Halsey Taylor HTER-Q User Manual

This water cooler is certified to

NSF/ANSI 61.

GENERAL

Modular, electric refrigerated, wall-mounted
water cooler designed to be easily accessible
to physically challenged individuals. When
properly installed, unit meets state and federal
requirements as defined by the Americans with
Disabilities Act. Unit is certified to NSF/ANSI 61
and meets requirements of the Safe Drinking
Water Act. Unit provides 50° F water at 80° F
inlet water and 90° F ambient.

FOUNTAIN

Face-mounted, one-piece, non-corrosive
stainless steel cooler top, number 300 series
with satin finish and contour-formed basin.

BUBBLER

Exclusive one-piece, chrome-plated two-stream
mound-building bubbler with non-removable
anti-squirt feature and integral hood insures a
satisfying drink of water.

PUSH BAR ACTUATION MECHANISM

Self closing, light-touch push bar with raised
letters for the visually impaired.

PUSHBUTTON ACTUATION MECHANISM

Self-closing, vandal-resistant pushbutton does
not require grasping or twisting.

AUTOMATIC STREAM HEIGHT REGULATOR

Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatically
maintained under line pressures that vary from
20 to 105 psi.

INLET STRAINER

Easily cleaned in-line strainer screen traps
particles of 140 microns or larger before they
enter the waterway.

REFRIGERATION SYSTEM

Hermetically sealed, positive start compressor
with lifetime lubrication and built-in overload
protection, efficient capillary sizing, large
capacity dryer-strainer, and fan cooled
copper/aluminum condenser with self-lubricated
bearing. System uses R134A refrigerant.
Protected by Halsey Taylor’s Limited 5 Year
Warranty.

MOUNTING FRAME

Mounting frame is manufactured of corrosion
resistant, galvanized steel. Open construction
designed for ease of installation. Mounting
frame can be shipped in advance for rough-in
installation.

PANELS

Constructed of stainless steel, number 300
series with satin finish. Removable lower panel
providing access to plumbing and refrigeration
system. Panels overlap wall opening

1

/

2"

.

SUGGESTED SPECIFICATIONS

Shall deliver 7.5 GPH of 50° F water at 90° F
ambient and 80° F inlet water. Fountain shall
include push bar valve on front, contour-formed
basin to eliminate splashing and standing
water, and rounded corners and edges. Bubbler
shall be chrome plated, two-stream, mound­building type. Cooling unit shall have a high
efficiency positive start compressor using
R134A, with pressurized counterflow cooling
evaporator/chiller. Cooler shall comply with
ANSI 117:1 and ADA for visual and motion
disabilities. The manufacturer shall certify the
unit to meet the requirements of NSF/ANSI 61,
and the Safe Drinking Water Act. Unit complies
with ARI Standard 1010.

NOTE: Continued product improvement makes
specifications subject to change without notice.
See Halsey Taylor website for most current
spec sheet.

Standard finish is Stainless Steel

Optional Accessories (extra cost)

■■

Easy-Flex™Bubbler

■■

Water Filter

■■

Vandal Resistant Kit

Each HTER-Q consists of 3 cartons
as follows:

Mounting Frame
Cooling Unit-SJ8
Fountain, Panels & Misc. Parts

HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523

A33 / 1-2005

MODEL:■■HTER-Q

Barrier-Free Cooler

Classic™Series

www.halseytaylor.com

HT BARRIER-FREE SERIES

Model GPH Capacity Base F.L. Shipping Rated
No. Cooled to 50° F* Rate Amps Weight Watt

Ambient Air Temp

Cap. lb. Usage

70°F 80°F 90°F†100°F

HTER-Q 9.3 8.3 7.5 6.8 7.5 3.5 99 325

* With projector service and tap water at 80° F

For additional specification of the cooling unit, see specification sheet for Model SJ8 Remote in this catalog.

†

UL listed and complies with ARI Standard 1010

Trap and service stop not included

Halsey Taylor Barrier-Free Drinking
Fountains and Water Coolers conform
to The Americans with Disabilities Act
and American National Standards
Institute Specifications.

Printed in the U.S.A.

Barrier-Free Cooler

(CONTINUED)

WALL OPENING

IMPORTANT: It is necessary to create a wall
opening 18

3

/4

" W x 37

3

/4

" H and 4

1

/

2

" above the

floor line.

MOUNTING INSTRUCTIONS

Refer to rough-in for location of plumbing and
electrical sources. The support frame is to be
installed first. The shelf for the water chiller
should be assembled to the wall frame, and
then place chiller into position. Hang upper
fountain panel to hanger on frame. Fountain is
to be attached to panel and wall frame. Water
service line, waste line and electrical is
assembled as required. The bottom panel
is attached last, after a final check for leaks
and correct functions of fountains and chiller.
(For details see the installation instructions.)

Installation requires trap to be installed in
wall. Trap and service stop not included.

OPERATING PRESSURES:

Supply water - 105 psi maximum

ELECTRICAL DATA

Requires (3) wire 10 AMP branch circuit.
Standard 120 volt, 60 HZ, single phase.

Important: For recommended wall support see
installation instructions provided with fountain.

FRONT VIEW

TOP VIEW

SIDE VIEW

27" (686mm) for adult ADA.
Adjust other measurements accordingly.

LEGEND:

A = 3/8" O.D. TUBE CONNECT (CHILLER WATER INLET) SHUT OFF VALVE BY OTHERS
B = 1-1/4" O.D. WASTE TUBE (ELBOW & TRAP NOT PROVIDED)
C = ELECTRICAL INLET