Halsey Taylor HTHBHVR8BL-NF User Manual

Vandal-Resistant

HYDROBOOST

™

Models:

HTHBHVR8BL-NF
HTHBHVRBL-NF

GENERAL

Complete water station including HydroBoost™ bottle filling station
and HVR water cooler.

HVR WATER COOLER

Self-contained, stainless steel, wall mount single level water cooler.
Model HTHBHVR8BL-NF delivers chilled water; HTHBHVRBL-NF
delivers ambient drinking water. Vandal-resistant one-piece, chrome­plated bubbler with integral hood guard design to prevent tampering,
airborne deposits and contamination. Automatic stream height regula­tor is located inside unit to prevent tampering. A constant stream
height is automatically maintained under line pressures that vary from
20 to 105 psi. Includes self-closing vandal-resistant pushbutton which
does not require grasping or twisting. Type 300 series stainless steel
cooler top with satin finish to resist stains and corrosion. Basin
includes anti-splash ridge and contoured to insure proper drainage.

HYDROBOOST™ BOTTLE FILLING STATION

Stainless steel design for tamper-resistance. Pushbutton activation
enhanced with embossed user graphics. Quick fill rate is 1.1 gallons
per minute on chilled model and 1.5 gpm on ambient model. Laminar
flow provides a clean fill with minimal splash and easy maintenance.
30-second shut-off timer for water flow. Recessed orifice to prevent
cross-contamination.

GREEN COUNTER™

Visually displays count of plastic water bottles saved from the landfills.
Protected behind tempered glass.

INLET STRAINER

Easily cleaned in-line strainer screen traps particles of 140 microns
or larger before they enter the waterway.

REFRIGERATION SYSTEM (Model HTHBHVR8BL-NF Only)

Unit provides 8GPH of 50

o

F inlet water. Hermetically sealed, positive start compressor

80
with lifetime lubrication and built-in overload protection, efficient
capillary sizing, large capacity dryer-strainer and self-lubricated fan
cools copper/ aluminum condenser. R-134a refrigerant. Protected
by Halsey Taylor’s Limited Warranty.

TEMPERATURE CONTROL

Positive sensing thermostat for controlling temperature of storage
tank water. Factory set at 50

o

F drinking water at 90oF ambient air and

o

F adjustable + 5oF.

HVR Bi-Level Cooler

with Bottle Filler

SUGGESTED SPECIFICATION

Model HTHBHVR8BL-NF shall deliver 8GPH of

o

50 F drinking water at 90 F ambient air and 80 F
inlet water. Model HTHBHVRBL-NF shall deliver
non-chilled drinking water. Shall have stainless
steel construction. Shall include vandal-resistant,
one-piece bubbler with integral hood. Shall
include vandal-resistant pushbutton activation
with embossed user graphics. Shall include
30-second auto shut-off for water flow. Shall
include Green Counter with tempered glass
protective covering. Shall provide 1.1-1.5 gpm
with laminar flow for minimal splash and recessed
orifice to prevent cross-contamination. Cooler
shall have stainless steel basin with anti-splash
ridge and removeable drain strainer. Shall
comply with ADA standards, UL399, CAN/CSA

22.2 No. 120, NSF/ANSI 61 and NSF/ANSI

oo

372.

Trap and service stop not included.

NOTE: Continued product improvement makes specification
sheets subject to change without notice.

halseytaylor.com

HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523

JOB NAME: ______________________

________________________________

________________________________

ENGINEER/CONTRACTOR NAME:

________________________________

APPROVAL: _____________________

DATE: __________________________

6-2012

HTHBHVR8BL-NF and HTHBHVRBL-NF

Bi-Level HVR Cooler with
HydroBoost™ Bottle Filler

(CONTINUED)

O

(5 PL)

37-1/2"
952mm

5/16"
8mm

20-3/8"
518mm

1-3/8"
35mm

HOLES

6-1/2"
165mm

7-1/4"
185mm

5"
127mm

OPERATING PRESSURES

Supply water – 105 psi maximum
Minimum 40 psi supply line pressure required in special
circumstances when both units are in use simultaneously
to ensure adequate flow.

16-5/16"

7"
178mm

1-1/4"
32mm

6-1/4"
159mm

414mm

C

L

18-1/2"
470mm

D

3-1/2"
89mm

4-1/2"
114mm

E

F

2-9/16"
65mm

5-3/4"
146mm

4-9/16"
116mm

18-1/16"
459mm

1-3/8"
35mm

5-3/4"
146mm

C

L

11/16"
18mm

2-7/16"
63mm

10"
254mm

FINISHED FLOOR

B

7"
178mm

5/16"

O

8mm

(3 PL)

1-1/4"
32mm

1/4" X 1/2" (6mm X 13mm)
OBROUND HOLE (5 PL)

A

E

F

20-1/8"
511mm

18-3/4"
476mm

13-7/8"
352mm

ELECTRICAL

HydroBoost Station equipped with plug-in, 3-wire ground
type service cord. Install 120-volt receptacle, rated at
15-amp minimum, to receive 3-wire parallel blade
grounding type male plug.

HOLES

51-1/8"
1298mm

48"
1219mm

39-9/16"
1005mm

ORIFICE
HEIGHT

8"
203mm

4-1/8"
105mm

25-1/8"
638mm

33-1/16"
840mm

ORIFICE

HEIGHT

RIM HEIGHT

31-15/16"
811mm

*

27"
686mm

18-9/16"
472mm

2-5/8"
67mm

HANGER

BRACKET

C

12-5/16"
313mm

5-1/8"
131mm

6-3/4"
171mm

* REDUCE HEIGHT BY 3” FOR INSTALLATION OF CHILDRENS ADA COOLER

LEGEND:
A = RECOMMENDED WATER SUPPLY LOCATION 3/8” O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2” (38mm)
OUT FROM WALL. SHUT OFF VALVE NOT FURNISHED.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN.
C = 1-1/2” TRAP NOT FURNISHED.
D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX, DUPLEX OUTLET REQUIRED.
E = INSURE PROPER VENTILATION BY MAINTAINING 6” (152mm) MIN. CLEARANCE FROM CABINET LOUVER TO WALL.
F = 7/16” BOLT HOLES FOR FASTENING UNITS TO WALL.

Printed in the U.S.APage 2