Halsey Taylor HTHB-8-NF User Manual
Filterless
H
YDROBOOST
™
MODELS: HTHB-8-NF HTHB-LR-NF
* Rated for Indoor Use Only
These water coolers are certified to
NSF/ANSI 61.
GENERAL
In-wall, recessed design for stand-alone
applications or paired with Halsey Taylor
Contour™ and OVL-II™ fountains to create the
ultimate high end water station. When properly
installed, unit meets reach range guidelines as
defined by the Americans with Disabilities Act.
BOTTLE FILLING
Quick fill rate is 1.5 gallons per minute for
non-refrigerated models and 1 gallon per
minute for refrigerated models. Laminar flow
provides a clean fill with minimal splash and
easy maintenance.
SENSOR ACTIVATED
User interface design makes touchless operation
intuitive. Equipped with automatic 20-second
shut-off timer.
SILVER ION ANTI-MICROBIAL
PROTECTION
Key plastic components are integrated with
silver ion anti-microbial protection to inhibit
growth of mold and mildew.
GREEN COUNTER™
Visually displays count of 20 oz. plastic bottles
saved from landfills.
MOUNTING FRAME
Mounting frame is manufactured of corrosion
resistant, galvanized steel. open construction
designed for ease of installation. Mounting
frame can be shipped in advance for rough-in
installation.
PANEL SYSTEM
Designed with hinged top and bottom stainless
steel panels for easy access and service.
Refrigerated model includes louvered panel.
Non-refrigerated models includes solid panel.
REFRIGERATION SYSTEM
(Model HTHB-HAC-NF)
Hermetically sealed, positive start compressor
with lifetime lubrication and built-in overload
protection, efficient capillary sizing, large
capacity dryer-strainer, and self-lubricated fan
cools copper/aluminum condenser. System
uses R134A refrigerant. Protected by Halsey
Taylor’s Limited 5 Year Warranty.
SUGGESTED SPECIFICATIONS
Model HTHB-8-NF provides 8.0 gph of 50º F
water at 90º F ambient and 80º F inlet water.
Model HTHB-LR-NF is non-refrigerated and
provides ambient water. Shall be recessed
design and constructed of 18 gauge Type 300
series stainless steel and ABS plastic. Shall
include electronic sensor for no-touch
activation with automatic 20-second shut-o
timer. Shall provide 1 - 1.5 gpm flow rate with
laminar flow to minimize splashing. Shall
include antimicrobial protected plastic
components to prevent mold and mildew.
Shall meet ADA guidelines for reach ranges,
when properly installed. Shall be lead-free
design which meets Safe Drinking Water Act
and is certified to NSF/ANSI 61 and California
AB1953. Shall be certified to UL399 and
CAN/SA 22.2 No. 120.
NOTE: Continued product improvement makes
specifications subject to change without
notice. See Halsey Taylor website for most
current spec sheet.
In-Wall Recessed
Bottle Filling Station
HTHB-8-NF
Stainless Steel Finish Only
ff
Consists of multiple cartons as follows:
HYDROBOOST Station with Panels
Mounting Frame
Cooling unit - SJ8-Q (Model HTHB-8-NF only)
HTHB-LR-NF
JOB NAME:
ENGINEER/CONTRACTOR NAME:
APPROVAL:
DATE:
halseytaylor.com
HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
THIRD-PARTY CERTIFIED TO:
* UL399 & CAN/CSA 22.2 NO. 120
* NSF/ANSI 61-ANNEX G, AB 1953
A45 /4-2011
MODELS HTHB-8-NF & HTHB-LR-NF
8 1/8"
( 206mm )
9 3/8"
( 238mm )
1 1/8"
( 29mm )
3"
( 79mm )
18 3/4"
( 476mm )
4"
( 102mm )
12" *
( 305mm )
MINIMUM
DEPTH
25 1/4"
( 641mm )
27"
( 681mm )
MFWS100
Filterless
HYDROBOOS
In-Wall Recessed
Bottle Filling Station
* Rated for Indoor Use Only
FRAME
5/16" SCREWS OR BOLTS
(10 REQ'D-NOT PROVIDED)
HOOK RODS (2)
P/N 101567443730
SCREWS OR BOLTS
(NOT PROVIDED)
ANDARD HEIGHT
INSTALL (2) SCREWS
(P/N 111008343890) IN FRAME
BEFORE INSTALLING IN OPENING
STANDARD HEIGHT
FRONT VIEW / WALL LAYOUT
1 3/16"
( 30mm )
T
™
OPERATING PRESSURES:
Supply water - 105 psi maximum
ELECTRICAL
Hydroboost station equipped with electric
cord and three-prong molded rubber plug for
Minimum 40 psi supply line pressure required
in special circumstances when both sides of
bilevel are in use simultaneously to ensure
adequate stream height. Does not apply to
use with 15-amp minimum receptacle.
For the cooling unit, a junction box for a (3)
wire , 10 amp branch circuit is provided.
Rated at 115 volt, 60 Hz, single phase.
non-refrigerated units.
DOUBLE STUD OR 3 INCHES (76 mm)
BETWEEN MOUNTING FRAMES
IF PLACED NEXT TO ANOTHER
FOUNTAIN OR WALL
WOOD OR STEEL
FRAME SHOWN
(NOT PROVIDED)
40"
1016mm
4 1/2
114mm
CHILLER SHELF
P/N 27638C
19 3/4"
( 502mm )
17 3/8"
( 441mm )
1 3/16"
( 30mm )
18 3/4"
476mm
1"
25mm
ELECTRICAL INLET
LOCATION ON CHILLER
8"
203mm
TO FLOOR LINE
3/8" O.D. TUBE CONNECT
(CHILLER WATER INLET)
SHUT OFF VALVE BY OTHERS
DOUBLE STUD OR 3" (76mm)
BETWEEN MOUNTING FRAMES
5 1/8"
IF PLACED NEXT TO ANOTHER
130mm
FOUNTAIN OR WALL
1 3/16"
( 30mm )
19 3/4"
( 502mm )
17 3/8"
( 441mm )
FLOOR LINE
BACK OF WALL TO
BE 12" (305mm)
MIN DEPTH
1 3/16"
( 30mm )
1/4" O.D. TUBE CONNECT
(CHILLER WATER OUTLET)
3/8" O.D. TUBE CONNECT
(CHILLER WATER INLET)
SHUT OFF VALVE BY OTHERS
DOUBLE STUD OR 3" (76mm)
BETWEEN MOUNTING FRAMES
IF PLACED NEXT TO ANOTHER
FOUNTAIN OR WALL
* 7" minimum depth
for non-refrigerated models
SIDE VIEW
1 1/8"
( 29mm )
FILTER LOCATION
(OPTIONAL)
3"
( 79mm )
( 102mm )
12"
( 305mm )
MINIMUM
DEPTH
1/4" O.D. TUBE CONNECT
(CHILLER WATER OUTLET)
8 1/8"
( 206mm )
4"
9 3/8"
( 238mm )
18 3/4"
( 476mm )
38 7/8"
( 987mm )
FINISHED FLOOR
20 3/8"
( 518mm )
20 7/16"
( 519mm )
3 1/2"
( 89mm )
4 1/2"
( 116mm)
BACK WALL LINE
1-1/4" (32MM)
WASTE TUBE
FURNISHED
25 7/8"
( 657mm )
2 7/8"
20 3/8"
( 73mm )
( 518mm )
ELECTRICAL
20 7/16"
INLET
( 519mm )
FINISHED FLOOR
1 1/8"
( 29mm )
27"
( 681mm )
11"
( 279mm )
25 1/4"
( 641mm )
3 1/2"
( 89mm )
4 1/2"
( 116mm)
BACK WALL LINE
2 7/8"
( 73mm )
1-1/4" (32MM)
WASTE TUBE
FURNISHED
ELECTRICAL
INLET
25 7/8"
( 657mm )
FINISHED FLOOR
1 1/8"
( 29mm )
11"
( 279mm )
Specifications and measurements are subject to change without notification.
Please visit halseytaylor.com for most current version.
Printed in the U.S.A.
Loading...