27"
686mm
*
7"
178mm
HTHBHVRBL8-NF
16-5/16"
414mm
7"
178mm
18-1/16"
459mm
1-3/8"
35mm
51-1/8"
1298mm
25-1/8"
HOLES
5/16"
8mm
O
(3 PL)
18-1/2"
470mm
L
C
5-3/4"
146mm
5-3/4"
146mm
1/4" X 1/2" (6mm X 13mm)
OBROUND HOLE (5 PL)
1-1/4"
32mm
D
1-1/4"
32mm
L
C
4-9/16"
116mm
A
11/16"
18mm
638mm
20-1/8"
511mm
18-3/4"
E
F
476mm
13-7/8"
352mm
3-1/2"
89mm
4-1/2"
114mm
6-1/4"
159mm
B
2-7/16"
63mm
10"
254mm
FINISHED FLOOR
* REDUCE HEIGHT BY 3” FOR INSTALLATION OF CHILDRENS ADA COOLER
LEGEND:
A = RECOMMENDED WATER SUPPLY LOCATION 3/8” O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2” (38mm)
OUT FROM WALL. SHUT OFF VALVE NOT FURNISHED.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN.
C = 1-1/2” TRAP NOT FURNISHED.
D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX, DUPLEX OUTLET REQUIRED.
E = INSURE PROPER VENTILATION BY MAINTAINING 6” (152mm) MIN. CLEARANCE FROM CABINET LOUVER TO WALL.
F = 7/16” BOLT HOLES FOR FASTENING UNITS TO WALL.
2-9/16"
1-3/8"
35mm
HOLES
5/16"
8mm
O
(5 PL)
E
6-1/2"
165mm
F
7-1/4"
185mm
65mm
5"
127mm
20-3/8"
518mm
37-1/2"
952mm
Two -Level Rough-In
Fig. 2
Page 3
98988C (Rev. A - 5/12)
Loading...